Hunter Hydrawise HPC User manual

HPC - Using Hunter Remotes

The HPC face panel quickly and easily upgrades Pro-C® controllers (PC400 models

manufactured since March 2014) to next-generation smart controllers via the Hydrawise

platform. In addition, it lets contractors continue using their Roam and Roam XL remotes

for quick on-site management. HCC is also compatible with Hunter’s ROAM and ROAM XL

remotes, allowing for fast and reliable manual operation in the field from long-range

distances without the need for a smartphone. There is no need to remove the smart port

adapter from the controllers when doing a facepack upgrade.

Compatible models include all Hunter remotes: SRR, ICR, ROAM, and the ROAM-XL.

If the Smartport is not installed on the controller, see illustrations below for wiring

instructions.

Note: Any extension of the wiring on the SmartPort may result in an error message in

the controller display and possible malfunction of the remote unit due to radio interference.

In

some situations, lengthening of the harness may work fine, in others it may not work at all

(it is

site specific). In either case, extending the wiring harness should be done using shielded

cable to

minimize the possible effects of electrical noise. For easiest installation, order the Hunter

SmartPort shielded cable wiring harness. (P/N ROAM-SCWH) with a full 25' (7.6 meters)

of

shielded cable.

Wiring

1. Bottom 24 VAC terminal - Red wire

2. Second 24 VAC terminal - White wire

3. Remote terminal - Blue wire

Smart Port Wiring

Copyright 2020 Hunter Industries. All Rights Reserved. 1

Operation

The ROAM System will allow you to remotely turn on and off any station on your Hunter

controller with the press of a button. Once on, the station will run for the run time you have

designated in the remote. To remotely activate a station, follow the steps below:

1. Plug the receiver into a SmartPort® that is connected to a powered controller. The

receiver will beep 4 times followed by a 10-second pause and a single beep.

2. If your transmitter is not on (no display), wake it up by pressing and holding the MODE

button for 5 seconds. The Transmitter will display the active station.

3. Use the up and down buttons to display the station you would like to start.

4. Press the "Green Play Button" to start the station. The Transmitter will display the

Transmit icon . If you are near the receiver, you will hear it beep 2 times. This indicates

that the Receiver has received the command.

5. Press the "Red Stop Button" to turn off any station that is on. The display will show

the Transmit icon and receiver will beep again twice. The ROAM System is designed to

turn on

one station at a time (unless you activate a program). Therefore, turning a station on

while another station is operating will cause the operating station to turn off.

NOTE: The ROAM remote can activate any station on the controller whether the controller

dial is in the “SYSTEM OFF”, “RUN” or “RUN/BYPASS SENSOR” modes. If a sensor

device has been wired to the controller, the ROAM remote will NOT override the sensor for

Copyright 2020 Hunter Industries. All Rights Reserved. 2

manual operation. For more programming information, please see attached manuals for

both the ROAM and ROAM XL remotes.

Copyright 2020 Hunter Industries. All Rights Reserved. 3

This manual suits for next models

6

Table of contents

Other Hunter Controllers manuals

Hunter

Hunter XC hybrid Operating instructions

Hunter

Hunter NODE-BT User manual

Hunter

Hunter Pro-C User manual

Hunter

Hunter Hydrawise Pro-HC Quick start guide

Hunter

Hunter XC Hybrid Operating instructions

Hunter

Hunter X-CORE XC-800I Operating instructions

Hunter

Hunter Hydrawise HCC-800-PL User manual

Hunter

Hunter Hydrawise Pro-HC User manual

Hunter

Hunter ACC-1200 User manual

Hunter

Hunter Hydrawise Pro-HC User manual

Hunter

Hunter WVC Operating instructions

Hunter

Hunter NODE-100 Operating instructions

Hunter

Hunter X-CORE User manual

Hunter

Hunter 99373 User manual

Hunter

Hunter 99111 User manual

Hunter

Hunter Eco-Logic 6 Operating instructions

Hunter

Hunter ECO LOGIC User manual

Hunter

Hunter Pro-C Operating instructions

Hunter

Hunter ICC2 Installation manual

Hunter

Hunter X-CORE XC-2 Parts list manual

Hunter

Hunter NODE-BT User manual

Hunter

Hunter XC HYBRID Series Guide

Hunter

Hunter HCC Installation manual

Hunter

Hunter Smart Valve Controller Operating instructions

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual