Honeywell 4600g User manual
4600g, 4600r, 4600rp, 4800i
Quick Start Guide
1
Note: Refer to your user’s guide for information
about cleaning your device.
For localized language versions of this document,
go to www.honeywell.com/aidc.
Getting Started
Turn off computer’s power before connecting the
scanner, then power up the computer once the
scanner is fully connected.
USB Connection
2
Keyboard Wedge Connection
Serial (RS-232) Connection
3
Reading Techniques
The view finder
projects an aiming
beam that should
be centered over
the barcode, but
can be positioned
in any direction for
a good read.
Hold the scanner
over the barcode,
pull the trigger, and center the aiming beam on the
barcode.
The aiming beam is smaller when the scanner is
closer to the code and larger when it is farther from
the code. Hold the scanner close to smaller
barcodes, and farther away from large barcodes to
get a proper read.
If the barcode is highly reflective (e.g., laminated),
you may need to tilt the scanner at an angle so the
barcode can be scanned.
Standard Product Defaults
The following barcode resets all standard product
default settings.
Standard Product Defaults
4
Interface
Scan the barcode that describes the PC or interface
you are using.
AT/PS2 Keyboard Wedge
(Default)
RS-232
USB Keyboard (PC)
Emulate External Keyboard
Japan DOS/V
USB Japanese Keyboard (PC)
5
Keyboard Country
Scan the Program Keyboard Country barcode
below, then scan the numeric barcode(s) from
page 10, then the Save barcode to program the
keyboard for your country. As a general rule, the
following characters are not supported by the
scanner for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~.
Note: For a complete list of country codes, see the
User’s Guide for your product at our website,
www.honeywell.com/aidc.
Country Code Scan Country Code Scan
Belgium 1Italy 5
Denmark 8Norway 9
Finland 2Spain 10
France 3Switzerland 6
Germany/Austria 4USA (Default) 0
Great Britain 7
Program Keyboard Country
Save
6
Trigger
The following barcodes will allow you to use the
reader in Manual Trigger mode (need to press the
trigger to read) or Presentation mode (the reader is
activated when it “sees” a barcode).
Streaming Presentation™
Note: Streaming Presentation Mode applies only
to units with the Advanced Illumination
feature. Units with the advanced illumination
feature have a software revision of
31205480-118 or newer.
When in Streaming Presentation mode, the imager
leaves the scan illumination on all the time and
continuously searches for barcodes.
Manual Trigger
(Default)
Presentation Mode
Streaming Presentation Mode
7
Reread Delay
This sets the time period before the scanner can
read the
same
barcode a second time. Setting a
reread delay protects against accidental rereads of
the same barcode.
Suffix
If you want a carriage return after the barcode, scan
the Add CR Suffix barcode. To add a tab after the
barcode, scan the Add Tab Suffix barcode.
Otherwise, scan the Remove Suffix barcode to
remove the suffixes.
Medium Reread Delay
Add CR Suffix
Remove Suffix
Add Tab Suffix
8
Add Code ID Prefix to all Symbologies
Scan the following barcode if you wish to add a
Code ID prefix to all symbologies at once.
Note: For a complete list of Code IDs, see the
User’s Guide for your product at our website,
www.honeywell.com/aidc.
Function Code Transmit
When this selection is enabled and function codes
are contained within the scanned data, the imager
transmits the function code to the terminal. Charts
of these function codes are provided in your User’s
Guide. When the imager is in keyboard wedge
mode, the scan code is converted to a key code
before it is transmitted.
Add Code ID Prefix To All Symbologies
(Temporary)
Enable
(Default)
Disable
9
Data Format Editor Instructions
The following are abbreviated instructions for
entering a data format. For complete instructions
refer to your User’s Guide, available at our website,
www.honeywell.com/aidc.
1. Scan the Enter Data Format symbol.
2. Primary/Alternate Format: scan 0for Primary
Format
3. Terminal Type: scan 099 for any terminal type
4. Code I.D.: scan 99 for any barcode type
5. Length: scan 9999 for any length barcode.
6. Editor commands: use the Programming Chart
that follows.
7. Scan Save to save your entries.
Enter Data Format
Clear All Data Formats
Save
Other manuals for 4600g
2
This manual suits for next models
5
Table of contents
Other Honeywell Barcode Reader manuals
Honeywell
Honeywell Xenon CCB01-010BT-BF User manual
Honeywell
Honeywell Metrologic 3780 User manual
Honeywell
Honeywell VOYAGER 1202G BF User manual
Honeywell
Honeywell 4800i User manual
Honeywell
Honeywell 4800i User manual
Honeywell
Honeywell BTRS-QS User manual
Honeywell
Honeywell Fusion MS3780 User manual
Honeywell
Honeywell VOYAGER 1200G User manual
Honeywell
Honeywell 2020-5 User manual
Honeywell
Honeywell Xenon 1910 User manual
Honeywell
Honeywell 7120 Orbit User manual
Honeywell
Honeywell Virtuos 1D User manual
Honeywell
Honeywell Orbit MS7120 User manual
Honeywell
Honeywell QUANTUME IS3480 User manual
Honeywell
Honeywell Hyperion 1300G User manual
Honeywell
Honeywell 4820HDHM User manual
Honeywell
Honeywell VoyagerCG MS9540 User manual
Honeywell
Honeywell MS9520 Voyager User manual
Honeywell
Honeywell Orbit MS7120 User manual
Honeywell
Honeywell VoyagerGS MS9590i User manual
