HP Designjet L65500 User manual
HP 104-in Dual Roll Kit
User’s guide
© 2010 Hewlett-Packard Development
Company, L.P.
First edition
Legal notices
The information contained herein is subject
to change without notice.
The only warranties for HP Products and
services are set forth in the express
warranty statement accompanying such
products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable
for technical or editorial errors or omissions
contained herein.
Table of contents
1 Introduction ..................................................................................................................................................... 1
Purpose ................................................................................................................................................ 1
Main components ................................................................................................................................. 1
Requirements ....................................................................................................................................... 1
2 Use of the dual-roll spindle ............................................................................................................................ 2
Load rolls onto the spindle ................................................................................................................... 2
Load rolls into the printer ...................................................................................................................... 5
3 Troubleshooting ............................................................................................................................................ 10
4 Specifications ................................................................................................................................................ 11
Appendix A Changes to roll loading and unloading .................................................................................... 12
ENWW iii
iv ENWW
1Introduction
Purpose
The Dual Roll Kit enables you to print on two rolls of substrate simultaneously.
Main components
The Dual Roll Kit includes the following components.
●Two dual-roll spindles, each including one differential hub
●One pair of substrate edge holders
●One Allen key 4
●One Allen key 6
●Spindle supports on which to rest the spindle when it is not in use
Requirements
Before using the Dual Roll Kit with an HP Designjet L65500 printer, you must check that the printer's
firmware and HP Internal Print Server software are up to date.
Go to http://www.hp.com/ and click Support & Drivers > Download drivers and software (and
firmware), enter the product name L65500, click the name of your operating system, and download
the latest firmware and the latest Internal Print Server, if you do not already have them.
If the firmware and software versions on HP's Web site are still dated 2009, try the following FTP site.
FTP System ftp://ftp.usa.hp.com/ (15.192.32.78)
Login dualroll
Password (case-sensitive) Milieux2
Access type read-only
or ftp://dualroll:[email protected]/
ENWW Purpose 1
Introduction
2 Use of the dual-roll spindle
Load rolls onto the spindle
The dual-roll spindle is marked to assist you in positioning the differential hub.
Loading the dual-roll spindles
1. Ensure that the differential hubs on the input and output spindles are aligned with each other.
2 Chapter 2 Use of the dual-roll spindle ENWW
Dual-roll spindle
2. When both differential hubs are correctly positioned, use an Allen key 6 to tighten the screws
and secure them in place. If a differential hub is loose, the substrate could become skewed
during printing.
TIP: You should tighten the screw until the washer touches the bolt. If you can still see the
yellow spring, tighten the screw further.
3. At each end of the spindle, unscrew and remove the outer parts of the hub, using an Allen key 4.
4. Unscrew and remove the inner part of each hub.
ENWW Load rolls onto the spindle 3
Dual-roll spindle
5. Insert the first roll on the spindle.
6. Replace the hub, and secure it with the Allen key.
7. Insert the second roll on the spindle.
8. Replace the hub, and secure it with the Allen key.
9. Ensure that the end of the right-hand roll is located within the maximum allowed distance from
the right-hand end of the spindle: it should be between the gear and the dashed line.
10. Ensure that the roll core fits tightly on the hub.
4 Chapter 2 Use of the dual-roll spindle ENWW
Dual-roll spindle
11. Ensure that the roll core fits tightly on the differential hub.
12. Load the spindle at the rear of the printer, and secure the spindle latches.
13. Use the same process to load the output spindle at the front of the printer, but load the spindle
with two empty cores to receive the printed substrate.
Load rolls into the printer
The two substrate rolls are mounted on the rear dual-roll spindle and will be collected on the front
dual-roll spindle. The substrate goes from the rear spindle over the main roller, over the platen, over
the front roller and then to the front spindle.
NOTE: You can load substrate with the printed face inwards or outwards on the spindle, in which
case the spindle will turn in the opposite direction. The printer asks you for the winding direction if it
cannot detect it automatically.
Before loading two rolls into the printer, you must have both rolls loaded on the rear dual-roll spindle
and two empty cores loaded on the front dual-roll spindle. See Load rolls onto the spindle on page 2.
1. Tell the printer that you are going to begin loading for dual-roll printing.
2. Remove the substrate edge holders in the print platen, or move them aside, so that they do not
get in the way while loading the substrate.
CAUTION: Loading the substrate on top of the edge holders could severely damage the
printheads and carriage.
3. Lift the substrate pressure handles at the rear of the printer.
ENWW Load rolls into the printer 5
Dual-roll spindle
4. If you need to raise the carriage beam, go to the front panel and select the Substrate menu ,
then Substrate management, and press OK. Select Carriage beam position > Move to
highest position. This process takes about 2 minutes to complete.
The printer raises the carriage beam, making it easy to insert the substrate. This process takes
about 2 minutes to complete. During this period, you can load the input and output rolls.
NOTE: While the carriage beam is rising, you can stop it by pressing the Cancel key.
5. You may find it helpful to lock the differentials on the input and output spindles while loading.
6. Bring the new rolls on their spindle to the rear of the printer, with the geared end of the spindle
on the left.
7. If the two rolls are of unequal lengths, the longer roll should be on the right as seen from the
front of the printer; on the left as seen from the rear.
NOTE: When the shorter roll comes to an end, you should lock the differential hub if you intend
to continue printing on the longer roll.
8. Rest the ends of the spindle on the platforms provided at the rear of the printer; plastic pads are
provided to absorb the impacts.
6 Chapter 2 Use of the dual-roll spindle ENWW
Dual-roll spindle
This manual suits for next models
2
Table of contents
Other HP Printer Accessories manuals
HP
HP Jetdirect 2800w User manual
HP
HP C8519A - LaserJet 9000 B/W Laser Printer User manual
HP
HP Ink Tank 110 series User manual
HP
HP Designjet T1500 series User manual
HP
HP LaserJet M5025 MFP User manual
HP
HP Designjet 8000s Series User manual
HP
HP Digital Sender 8100C User manual
HP
HP Laserjet,Color Laserjet 4si User manual
HP
HP 4500 - DesignJet Color Inkjet Printer User manual
HP
HP Q3952A User manual
HP
HP LaserJet Enterprise M4555 User manual
HP
HP DESIGNJET 3D User manual
HP
HP CM4540 COLOR LASERJET Manual
HP
HP LaserJet 4MV Series User manual
HP
HP 4600 - Color LaserJet Laser Printer User manual
HP
HP DesignJet 5000 cp User manual
HP
HP LaserJet Enterprise 600 User manual
HP
HP 4650 - Color LaserJet Laser Printer User manual
HP
HP C6615D User manual
HP
HP C2655A - Deskjet 340 Color Inkjet Printer User manual
