Hitachi RAS-40CNH2 User manual

SPLIT TYPE

HITACHI

INDOOR UNIT/OUTDOOR UNIT

MODEL

RAS-40CNH2 / RAC-40CNH2

RAS-50CNH2 / RAC-50CNH2

OUTDOOR UNIT

INDOOR UNIT

Instruction manual Page 1~22

To obtain the best performance and ensure years of trouble

free use, please read this instruction manual completely.

Bedlenungsanleitung Suite 23~44

Bitte lesen Sie diese Bedienungsanleitung aufmerksam

durch, um durch richtige Bedienung jahrelangen und

störungsfreien Betrieb zu gewährleisten.

Mode d’emploi Page 45~66

Des performances optimales et un fonctionnement à long

terme seront assurés en appliquant les présentes

instructions après avoir entièrement lu ce mode d’emploi.

Manuale di istruzioni Pag. 67~88

Per garantire la migliore prestazione e la più lunga

durataleggere attentamente e al completo le seguanti

istruzioni.

RAC-40CNH2

RAC-50CNH2

Manual de instrucciones Página 89~110

Para obtener el mejor funcionamiento y asegurar años de

uso libre de problemas, lea cuidadosamente este manual

de instrucciones.

Manual de instruções Página 111~132

A fim de obter um bom funcionamento e de garantir uma

utilização sem falhas durante muitos anos, é favor ler este

manual de instruções completamente.

O‰ËÁ›Â˜ XÂÈÚÈÛÌÔ‡ ™ÂÏ›‰· 133~154

°È· ÙËÓ Î·Ï‡ÙÂÚË ‰˘Ó·Ù‹ ·ﬁ‰ÔÛË Î·È ÙËÓ Ì·ÎÚÔ¯ÚﬁÓÈ·

Î·È ¯ˆÚ›˜ ÚÔ‚Ï‹Ì·Ù· ¯Ú‹ÛË ÙË˜ Û˘ÛÎÂ˘‹˜ ·˘Ù‹˜,

·Ú·Î·ÏÔ‡ÌÂ ‰È·‚¿ÛÙÂ Ï‹Úˆ˜ ÙÈ˜ Ô‰ËÁ›Â˜ ¯ÂÈÚÈÛÌÔ‡ ÙË˜.

Инструкция по эксплуатации

стр. 155~176

Для обеспечения наилууших эксплуатационных

характеристик и многолетней бе отка ной работы

оборудования необходимо полностыо оэнакомиться с

данной Инструкцией по эксплуатации.

“BESTÄIGUNG” und “Bescheingung des Herstellers/Importeurs” sind am Ende dieser Bedienungsanleitung beschrieben.

RAS-40CNH2

RAS-50CNH2

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

(EN1) RAS/RAC-40/50CNH2 3/25/05, 2:361

–2 –

SAFETY PRECAUTION

●

Please read the “Safety Precaution”carefully before operating the unit to ensure correct usage of the unit.

●

Pay special attention to signs of “Warning”and “Caution”. The “Warning”section contains matters which,

if not observed strictly, may cause death or serious injury. The “Caution”section contains matters which may

result in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

●

The sign indicate the following meanings.

●

Please keep this manual after reading.

WARNING

PRECAUTIONS DURING INSTALLATION

●Do not reconstruct the unit.

Water leakage, fault, short circuit or fire may occur if you reconstruct

the unit by yourself.

●Please ask your sales agent or qualified technician for the installation

of your unit. Water leakage, short circuit or fire may occur if you install

the unit by yourself.

●Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor,

or the earth line of telephone. Improper installation of earth line may

cause electric shock.

●A circuit breaker should be installed depending on the mounting site of

the unit. Without a circuit breaker, the danger of electric shock exists.

●Do not install near location where there is flammable gas. The outdoor

unit may catch fire if flammable gas leaks around it.

●Please ensure smooth flow of water when installing the drain hose.

CAUTION

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

PRECAUTIONS DURING OPERATION

●Avoid an extended period of direct air flow for your health.

●Should abnormal situation arises (like burning smell), please stop operating the unit

and turn off the circuit breaker. Contact your agent. Fault, short circuit or fire may

occur if you continue to operate the unit under abnormal situation.

●Please contact your agent for maintenance. Improper self maintenance may cause

electric shock and fire.

●Please contact your agent if you need to remove and reinstall the unit. Electric

shock or fire may occur if you remove and reinstall the unit yourself improperly.

●Do not put objects like thin rods into the panel of blower and suction side

because the high-speed fan inside may cause danger.

●During thunder storm, disconnect and turn off the circuit breaker.

●Do not use any conductor as fuse wire, this could cause fatal accident.

Make sure to connect earth line.

Indicates the instructions that must be followed.

The sign in the figure indicates prohibition.

(EN1) RAS/RAC-40/50CNH2 3/25/05, 2:362

–3 –

ENGLISH

PRECAUTIONS DURING OPERATION

●Do not attempt to operate the unit with wet hands, this could cause fatal

accident.

●When operating the unit with burning equipments, regularly ventilate the

room to avoid oxygen insufficiency.

●Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus

such as the electric kettle, oven etc.

●Do not place plants directly under the air flow as it is bad for the plants.

●Please ensure that outdoor mounting frame is always stable, firm and

without defect. If not, the outdoor unit may collapse and cause danger.

●Do not splash or direct water to the body of the unit when cleaning it as this

may cause short circuit.

●When operating the unit with the door and windows opened, (the room humidity is always above

80%) and with the air deflector facing down or moving automatically for a long period of time,

water will condense on the air deflector and drips down occasionally. This will wet your furniture.

Therefore, do not operate under such condition for a long time.

●If the amount of heat in the room is above the cooling or heating capability of the unit (for

example: more people entering the room, using heating equipments and etc.), the preset room

temperature cannot be achieved.

●Do not climb on the outdoor unit or put objects on it.

●Please switch off the unit and turn off the circuit breaker during cleaning, the

high-speed fan inside the unit may cause danger.

●Turn off the circuit breaker if the unit is not to be operated for a long period.

●The product shall be operated under the manufacturer specification and

not for any other intended use.

●Do not put water container (like vase) on the indoor unit to avoid water

dripping into the unit. Dripping water will damage the insulator inside the unit

and causes short-circuit.

(EN1) RAS/RAC-40/50CNH2 3/25/05, 2:363

–4 –

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

INDOOR UNIT

OUTDOOR UNIT

WIDTH (mm)

798

850

MODEL

RAS-40CNH2, RAS-50CNH2

RAC-40CNH2, RAC-50CNH2

HEIGHT (mm)

285

650

DEPTH (mm)

183

298

MODEL NAME AND DIMENSIONS

NAMES AND FUNCTIONS OF EACH PART

Air filter

To prevent dust from coming into the indoor unit.

(Refer page 18)

Front panel

Indoor unit indicators

Light indicator showing the operating condition.

(Refer page 5)

Horizontal deflector ●Vertical deflector

(Air Outlet)

(Refer page 16)

Remote controller

Send out operation signal to the indoor unit. So as to

operate the whole unit.

(Refer page 6)

Drain pipe

Condensed water drain to outside.

Connecting cord and insulation pipe for piping

Air inlet (Back, Left and Right side)

Air outlet

In relation to outdoor unit

•Even if operation stops, fan is running

for 10 to 60 seconds to reduce heat

of electric components.

CAUTION

•When heating operation, drain or

defrosted water flows out from outdoor

unit. Don’t stop drain outlet portion in

chilly area so as not to freeze these.

(EN1) RAS/RAC-40/50CNH2 3/25/05, 2:364

–5 –

ENGLISH

INDOOR UNIT INDICATORS

OPERATION LAMP

This lamp lights during operation.

The OPERATION LAMP flashes in the following cases

during heating.

(1) During preheating

For about 2–3 minutes after starting up.

(2) During defrosting

Defrosting will be performed about once an hour

when frost forms on the heat exchanger of the

outdoor unit, for 5–10 minutes each time.

FILTER LAMP

When the device is operated for a total of about 100

hours, the FILTER lamp lights to indicate that it is time

to clean the filter. The lamp goes out when the FILTER

LAMP RESET SWITCH is pushed.

TIMER LAMP

This lamp lights when the timer is working.

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

HITACHI

OPERATION INDICATOR

●This figure shows the opening condition of

front panel. Refer to page 18 in relation to

how to open or close the front panel.

AUTO

RESTART

SWITCH

POWER SWITCH

FILTER LAMP RESET SWITCH

After cleaning filters, please

push it.

AUTO

RESTART

SWITCH

AUTO RESTART SWITCH

●In the event of power failure, the air conditioner will restart automatically in the previously selected mode

once the power is restored.

●In the event of power failure during TIMER operation, the timer will be reset and the unit will stop

operating.

(EN1) RAS/RAC-40/50CNH2 3/25/05, 2:365

–6 –

AUTO

HEAT

DEHUMIDIFY

COOL

FAN

FAN SPEED

LOW

MED

SLEEPING

STOP (CANCEL)

START (RESERVE)

START/STOP

TIME

TIMER SET

TIMER SELECTOR

ON TIMER

OFF TIMER

AUTO SWING

RESET

NAMES AND FUNCTIONS OF EACH PART

REMOTE CONTROLLER

This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting

is controlled electronically, the range of control may be shorter.

This unit can be fixed on a wall using the fixture provided. Before fixing it, make sure the indoor unit can

be controlled from the remote controller.

●Signal emitting window/transmission sign

Point this window toward the indoor unit when controlling it.

The transmission sign blinks when a signal is sent.

●Display

This indicates the room temperature selected, current time, timer status,

function and intensity of circulation selected.

●START/STOP button

Press this button to start operation. Press it again to stop operation.

●SLEEP button

Use this button to set the sleep timer.

●TEMPERATURE buttons

Use these buttons to raise or lower the temperature setting. (Keep pressed,

and the value will change more quickly.)

●TIME button

Use this button to set and check the time and date.

●RESET buttons

●FUNCTION selector

Use this button to select the operating mode. Every time you press it,

the mode will change from (AUTO) to (HEAT) to (DEHUMIDIFY) to

(COOL) and to (FAN) cyclically.

●FAN SPEED selector

This determines the fan speed. Every time you press this button, the intensity

of circulation will change from (AUTO) to (HI) to (MED) to (LOW)

(during the (FAN) mode, from HI to MED to LOW).

●AUTO SWING button

Controls the angle of the horizontal air deflector.

●TIMER control

Use this button to set the timer.

●OFF-TIMER button Select the turn OFF time.

●ON-TIMER button Select the turn ON time.

●RESERVE button Time setting reservation.

●CANCEL button Cancel time reservation.

Precautions for Use

●Do not put the remote controller in the following places.

●In direct sunlight.

●In the vicinity of a heater.

●Handle the remote controller carefully. Do not drop it on the floor,

and protect it from water.

●Once the outdoor unit stops, it will not restart for about 3 minutes

(unless you turn the power switch off and on or unplug the power

cord and plug it in again).

This is to protect the device and does not indicate a failure.

●If you press the FUNCTION selector button during operation, the

device may stop for about 3 minutes for protection.

(EN1) RAS/RAC-40/50CNH2 3/25/05, 2:366

–7 –

ENGLISH

AUTOMATIC OPERATION

The device will automatically determine the mode of operation, HEAT or COOL, depending on the initial room

temperature. The selected mode of operation will not change when the room temperature varies.

■As the settings are stored in memory in the remote controller, you only have

to press the (START/STOP) button next time.

Press the FUNCTION selector so that the display indicates the (AUTO)

mode of operation.

●When AUTO has been selected, the device will automatically determine

the mode of operation, HEAT or COOL, depending on the current

room temperature.

●When AUTO is first selected, the device will determines the current

room temperature and accordingly selects the proper operation mode.

●When the air conditioner has adjusted the room’s temperature to the

near preset temperature, it will begin monitor operation. If the room

temperature subsequently changes, the air conditioner will once again

select the appropriate operation (heating or cooling) to adjust the

temperature to the preset temperature. The monitoring operation range

is ±3°C relative to the preset temperature.

●If the mode automatically selected by the unit is not satisfactory,

manually change the mode setting (heat, dehumidify, cool or fan).

●When AUTO has been selected, the device will automatically determine

the mode of operation, HEAT, COOL or Dehumidify, depending on the

current room temperature and outdoor temperature.

Press the (START/STOP) button.

Operation starts with a beep.

Press the button again to stop operation.

You can raise or lower the temperature setting as necessary by maximum of

3°C.

Press the temperature button and the temperature setting

will change by 1°C each time.

●The preset temperature and the actual room temperature may vary

somewhat depending on conditions.

●The display does not indicate the preset temperature in the AUTO mode.

If you change the setting, the indoor unit will produce a beep.

START

STOP

Press the (FAN SPEED) button, AUTO and LOW is available.

°C

RESET

(EN1) RAS/RAC-40/50CNH2 3/25/05, 2:367

–8 –

HEATING OPERATION

●Use the device for heating when the outdoor temperature is under 21°C.

When it is too warm (over 21°C), the heating function may not work in order to protect the device.

●In order to keep reliability of the device, please use this device above -15°C of the outdoor temperature.

Press the FUNCTION selector so that the display indicates

(HEAT).

Set the desired FAN SPEED with the (FAN SPEED) button

(the display indicates the setting).

(AUTO): The fan speed changes automatically according

to the temperature of the air which blows out.

(HI) : Economical as the room will become warm

quickly.

But you may feel a chill at the beginning.

(MED) : Quiet.

(LOW) : More quiet.

Set the desired room temperature with the TEMPERATURE

buttons (the display indicates the setting).

The range of 18-22°C is recommended as the

room temperature for heating.

If the temperature setting is 20°C, the room

temperature will be controlled at around 20°C.

The temperature setting and the actual room temperature may

vary somewhat depending on conditions.

Press the (START/STOP) button. Heating operation starts

with a beep. Press the button again to stop operation.

■As the settings are stored in memory in the remote controller, you only

have to press the (START/STOP) button next time.

However, if operation stops with fan speed of “LOW”, fan speed is

automatically set to “AUTO”next time.

START

STOP

˚C

RESET

˚C

(EN1) RAS/RAC-40/50CNH2 3/25/05, 2:368

–9 –

ENGLISH

DEHUMIDIFYING OPERATION

Use the device for dehumidifying when the room temperature is over 16°C.

When it is under 15°C, the dehumidifying function will not work.

■When you want to change the operation mode, please use the FUNCTION

selector.

■Set the desired temperature is available.

■You also can use the FUNCTION selector to select this operation.

■When dehumidifying is done using the (DEHUMIDIFY) button, the ON/

OFF timer cannot be used.

If the ON/OFF timer has been set, and the (DEHUMIDIFY) button is

pressed, the setting of the ON/OFF timer will be canceled.

■If you wish to use the ON/OFF timer, perform the dehumidifying operation

using the FUNCTION selector.

■When dehumidifying is done using the (DEHUMIDIFY) button, the set

time on the SLEEP timer can be changed using the SLEEP TIMER button.

Press the (DEHUMIDIFY) button.

Operation start with a beep.

The FAN SPEED is set at LOW automatically.

The FAN SPEED button does not work.

Press the (START/STOP) button.

STOP

■Dehumidifying Function

When the room temperature is higher than the temperature setting: The device will dehumidify the room,

reducing the room temperature to the preset level.

When the room temperature is lower than the temperature setting: Dehumidifying will be performed with the

room temperature set slightly lower than the current room temperature, whatever the temperature setting. The

function will stop (the indoor unit will stop emitting air) as soon as the room temperature becomes lower than

the setting.

RESET

˚C

(EN1) RAS/RAC-40/50CNH2 3/25/05, 2:369

– 10 –

COOLING OPERATION

Use the device for cooling when the outdoor temperature is 22-42°C.

If humidity is very high (over 80%) indoors, some dew may form on the air outlet grille of the indoor

unit.

Press the FUNCTION selector so that the display indicates

(COOL).

Set the desired FAN SPEED with the (FAN SPEED) button

(the display indicates the setting).

(AUTO): The FAN SPEED is HI at first and varies to

MED automatically when the preset temperature

has been reached.

(HI) : Economical as the room will become cool

quickly.

(MED) : Quiet.

(LOW) : More quiet.

Set the desired room temperature with the TEMPERATURE

buttons (the display indicates the setting).

The range of 25-28°C is recommended as the

room temperature for cooling.

If the temperature setting is 27°C, the room

temperature will be controlled at around 27°C.

The temperature setting and the actual room temperature may

vary somewhat depending on conditions.

Press the (START/STOP) button. Cooling operation starts

with a beep. Press the button again to stop operation. The

cooling function does not start if the temperature setting is

higher than the current room temperature (even though the

(OPERATION) lamp lights). The cooling function will start

as soon as you set the temperature below the current room

temperature.

■As the settings are stored in memory in the remote controller, you only

have to press the (START/STOP) button next time.

However, if operation stops with fan speed of “LOW”, fan speed is

automatically set to “AUTO” next time.

START

STOP

RESET

(EN2) RAS/RAC-40/50CHN2 3/25/05, 2:3810

This manual suits for next models

Table of contents

Other Hitachi Air Conditioner manuals

Hitachi

Hitachi RAS-5HVRNM1E User manual

Hitachi

Hitachi RAS-18C9 User manual

Hitachi

Hitachi DXF-2.0A1 Instruction Manual

Hitachi

Hitachi RAS-12-HNP User manual

Hitachi

Hitachi RAK-65NH5 User manual

Hitachi

Hitachi RAM-130QH5 User manual

Hitachi

Hitachi RAS-50WX8 User manual

Hitachi

Hitachi RAC-25WXE User manual

Hitachi

Hitachi RAS-E14H2A User manual

Hitachi

Hitachi RAC-18EH2 User manual

Hitachi

Hitachi RAC-32CNH2 User manual

Hitachi

Hitachi RAS-3HVRNM2 Instruction Manual

Hitachi

Hitachi RAC-S28H2 User manual

Hitachi

Hitachi airHome 400 User manual

Hitachi

Hitachi UTOPIA RAS-3HVRC2 User manual

Hitachi

Hitachi RAF25NH4 User manual

Hitachi

Hitachi RAS-E10HA User manual

Hitachi

Hitachi airHome 600 User manual

Hitachi

Hitachi RCIM-FSN2 User manual

Hitachi

Hitachi RAS-18GH5 User manual

Hitachi

Hitachi RAS-S10CJT User manual

Hitachi

Hitachi air Home Ducted RAD-DJ50QHAE User manual

Hitachi

Hitachi RAK-35PEC User manual

Hitachi

Hitachi RAS-X13CXT User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual

Webasto

Webasto Frigo Top 25 DS Instructions for use