Honeywell Fire-lite FFT User manual

FFT

Fire Fighter Telephone Module

Product Installation Drawing

Document 52246 RevA 1/16/08 ECN 07-873

CAUTION! Make sure to observe all of the following precautions:

• Remove all power (AC and DC) before installing or removing any modules since damage to components

may occur if power remains applied.

• Circuit boards contain static-sensitive components. Always ground yourself with a proper wrist strap

before handling any boards so that static charges are removed from the body. Use static suppressive

packaging to protect electronic assemblies.

FFTReplacement

1. Make certain thatAC and DC power have been removed from the panel.

2. Unplug the terminal block connectors from TB1, TB2 and TB3 located on the top edge of the defective FFT board

(label to ensure reinstallation in correct positions).

3. Unplug the panel telephone handset from Phone Jack J1 located on bottom center of the defective FFT board.

4. Remove two mounting screws which hold the defective FFT board to the mounting bracket standoffs and set aside.

5. Carefully lift the defective FFT board from the slot in the bottom of the mounting bracket.

6. Remove the ribbon cable connectors from J2 on the right side of the board and J3 on the back of the defective FFT

board.

7. Connect cable between J2 on the new FFTboard and P5 on Zone Split Audio Panel main circuit board as illustrated

below.

8. If telephone call-ins are to be annunciated on the ZPM, connect cable between J3 on the FFT and P4 on the back

of the ZPM(K) module. Note that the J3 and P4 ribbon cable connectors are keyed to prevent incorrect

installation. Refer to following illustration for connector locations.

The FFTFire Fighter Telephone Module provides supervision,

annunciation and control for local and remote telephone handsets as

well as an optional remote microphone.

Audio Panel with Zone Split

Make certain that the ribbon cable is

installedwith thered stripeoriented

asillustrated below.

red stripe

Document 52246 RevA ECN 07-873 1/16/08

Standoff Standoff

Slot

Mounting Bracket

FFT

Terminal Block Connectors

J2 (on side)

TB1TB2TB3

J3 (on back)

RibbonCable

Connectors

SW1 J1

9. Insert the bottom of the new FFT board in the slot located in the bottom right of the mounting bracket as indi-

cated in illustration below.

10. Secure the module to the mounting bracket standoffs with the two mounting screws.

11. Wire the terminal blocks TB1,TB2 and TB3 as described in the illustration below. Plug the terminal block

connectors which were disconnected in step 2 into TB1, TB2 andTB3 located on the top edge of the FFT.

12. Plug the panel telephone handset into Phone Jack J1 on bottom center of FFT.

13. Set switch SW1 to correct position. SW1 positioned to the left (as illustrated below) indicates that the remote

microphone is installed. SW1 positioned to the right indicates that a remote microphone is not installed.

14. Set switch SW2 to correct position. SW2 positioned up (as illustrated below) indicates that the audio wiring to

the Remote Page Jack is configured for 2-wire Class B.

15. ReapplyAC and DC power

16. Program the host FACPfor proper operation with the Audio Panel

17. Test the panel for proper operation.

SW2

Table of contents

Other Honeywell Control Unit manuals

Honeywell

Honeywell PFA 700 Manual

Honeywell

Honeywell NetAXS User manual

Honeywell

Honeywell 7800 SERIES User manual

Honeywell

Honeywell VR8215S User manual

Honeywell

Honeywell XW100 User manual

Honeywell

Honeywell SK-Mon-10 User manual

Honeywell

Honeywell SV2 Series User manual

Honeywell

Honeywell VF5000 Series User manual

Honeywell

Honeywell L4017 User manual

Honeywell

Honeywell Braukmann FD300 User manual

Honeywell

Honeywell 4219 Assembly instructions

Honeywell

Honeywell RV277 User manual

Honeywell

Honeywell NetAXS-123 User manual

Honeywell

Honeywell ADEMCO 5800RL User manual

Honeywell

Honeywell BCU 460 Manual

Honeywell

Honeywell ERM5220R1018 User manual

Honeywell

Honeywell HM700AFVALVE User manual

Honeywell

Honeywell FF-SRE6029 User manual

Honeywell

Honeywell TR80 Installation guide

Honeywell

Honeywell S89C User manual

Honeywell

Honeywell N-1000 Service manual

Honeywell

Honeywell NK298S User manual

Honeywell

Honeywell SmartValve SV9520H User manual

Honeywell

Honeywell SUPER TRADELINE VR8300A User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual