Honeywell Code Encryptor II User manual
Installation Manual
Street Smart Security
Now with
Automatic Alarm
Recognition
Patent Pending - Part #CE2Y
PREVIOUS
Code Encryptor II
Locationofthecontrolmoduleisthemostimportantdeterminingfactorforrangeand
reliability of your Code Encryptor. Select a location that is as centrally located as pos-
sible.Keepinmindthatyourcustomerwillwanttocontroltheoperationofthegarage
doorfrom thedriveway, andwill alsoexpect theuse ofthe remotefor alarmOn/Off
in the area of entry and exit.
SincetheCodeEncryptorusesthecommunicationbuswiresfromthekeypad,youmay
want to place the receiver in or near the garage to easily control the following
• Easy connection to the garage door push button
• Easy visual LED status mounting location
• Easy connection to the keypad wires for complete alarm control
Although you can wire at the panel, it may reduce labor by installing the Code
Encryptor II receiver at the point of entry. In most cases that is the garage which will
provide an easy installation for garage door Open/Close, status indicator and alarm
controls through the keypad. DO NOT MOUNT THE CONTROL MODULE IN
THE ALARM PANELS METAL ENCLOSURE.
Recommended
placement for
Code Encryptor
CODE
ENCRYPTOR
1
Garage
Basement
Bedroom
Attic
Point of Entry
Wiring Diagram
2
Yellow Connect to yellow of keypad
*Moose panels connect to
white of keypad
Green Connect to green of keypad
Gray (-) Channel 2 Timed Output
Red/White Channel 2 N/O relay
(Garage Door Pushbutton)
White Channel 2 Common
(Garage Door Pushbutton)
Brown Channel 3 Common
(5amp)
Brown/White Channel 3 N/O
(5amp)
Blue/Green Channel 3 N/C (5amp)
Red +12VDC
Black (-) Ground
Purple LED (-) Output
Button 1 Alarm ON/OFF/STAY**
Button 2 Garage Door OPEN/CLOSE
Button 3 PANIC OUTPUT
Hold for 3 seconds
RELAY OUTPUT
Press and Release
**Press and hold for 3 seconds to
activate “STAY” mode
Button 1
Button 2
Button 3
3
Installation
Red Aux +
Black Aux -
Yellow Keypad Data Line
Green Keypad Data Line
CODE
ENCRYPTOR
Alarm Panel
+ -
Aux
Black Red
123
456
789
Green Yellow LED
Program
Button
Channel 3
Jumpers
Alarm
Keypad
4
Wiring and Auto Recognition
COMPLETE STEPS 1-8
Step 1) Unplug the receiver from the wire harness.
Step 2) Wire the Red, Black, Yellow and Green to the keypad.
RED Connect to Keypad Red or Aux (+)
BLACK Connect to Keypad Black or Aux (-)
GREEN Connect to Keypad Green
YELLOW Connect to Keypad Yellow
*Moose ZX200/400/900/950 Connect to the White wire.
NOTE: You can make these connections at the panel or at the keypad
itself. If you place the Code Encryptor II in the garage or any other
location away from the panel you may choose to wire the Code
Encryptor II directly to the keypad.
Step 3) Make sure the alarm panel is powered up and operating.
Step 4) While watching the LED light on the Control module, plug the receiver into
the Code Encryptor II harness.
Step 5) The LED will blink 1 time on power up, after 2 seconds COUNT the flashes
that you see. The corresponding flashes will indicate which panel the Code
Encryptor II has detected.
*If you are using a DSC 1550 or a Caddx 8980E see page 16.
5
Automatic Recognition Continued:
Number of Flashes Alarm Panel detected by the CE II
1 No Alarm connected (CE II defaults to relay mode)
SEE PAGE 15 “Default Mode”
2 Napco 1000E Series (including 1008E, 1016E, etc.)
3 Moose Z880/Z900/Z950
4 Caddx 8600E, 8980E
5 Ademco Non Addressable
6 Ademco Addressable
7 DSC 1555/1565/5010 (Power 832)
8 DSC 1550, 2525, 2550, 3000
9 Moose ZX200/ZX400
10 Moose Z1100/Z1100E, ADT A910
Go to Mandatory Programming (Steps 6, 7 and 8)
NOTE: If the CEII does not detect correctly,
call Technical Toll Free 888-768-2846
7am-5pm PST
Mandatory Programming
Programming a User Code is mandatory when using the Code Encryptor II. This
gives the Code Encryptor microprocessor a User Code to arm and disarm the panel.
Step 6) Verify that the four-digit code you plan to teach the Code Encryptor II is a
valid four-digit user code. Example: From the keypad use that four-digit
code to arm the panel. If the panel arms, that is a good code. If it does
not, program that user code into the alarm panel. – The Code Encryptor II
uses that four-digit code to arm and disarm the panel, thus that code must
be valid.*
Step 7) Press and HOLD the program button on the receiver. The light will come
ON and stay ON for three seconds then turn OFF. Once the light turns
off, RELEASE the program button, the light will begin to flash rapidly.
Step 8) Using the keypad, slowly and firmly enter the four-digit user code. After
the fourth entry the LED will stop flashing. This code has now been
entered into the Code Encryptor’s non-volatile memory. The Code
Encryptor will remember this user code in the event of a power failure. To
change to a new user code, repeat steps 7 and 8 above.
*NOTE: We recommend using a user code that the customer cannot
change. If the user code that is programmed into the CE Module is
changed, the Code Encryptor II will not disarm the alarm panel.
6
7
Mandatory Programming Continued
Press and Release button #1 Alarm “Away”
Press and Release button #1 Alarm “Disarm”
Press and Hold for 3 seconds Alarm “Stay” or “Bypass”
NOTE: The Code Encryptor II will arm in the AWAY mode even if you
are outside the house. You do not have to arm the alarm before you
exit. We do however recommend that you Arm the alarm system with-
in sight of the status LED or keypad to verify that the alarm has
received and responded to your remote request.
SEE PAGE 16 FOR DSC 1550 AND CADDX 8980E.
The Code Encryptor II on the following panels self enroll themselves as a specific
keypad address code.
• Ademco addressable Address #3
• Moose ZX200/ZX400 addressable Address #4
DO NOT USE ANY OF THESE ADDRESS CODES IF YOU ARE USING ONE OF THE
ABOVE PANELS. EXAMPLE: If you are using an Ademco Addressable, no keypads
can use address #3 since the CE II will automatically enroll itself as address #3.
LED Wiring
DO NOT CONNECT LED DIRECTLY TO GROUND!
The LED is a low voltage type and must run through the Code Encryptor II. If you
attempt to connect the purple wire directly to ground (-) the LED will burn and will
NOT operate again.
Go TO Channel 2 Outputs
8
Purple-
Connect to purple
of the wire harness.
Red (Aux+)
9
Channel 2 Outputs
(Every time button #2 is pressed, two outputs happen simultaneously.)
Output #1 Momentary Contact Closure for Opening and Closing
garage door (See Garage Door Interface)
Output #2 500ma (-) output for 3 minutes, (See Channel 2 Timed Output)
Garage Door Interface
All garage doors have a wall mounted push button that activates the door via a
two-wire connection. Make your connection at the push button switch or at the
garage door motor where these two wires terminate. The Code Encryptor II will
interface with this connection by attaching the red/white and white wires from the
Code Encryptor II to these two wires. If you choose to connect to the motor, trace the
wires from the push button to the motor to determine the proper connection point.
Most garage doors (except MOM Crusader models) use terminals #1 and #2. For
MOM Crusader models, use terminals #2 and #3.
Garage Door Motor
Terminals
1 2 3
Red/White
(Channel 2 output)
White
(Channel 2 common)
Other manuals for Code Encryptor II
1
Table of contents
Other Honeywell Security System manuals
Honeywell
Honeywell Ademco Lynx Touch User manual
Honeywell
Honeywell Le Sucre User manual
Honeywell
Honeywell Friedland GlobalGuard User manual
Honeywell
Honeywell LYNX Touch Security System User manual
Honeywell
Honeywell PID-95P Guide
Honeywell
Honeywell Friedland HISK1 User manual
Honeywell
Honeywell LYNX Touch 7000 User manual
Honeywell
Honeywell Ademco VISTA-20P Operating instructions
Honeywell
Honeywell TCPA2B User manual
Honeywell
Honeywell INTELLIGUARD 9000 User manual
Honeywell
Honeywell ADEMCO LYNXR-ISIA Assembly instructions
Honeywell
Honeywell ESSER User manual
Honeywell
Honeywell Lynx Plus Series User manual
Honeywell
Honeywell VISTA-21iP User manual
Honeywell
Honeywell Friedland HISK1 User manual
Honeywell
Honeywell GKP-S8M Setup guide
Honeywell
Honeywell VISTA-128BPT Assembly instructions
Honeywell
Honeywell Fire-Lite Alarms ANN-80 Series Technical manual
Honeywell
Honeywell Ademco VISTA-32FB User manual
Honeywell
Honeywell VISTA-32FBPT User manual
Popular Security System manuals by other brands
EDM
EDM Solution 6+6 Wireless-AE installation manual
Highway Safety Group
Highway Safety Group EA401 user manual
Siren
Siren LED GSM operating manual
Detection Systems
Detection Systems 7090i Installation and programming manual
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 instructions
Siemens
Siemens FDM273 manual