Honeywell RFID Kit User manual
Printer RFID Kit
For PX4ie, PX6ie
Installation Guide
PX4-6IE-RFID-IG-1Rev A
01/20
PX4ie/PX6ie RFID Kit Installation Guide 1
Introduction
The RFID kit provides RFID functionality for PX4ie and PX6ie printers. With this
kit installed, the PX4ie or PX6ie printer can read and write to RFID tags.
These instructions describe how to install the following RFID kits:
• PX4ie 915 MHz RFID Kit (P/N 50147009-001)
• PX4ie 869 MHz RFID Kit (P/N 50147010-001)
• PX6ie 915 MHz RFID Kit (P/N 50147011-001)
• PX6ie 869 MHz RFID Kit (P/N 50147012-001)
For more information about using RFID features on the PX4ie or PX6ie, see the
EasyCoder Printer RFID User’s Guide (P/N 934-041-xxx).
Contents
• One of the following RFID interface boards:
• RFID interface board with IM11 869 MHz radio module
• RFID interface board with IM11 915 MHz radio module
• One of the following lower media guides:
• PX4ie lower media guide with RFID antenna
• PX6ie lower media guide with RFID antenna
• Dual slot I/O cable
• M3x5 screw (2)
• M4x5 screw
• Spacer screw
2 PX4ie/PX6ie RFID Kit Installation Guide
Requirements
• A #T10 and a #T20 Torx screwdriver.
• A slotted screwdriver.
Installing the RFID Kit
Note: This procedure applies to both the PX4ie and PX6ie. For simplicity, the
PX4ie is depicted in the illustrations.
Warning: The installation described in this section must only be
performed by an authorized service technician.
Honeywell assumes no responsibility for personal injury
or damage to the equipment if the installation is
performed by an unauthorized person.
Follow ESD
Procedures
Follow standard ESD guidelines to avoid damaging the equipment.
Caution: Before you begin, turn off the printer and disconnect the
power cord and communication cables.
Caution: Before you begin, turn off the printer and disconnect the
power cord and communication cables.
PX4ie/PX6ie RFID Kit Installation Guide 3
1. Open the front door and right side door.
2. Remove the eight #T10 Torx screws and remove the left side door.
Screw
(8 places)
4 PX4ie/PX6ie RFID Kit Installation Guide
3. Release the lower media guide latch.
4. Carefully remove the lower media guide and upper media guide assembly.
5. Remove the upper media guide from the lower media guide.
Lower media
guide latch
Upper and lower media
guide assembly
PX4ie/PX6ie RFID Kit Installation Guide 5
6. Route the antenna cable from the RFID lower media guide through the
opening in the print engine base. Make sure to route the cable in front of
the label stop sensor (LSS) guide bar.
7. Slide the RFID lower media guide into the printer. Insert the pins on the
guide into the holes on the print engine base.
8. Snap the RFID lower media guide into place.
9. Insert the upper media guide.
RFID lower
media guide
6 PX4ie/PX6ie RFID Kit Installation Guide
10. On the back of the printer, remove the two screws that secure the cover
plate to slot 1 or slot 2, and remove the cover plate.
Note: You need to use the first available slot on the printer starting from the left
(slot 1).
11. Connect the dual slot I/O cable to the main board.
12. Connect the dual slot I/O cable to the RFID interface board. Use the
connector 1 for slot 1 and connector 2 for slot 2.
13. Slide the RFID interface board into the printer.
14. Secure the RFID interface board with the two screws you removed in Step 9
or with the two included M3x5 screws.
PX4ie/PX6ie RFID Kit Installation Guide 7
15. Secure the RFID interface board to the circuit board with the M4x5 screw
and spacer screw. For slot 1, use the spacer screw on the main board. For
slot 2, use the spacer screw in the kit.
16. Connect the antenna cable to the RFID interface board.
17. Attach the left side door to the printer.
18. Close the front and right side doors.
8 PX4ie/PX6ie RFID Kit Installation Guide
Support
To search our knowledge base for a solution or to log into the Technical Support
portal and report a problem, go to www.hsmcontactsupport.com.
Documentation
Product documentation is available at www.honeywellaidc.com.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and click Resources >
Product Warranty.
Patents
For patent information, see www.hsmpats.com.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in spec-
ifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether any
such changes have been made. The information in this publication does not
represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from the furnish-
ing, performance, or use of this material. HII disclaims all responsibility for the
selection and use of software and/or hardware to achieve intended results.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied, repro-
duced, or translated into another language without the prior written consent of
HII.
Copyright2009-2020 Honeywell International Inc. All rights reserved.
Table of contents
Other Honeywell Printer manuals
Honeywell
Honeywell MP Nova Mark II User manual
Honeywell
Honeywell IMPACT IHR810 User manual
Honeywell
Honeywell PX4i User manual
Honeywell
Honeywell E-Class MK IIIA User manual
Honeywell
Honeywell PM42 User manual
Honeywell
Honeywell MP Compact4 User manual
Honeywell
Honeywell PRU0901 User manual
Honeywell
Honeywell CN51 PrintPAD User manual
Honeywell
Honeywell PC300T User manual
Honeywell
Honeywell PRU7070 User manual
Honeywell
Honeywell MP Compact Mark III User manual
Honeywell
Honeywell PC43K User manual
Honeywell
Honeywell PC42d User manual
Honeywell
Honeywell 6824 User manual
Honeywell
Honeywell PM43 User manual
Honeywell
Honeywell E-Class Series User manual
Honeywell
Honeywell CN51 PrintPAD User manual
Honeywell
Honeywell PX940 User manual
Honeywell
Honeywell Intermec PD43 User manual
Honeywell
Honeywell PC45 Series User manual
