HP StorageWorks 7100 - Virtual Array Quick guide

Replacement Procedure: VA7.x Disk Module, 18GB-36GB-72GB

You can add or replace disks to increase storage capacity or eliminate faults. (See Chapter 3 of the

HP StorageWorks Virtual Arrays VA 7000 Family User’s and Service Guide for troubleshooting procedures.)

Disks must be Fibre Channel (FC) and 3.5 inches wide but can vary in capacity.

For current information about supported disks, consult an HP sales representative.

You do not need to turn off the array to replace a disk or filler.

Caution Do not remove hot-pluggable components until you have the

replacement parts and are ready to install them. An empty slot will cause

uneven cooling and eventual overheating.

Caution Parts can be damaged by electrostatic discharge. Please ensure

that ESD measures are in place.

Step 1

Open the Disk Replacement Kit and inspect the contents per the first step of the Disk Replacement Sheet

included with the replacement drive.

Step 2

Caution Touching exposed electrical circuitry on the disk can damage the disk. Be sure you are grounded

and be careful not to touch exposed circuits.

Disk modules are fragile and ESD sensitive. Dropping one end of the disk just two inches is enough to cause

permanent damage. In addition, static electricity can damage the disc. Grasp disks only by their handles (A

in Figure 1) and carriers (D), and follow strict ESD procedures.

Figure 1: Disk Module Installation

A extraction handle

C LEDs

B cam latch D carrier

Step 3

Push down release tab (B in Figure 1), pull up the lever (A) on disk to be replaced.

Step 4

Caution Wait 15 seconds for the disk to spin down. There is a danger of damage to the disk if it is dropped

due to gyroscopic effects. Wait for a spinning disk to stop spinning prior to removing it from the product.

Step 5

Pull the disk to be replaced from the slot.

Step 6

Caution DO NOT leave the disk slot empty for more than 5 minutes, as proper cooling/airflow depends on

all slots being full.

Step 7

Verify that the disk module extraction handle (A in Figure 1) is open . Place your thumb behind the

extraction handle and with your finger, push the latch tab (B) toward your thumb.

Note It is important that the new disk is of the same capacity (in GB) or larger than the disk being replaced.

Step 8

Push the replacement disk module, capacity label up, into the empty slot.

Step 9

Push down the lever (A in Figure 1) on the disk. It will click into place.

Step 10

The drive will now begin an automatic formatting process. Depending on your system configuration, the time

to complete will vary.

Note An exchange disk drive comes formatted with 512-byte sectors. After installation, the controller starts

the Auto Format process to automatically format the disk drive with 520-byte sectors. Table 1 indicates the

times required for formatting the different capacity disks.

Note Depending on the total amount of memory in your array and your specific configuration, a complete

format and rebuild process may take between 4 and 24 hours. As per Step 11 (below) monitor your array for

correct LED behavior.

Table 1: Raw format Times (Verify Off)

Disk

Capacity Format Time

(Minutes)

18 GB 15k 8

36 GB 10k 20

73 GB 10k 28

Caution To prevent corruption of the disk format, do not remove a newly installed disk drive or power-off the

array during the AutoFormat process. If a disk is removed during an Auto Format, the array will automatically

re-start the Auto Format process from the beginning.

Step 11

Monitor the Disk LEDs,

Figure 2: Disk Drive LEDs (Left: VA 71/7400 A/AZ; Right: VA 7100 D)

Note After installation, the controller starts the Auto Format process. During this time, the green disk activity

LED (A in Figure 2) will be flashing. The green (A) LED will also blink with I/O activity to the disk. See Table

2 for a full list of disk LED behaviors. The amber disk fault LED (B) will flash during an Auto Format process.

The amber system fault LED will also flash.

If you observe different results, further Troubleshooting may need to be carried out. (See Chapter 3 of the

HP StorageWorks Virtual Arrays VA 7000 Family User’s and Service Guide for troubleshooting procedures.)

Table 2: Disk Drive LEDs Status Indications

Disk

Activity

(Green*)

Disk Fault

(Amber**)

Indication

Off Off Disk not under power.

On Off Disk drive under power and operating normally.

Off On Disk drive fault.

On On Disk drive fault.

Flashing Off Disk drive self-test in progress or I/O activity.

On/Off Flashing Host is identifying disk drive.

*Controlled by the disk drive.

**Controlled by the array controller.

Procedure Completed!

“Congratulations!”

Other manuals for StorageWorks 7100 - Virtual Array

Table of contents

Other HP Storage manuals

HP P9000 User manual

HP Data Vault User manual

HP C2488A Product manual

HP StorageWorks 8B - FC Entry Switch Instruction Manual

HP StorageWorks 7100 - Virtual Array Technical document

HP Xw4550 - Workstation - 2 GB RAM User manual

HP StorageWorks All-in-One SB600c - Storage... User manual

HP Ultrium Drive Product manual

HP Ultrium 232e User manual

HP ProLiant DL100 G2 DPSS User manual

HP StorageWorks XP10000 - Disk Array User manual

HP C737990900 Product manual

HP StorageWorks Modular Smart Array 500 System Manual

HP StoreOnce 2700 Operator's manual

HP AU183AA - 2TB Personal Media Drive Use and maintenance manual

HP P5389A - Intel Pentium III-S 1.4 GHz Processor... User manual

HP Pavilion p6000 - Desktop PC Guide

HP 418371-B21 - Dual Port 72 GB Hard Drive User manual

HP StorageWorks Ultrium 215 User instructions

HP StorageWorks 7110 - Virtual Array User manual

HP StoreVirtual P4000 G2 Service manual

HP StorageWorks SDLT Series User manual

HP StorageWorks Ultrium 1760 User manual

HP StorageWorks P4000 Series User manual

Popular Storage manuals by other brands

QNAP

QNAP TS 32PXU Series user guide

LaCie

LaCie RUGGED RAID user manual

Freecom

Freecom CLS DOCK Quick install guide

PNY

PNY Attache P-FD64MBATT3 install guide

OLT

OLT 6x6 Maximizer Assembly manual

Transcend

Transcend JetFlash 160 Specifications

LaCie

LaCie RUGGED MINI user manual

Thunderbolt

Thunderbolt 600 user manual

Panasonic

Panasonic LB-DH8 series Operator's guide

Intel

Intel RAID High Availability user guide

LaCie

LaCie 12big Thunderbolt 3 Quick install guide

Spectra Logic

Spectra Logic T-Series Spectra T50e quick start guide

Panasonic

Panasonic LKM-F931-1 instruction manual

Tabernus

Tabernus Enterprise Erase E2400 user guide

Rocstor

Rocstor COMMANDER 3F series user manual

Western Digital

Western Digital Ultrastar Data60 installation guide

Dell

Dell PowerVault MD3600f Series Getting started

CFI

CFI TERA STOR SATA RAID IV user manual