Huawei FusionModule500 User manual
Huawei Technologies Co., Ltd.
Issue: 02
Date: 2021-06-30
FusionModule500 Smart Mini Data Center
Quick Guide (02116382)
1Copyright © Huawei Technologies Co., Ltd. 2021.
All rights reserved.
Product Overview
Item Specifications
Cabinet dimensions (H x W x D)
(unit: mm)
Converged Cabinet: 2000 x 600 x
1100
Installation scenario
Supports only a single cabinet.
Installation space
The cabinet provides 42 U available space. The mounting
bars are adjustable. The installation position for horizontal
rPDUs
is set at the rear of the cabinet.
Power distribution
6 kVA UPS
rPDU
: horizontally installed; options: IEC and GB
Lithium battery: 100 Ah/48 V DC
Operating temperature
Indoor: 0
°C to 40°C
Operating humidity
5%
–95% RH
IP rating
IP20
Maximum power of a single cabinet
3 kW
Installation mode
Installed on a concrete floor or an electrostatic discharge
(ESD) floor
Altitude
≤ 1000 m (
derated
when the altitude ranges from 1000 m
to 4000 m)
Components to Be
Installed Onsite
Lithium battery
Water sensor
Temperature and humidity
(T/H) sensor
rPDU
LAN Switch
(Optional)
Server
(Optional)
IVS (Optional)
Camera
(Optional)
•The component layout is only for reference. The actual installation positions prevail.
•If the IVS, server, and LAN switch are configured, determine their installation positions
based on the site requirements.
2
Hardware Installation
1Installing the Cabinet
1. Determine the cabinet position based
on the engineering layout diagram.
2. Place the cabinet at the correct
installation position.
3. Level the cabinet using a wrench.
•Use a measuring tape to check
that the vertical distance between
the top of the 2000 mm high
cabinet and the floor is 2000 mm
(+3 mm). Then use a level to
check that the cabinet is level.
•Do not remove the anchor bolts.
Otherwise, rework is required if
the cabinet height does not meet
requirements.
2Installing a Drainage Pipe for the Smart Cooling Product
1. Remove the baffle plate from the smart cooling product.
2. Cut the rubber plug of the water pipe hole at the bottom of the cabinet and route the
drainpipe.
3. Install the baffle plate for the smart cooling product.
3
1. Push a lithium battery into the
cabinet and secure it.
3Installing Power Supply and Distribution Devices
3.1 Installing Lithium Batteries 12.1
3.2 Install Busbars
3.3 (Optional) Installing Busbars
•If there is more than one lithium
battery, install busbars.
•The busbars need to be installed 2
U above the last lithium battery.
Determine the busbar installation
position based on the lithium
battery configuration.
Install lithium batteries in the 11th U and
higher positions of the cabinet.
Install rPDUs in the 11th U and 13th U
positions of the rear door of the cabinet.
4Installing Monitoring Devices
4.1 Installing the SIM Card and Antenna
3. Attach the antenna to the middle of the
cabinet top.
4. Connect the antenna cable.
1. Remove the ECC800-Pro main control module.
2. Install the SIM card.
4.2 Installing a PAD
1. Adjust the PAD mounting support to match the dimensions of the PAD to be installed.
2. Remove the nuts from the PAD mounting support and install the support.
3. Route the PAD power cable through the cable hole and connect the cable.
4. Clamp the PAD.
5. Connect the ECC800-Pro USB cable to the charging port on the PAD.
Adjusting
screws
4
4.3 Installing T/H Sensors
1. Unpack the two T/H sensors. Attach one
sensor to the right post at the 33th U
position on the front door and the other
to the right post at the 11th U position
on the rear door of the cabinet.
2. Set the DIP switch address of the T/H
sensor on the front door to 2 and that
of the T/H sensor on the rear door to 1.
3. Insert the pre-routed cables into the
ports on the T/H sensors on the front
and rear doors.
•The installation positions of the T/H sensors can be adjusted as required.
•The default device address is 1.
Installing Remote T/H Sensors for
Smart Cooling Products Installing Cabinet T/H Sensors
1. Unpack the two T/H sensors and attach
one sensor to the mounting bars at the
39th U position on the front door and the
other to the 37th U position on the rear
door of the cabinet.
2. Set the DIP switch address of the T/H
sensor on the front door to 2 and that of
the T/H sensor on the rear door to 1.
3. Insert the pre-routed cables into the
ports on the T/H sensors on the front and
rear doors.
4.4 Installing an Electrode
Water Sensor
1. Place the water sensor on the floor
under the cabinet.
2. Route the water sensor cable through
the cable hole at the bottom of the
cabinet, and connect the cable to the
water sensor cable connected to the
ECC500.
3. Install the water detector.
4.5 (Optional) Installing a Server
1. Determine the installation position of the server and check whether floating nuts are installed.
If not, install them first.
5
2. Install guide rails. 3. place the server on the guide rails, and push
it into the cabinet.
4. Secure the server.
5. Connect the server power cable.
a. Wear an ESD wrist strap or ESD gloves.
b. Connect one end of the power cable to
the cable port on the AC power module
of the server.
c. Use a hook-and-loop fastener to secure
the power cable.
d. Route the power cable along the cable tray neatly, use cable ties to bind the power cable,
and use diagonal pliers to trim off the excess of the cable ties.
6
4.6 (Optional) Installing a Camera
1. (Optional) Install an SD card. 2. Secure the camera to the
mounting plate.
(1) Cable outlet
4. Adjust the camera.
5. Install the transparent cover.
3. Secure the mounting plate to the top
of cabinet front door.
4.7 (Optional) Installing a LAN Switch
1. Install guide rails and floating
nuts.
2. Secure the LAN switch.
3. Connect the power cable of
the LAN switch.
4. Connect any port from 1 to 24
on the LAN switch to the
WAN_1 port on the ECC800-
Pro using a network cable.
5. Insert a power module into
the power slot of the LAN
switch.
It is recommended that the
LAN switch be installed in the
35th U position of the cabinet.
You can adjust the position
based on the site requirements.
7
4.8 (Optional) Installing an IVS1800
1. Install hard disks.
a. Remove screws, and take off the chassis cover.
b. Remove two black screws on each side of the chassis and the silvery white one on top of the
hard disk tray, raise the hard disk tray by 45 degrees, and take out the upper and then lower
layers of hard disk tray.
c. Place the hard disks with ports
facing upwards and align the
screw holes on the hard disk
tray with the hard disks and
fasten the screws.
d. Insert the hard disk tray back at 45 degrees with the opening of its locking buckle facing
downwards, hold the screw in the red-framed part to lower the hard disk tray until it is level,
and fasten the black screws on the left and right sides and the white screw on the top.
e. Connect data and power cables to hard disks.
8
f. Close the chassis cover, and use a PH2 screwdriver to fasten the rear screws.
2. Install the device.
a. Install the cage nuts on guide rails, and Install guide rails.
b. Install the cage nuts that secure the IVS1800.
c. Install mounting ears.
8
d. Install the IVS1800 in the cabinet.
3. Power on the device.
4.9 (Optional) Installing a Fire Extinguishing Module
1. (Optional) Installing guide rails to the installation position of the fire extinguishing module.
2. Secure the fire extinguishing module.
Other manuals for FusionModule500
7
Table of contents
Other Huawei Server manuals
Huawei
Huawei SVN2000 Series User manual
Huawei
Huawei FusionServer Pro CH121 V5 User manual
Huawei
Huawei FusionServer Pro 2288H V5 User manual
Huawei
Huawei FusionServer Pro CH121 V5 V100R005 Manual
Huawei
Huawei X6800 User manual
Huawei
Huawei V500R003C00 Operating manual
Huawei
Huawei 5288 V5 User manual
Huawei
Huawei FusionServer Pro 1288H V5 Quick reference guide
Huawei
Huawei XH628 V5 User manual
Huawei
Huawei FusionServer Pro CH242 V5 Quick reference guide
Huawei
Huawei FusionServer Pro 2288H V5 User manual
Huawei
Huawei Tecal RH2285 User manual
Huawei
Huawei 2288H V5 User manual
Huawei
Huawei FusionModule2000 V500R003C10 Operating manual
Huawei
Huawei G5500 User manual
Huawei
Huawei OptiX PTN Series User manual
Huawei
Huawei UPS5000-E-****-FM series User manual
Huawei
Huawei FusionServer Pro 5885H V5 Quick reference guide
Huawei
Huawei FusionServer Pro 1288H V5 User manual
Huawei
Huawei X6000 User manual
