Hobby King DH 82 Tiger Moth User manual
Assembly manual
For intermediate fliers
Specs
Wingspan: 912mm
Fuselage length: 772mm
Flying weight: 620-680g
Wing area: 24 2 dm²
Wing loading: 26g/dm²
Included in the box:
l Fuselage and battery canopy
l Motor and ESC
l Servos (pre-installed) x4
l Main wings x2
l Vertical stab
l Horizontal stab x2
l Engine cowling
l 10x4 7 slowfly prop and spinner
l Windshield x2
l Wire and wing members
l Scale landing gear
l Wheels x2
l Glue
l Pushrods
l Additional hardware (screws and
control horns)
Equipment required (not included):
l 4 channel radio and receiver
l Battery (3s 1300-1600mah)
l CA glue
l Drill with 2mm bit
l Small screwdrivers and Allen (hex)
keys
l Craft knife
l Scissors
Step 1: Gluing the tail
Take the vertical and horizontal stabs and glue to the fuselage as shown below
Note, make sure there is a small gap
(~1mm) between this portion of the
fuselage and the rudder after instillation,
to accommodate rudder travel
Step 2: inishing off the tail
First take two of the following control horns and enlarge one of the holes to 2mm I used the
second hole from the end, and suggest this as a starting point Moving inwards towards the base
will increase control surface throw while moving outwards will do the opposite In any case, make
sure that you use equivalent holes for both elevator surfaces
Now take the second type of control horn, together with the attached collet Check to make sure
that the collet is free to rotate on the horn If so, skip to the next step If not, remove the collet,
enlarge the diameter of the hole to 2 mm and reassemble using just one washer
Glue these in their respective locations as shown below You may use the glue provided or faster
drying glue as you wish Also glue the following two plastic parts in place Please note that these
are not identical (i e there is a left-hand side part and a right-hand side part Where each part goes
should be relatively obvious under closer inspection )
Step 3: Lower main wing and landing gear
Remove the paper from the aileron servo wires and feed these through the plane as shown
Aileron plug
Slot the wing in place There is no need to glue Next, take the landing gear and remove the
cable-tie holding it together (Note there are small pieces in the landing gear bag that will need to
be kept safe until later, do not lose these)! Place in the slot provided, making sure that the landing
gear is orientated in the correct manner as shown below Secure with the four screws provided Do
not over-tighten these!
Install the following two plastic parts as shown Not again that there is a LHS and an RHS part
Finally, attach control horns, pushrods and clevises tail and shown below
Blunt edge to the front,
sharp edge to the back
Step 4: Windshields
Cut out the windshields as below
Glue in place on the fuselage If you are not sure, the next image shows these in place
Step 5: Plastic support members
First take the longest of the support members There should be four of them provided with your
kit Glue in place as below Note the position of each of the pieces Again, none are identical so
take this into account The smooth side of each piece should face outwards
Flip the plane over and secure with the following plastic parts Again, note that these are not all
identical, but their correct locations should be fairly obvious
Flip the plane back over and install the final two plastic members These attach directly to the
fuselage
Smooth side
Note, this shaped
piece is to be glued
in position here
Attach the following piece as shown for detailed scale looks!
Here
Step 6: Upper main wing attachment
Glue the upper wing in place, atop the plastic parts previously put in
Next, support wires should be installed First, take one of the cables provided in your kit and tie a
knot in the end Secure with CA and trim
Now, examine the following image Make sure that your glue from step 5 is fully dry
Begin by feeding the cable through the hole labeled 1, then through 2 etc Note, at hole 4 feed the
cable through the rearmost hole and back through the frontmost hole After each pass through a
hole, secure in place using a drop of CA
Table of contents
Other Hobby King Toy manuals
Hobby King
Hobby King Maestro-46 User manual
Hobby King
Hobby King Angel 920 User manual
Hobby King
Hobby King Aether 3700 EP User manual
Hobby King
Hobby King EXTRA260P User manual
Hobby King
Hobby King Breeze User manual
Hobby King
Hobby King Tanager Glider User manual
Hobby King
Hobby King Waco SRE User manual
Hobby King
Hobby King Plug-N-Fly Paramotor User manual
Hobby King
Hobby King TRAINSTAR User manual
Hobby King
Hobby King Micro SU-27 User manual
Hobby King
Hobby King Decathlon User manual
Hobby King
Hobby King 450 User manual
Hobby King
Hobby King H-KING Cri Cri User manual
Hobby King
Hobby King Mariposa Trainer User manual
Hobby King
Hobby King FALCON TRAINER User manual
Hobby King
Hobby King Piper J3-120 cub User manual
Hobby King
Hobby King AT-6 Texan Instructions for use
Hobby King
Hobby King Mig-15 EDF User manual
Hobby King
Hobby King Fokker E.111 Fighter Aircraft User manual
Hobby King
Hobby King Ezio 1500 EP User manual
