Heat Controller PTAC09A130A User manual

Heat Controller • 1900 Wellworth Ave. • Jackson, MI 49203 • (517)787-2100 • www.heatcontroller.com

OWNER’S MANUAL

Packaged Terminal

Air Conditioners & Heat Pumps

7,000-15,000 BTUH

Cooling with Electric Heat

PTAC07A130A

PTAC09A130A

PTAC12A130A

PTAC12A150A

PTAC15A150A

PTAC15A130A

Heat Pump with Electric Heat

PTHP07A130A

PTHP09A130A

PTHP12A130A

PTHP12A150A

PTHP15A150A

PTHP15A130A

THE FOLLOWING WARNINGS ARE

VERY IMPORTANT FOR SAFETY.

PLEASE READ THEM CAREFULLY

BEFORE INSTALLATION!

1. This air conditioner must be installed by a

certicated installer.

2. Please insure that there is an available ground in

the power supply system before installation.

3. To avoid electric shock or death, the socket

or terminal blocks for power supply to the air

conditioner(include 277V and 115V and 208-230V

series and the units that have LCDI power cord)

must have a Ground Fault Circuit Interrupter.

4. During installation, do not cross connect or reverse

L1 and neutral. Please be sure the ground wire is

rmly connected otherwise it is possible to result in

electrical shock or death.

RECOGNIZE THIS SYMBOL

AS A SAFETY PRECAUTION

WARNING

THE MANUFACTURER WILL NOT BE RESPONSIBLE

FOR ANY INJURY OR PROPERTY, DAMAGE

ARISING FROM IMPROPER SERVICE OR

SERVICE PROCEDURES. IF YOU INSTALL OR

PERFORM SERVICE ON THIS UNIT, YOU ASSUME

RESPONSIBILITY FOR ANY PERSONAL INJURY OR

PROPERTY DAMAGE WHICH MAY RESULT, MANY

JURISDICTIONS REQUIRE A LICENSE TO INSTALL

OR SERVICE HEATING AND AIR CONDITIONING

EQUIPMENT.

WARNING

HIGH VOLTAGE

DISCONNECT ALL POWER BEFORE

SERVICING OR INSTALLING THIS UNIT.

MULTIPLE POWER SOURCES MAY BE PRESENT,

FAILURE TO DO SO MAY CAUSE PROPERTY

DAMAGE, PERSONAL INJURY OR DEATH

PACKAGED TERMINAL A/C OWNER’S MANUAL Heat Controller

CONTENTS

UNIT FEATURES ...................................................... 2

INSTALLATION INSTRUCTION................................ 4

WIRING ..................................................................... 8

OPERATING INSTRUCTIONS

(Accessory Optional). ................................................ 9

MAINTENANCE AND CLEANING............................11

NORMAL OPERATING SOUNDS

AND CONDITION.................................................... 13

DIAGNOSTIC CODES ............................................ 13

TROUBLE SHOOTING ........................................... 14

IMPORTANT NOTES:

Before using this manual, check the serial plate for

proper model identication.

The installation and servicing of this equipment must

be performed by qualied,experienced technicians

only.

Due to policy of continual product improvement, the

right is reserved to change specications and design

without notice.

IMPORTANT NOTE TO THE OWNER

The service portion of this manual is to be used by

qualied,professionally trained HVAC technicians

only. The manufacturer does not assume any

responsibility for property damage or personal injury

for proper service procedures or services performed

by an unqualied person.

IMPORTANT NOTE TO THE SERVICER

Read this manual and familiarize yourself with the

specic items which must be adhered to before

attempting to service this unit. The precautions

listed in this Installation Manual are intended as

supplemental to existing practices. However, if there

is a direct conict between existing practices and the

content of this manual, the precautions listed here

take precedence.

Heat Controller OWNER’S MANUAL Packaged Terminal A/C

UNIT FEATURES

This unit has many features which are different than

those found on conventional PTAC units. The servicer

must be familiar with these features in order to

property handle the unit.

• LCDI Cords - Underwriters Laboratories and the

National Electric Code (NEC) now require power

cords that sense current leakage and can open

the electrical circuit to the unit on units rated at

250 volts or less. In the event that unit does not

operate,check the reset button located on or near

the head of the power cord as part of the normal

troubleshooting procedure.

LCDI power Cord

• Automatic 3-minute compressor lockout - After

the compressor cycles off, it will not restart for three

minutes.

• Random restart delay - To help eliminate power

surges after a power outage, the unit Is equipped

with a two to four minute random restart delay

feature. Whenever the unit is plugged In with the

master switch turned on and the mode switch set in

the cool or heat mode, a random restart will occur.

• Indication LEDs - The control panel has LEDs that

correspond to fan operation and to Indicate unit

status. The LEDs next to the selections ON/OFF,

FAN, COOL, and HEAT indicate which operational

mode Is active.

• High Pressure Protection - The unit will shut off

automatically when the pressure in the system

is over 638 psi and within 10 minutes, after the

compressor turns off, the unit will restart when the

pressure turns back below 551 psi. This protection

can effectively avoid the burst and leakage of pipes,

lessen the system failures and prolong the service

life.

• Failure Tolerance - If the unit is in protection mode

less than 4 times in one hour, the accumulation

times will reset to avoid system failure. Only when

the unit enters protection mode more than 4 times in

one hour will the system fail to restart automatically

and need manual restart.

• Standard Physical Dimensions - The series PTAC

uses standard dimensions, 42” wide x 16” high x

13-3/4” deep.

Replacement of older units is made easy.

• Weather - Protected Electrical Components

-Vital electrical components are protected from the

weather by locating them on the indoor side of the

weather barrier.

• Highly Featured Microprocessor Controls

- Microprocessor controls are programmed to

interface with the temperature sensors to maximize

comfort conditions for the room occupant.

Thermistors are used to sense small changes in

temperature to give excellent room control and

allow the microprocessor to monitor and react to

changing conditions.

• Automatic Emergency Heat on Heat Pump

Units-Automatically uses electric resistance heat if

the heat pump falls.

• High-Temperature Heat Pump Operation

Protection

-Automatically protects the compressor if heat pump

is operated with high indoor coil temperatures.

Power to the outdoor fan and the compressor

are turned off if the indoor coil gets too hot during

heat pump operation to prevent damage to the

compressor.

PACKAGED TERMINAL A/C OWNER’S MANUAL Heat Controller

• Fan Motors Permanently Lubricated - All units

have two fan motors for quiet operation and

maximum operating efciency.

Motors are permanently lubricated to reduce

maintenance and totally enclosed to keep dirt and

water out of the motor windings.

• Indoor Fan Speed Selections LOW /HIGH/AUTO

- Unit may be operated in low, high or auto fan

speeds. Some speeds may not be present based

on unit capacities.

• Rotary Compressor - smoother operation for quiet,

dependable service and high efciency.

• Indoor Coil Frost Control - prevents indoor coil

from freezing. Frost can form on the Indoor coil

when the unit is operated in cooling when the

outdoor temperature is low. The unit automatically

shuts the compressor off until the indoor coil

temperature warms to the point where frosting will

no longer occur, then restarts the compressor.

• LS Control (front-desk control) - The unit can

be turned ON/OFF by a front desk control switch.

The control wire, colored purple, locates in the wall

mounted thermostat interface (refer to Fig. 7 on

page 8).

The control logic as belows:

1. Turn ON unit: short circuit R and LS then release

one time within 5 seconds.

2. Turn OFF unit: short circuit R and LS then release

for twice within 5 seconds.

3. Force unit shut down for one time: connect LS to R

for over 5 seconds and then release.

NOTE: After force shut down, you can turn the unit

ON again by hand-held remote controller or the

control panel.

• Special control functions for DIP switches - The

DIP switches are on main board. No. 5 auto

heating (for units with heat). When unit is connected

to the power supply, and room temperature Is

lower than 10°C/50°F for 3 minutes, unit will start

heating automatically no matter what the setting

mode is. Only when room temperature reaches

13°C/55°F will heating stop.

ON position enables this function.

No. 6 -Electric Power-off Memory. After power on,

the unit will run the same settings as last time.

ON position enables this function.

No. 7-Fan CON/CYC for heating.

ON position enables continuous fan for heating. The

default setting Is fan cycled for heating.

No. 8 -Fan CYC/CON for cooling ON position

enables fan cycle for cooling. The default setting is

fan continuous for cooling.

WARNING: Before service, you must disconnect

the power cord to avoid electric shock! Do not

reprogram DIP switches No. 1 to No. 4, when

powered this could cause damage or re. Power the

unit on again, the new function will be activated.

UNIT ACCESSORIES

This unit is designed for through-the-wall installation

in new or existing buildings. To complete the

installation of this PTAC, an insulated wall sleeve and

an outdoor grille (either the stamped aluminum

grille, or the architectural grille) are required.

Consult with your distributor to acquire any optional

accessories.

The chassis and the cabinet front are shipped in one

carton.

WARNING

HIGH VOLTAGE

DISCONNECT ALL POWER BEFORE SERVICING

OR INSTALLING THIS UNIT. MULTIPLE POWER

SOURCES MAY BE PRESENT,FAILURE TO DO SO

MAY CAUSE PROPERTY DAMAGE,PERSONAL

INJURY OR DEATH.

Heat Controller OWNER’S MANUAL Packaged Terminal A/C

SLEEVE INSTALLATION

Wall sleeve location

When making the wall opening, please observe the following requirements:

A) The air inlet and outlet should be unblocked so the air can be delivered to every corner of the room.

B) Install the unit in places that are away from heat or sources of ammable gases.

C) Do not install the unit in places that are subject to heavy dust.

D) Do not install the unit in places where the operational noise and exhausted air might trouble your neighbor.

E) There should be sufcient space around the unit to facilitate maintenance and repairs

(refer to Figs. 1 and 2).

INSTALLATION INSTRUCTIONS

To ensure that the unit operates safely and efciently, it must be installed, operated and maintained according

to these installation and operating instructions and all local codes and ordinances or,in their absence, with the

latest edition of the National Electric Code (or CEC for Canadian Installations). The proper installation of this

unit is described in the following sections. Following the steps in the order presented should ensure proper

installation.

WARNING

HIGH VOLTAGE

DISCONNECT ALL POWER BEFORE SERVICING

OR INSTALLING THIS UNIT. MULTIPLE POWER

SOURCES MAY BE PRESENT, FAILURE TO

DO SO MAY CAUSE PROPERTY DAMAGE,

PERSONAL INJURY OR DEATH.

Dimension Recommended installation clearance

D1 Projection of case into room - 1/2” minimum up to 1-3/4”

maximum without use of electrical sub-base.

Note: 2-3/8” minimum when sub-base is used.

D2 Height above nished oor or top of carpet - 1/2” minimum

2” recommended without sub-base - 3” minimum with sub-base.

Fig. 1 Fig. 2

WARNING

REMOVE FRONT PANEL, DO NOT DIRECTLY

TOUCH THE FIN.

OUTDOOR GRILLE

(OPTIONAL ACCESSORY)

An outside grille must be Installed to direct air ow for

proper unit operation and also protect the outdoor

coil. The grille must be installed before installing

the chassis. When replacing an old chassis with an

existing grille or using a specialized grille In a new

Installation, please check with after-sales engineer

of supplier to determine if the new chassis should

be used with the nonstandard specialized grille.

An improper outdoor grille can decrease cooling or

heating capacity,increase energy usage and shorten

compressor life and possibly void the warranty.

PACKAGED TERMINAL A/C OWNER’S MANUAL Heat Controller

Preparation of the Wall

The sleeve should be installed during construction

and lintels should be used to support the block above

the wall sleeve. The sleeve can not support the load

of bricks/ blocks.

For existing construction, wall opening must be

created,the proper dimensions are necessary to

avoid use of llers or additional framing .The sleeve is

modular in height and width (refer to Fig. 3 & Chart 2).

Height:

Fits 2 courses concrete block

Fits 6 courses standard brick

Fits 5 courses jumbo brick

Width: Fit approximately 3 stud spaces.

In order for condensate water to drain property inside

the unit, the sleeve must be installed properly:

• Level from right to left.

• A slight downward pitch from the indoor side to the

outdoor side as shown below Fig. 4).

• Fasten the wall sleeve (Fig. 5).

STAMPED ALUMINUM GRILLE

ARCHITECTURAL GRILLE

Fig. 5

Fig. 3

Fig. 4 Proper Sleeve Tilt

Minimum Finished

Opening Dimensions Approximate Sleeve Dimensions

Height Width Height Width Depth

16-1/4” 42-1/2” 16” 42” 13-3/4”

Note: Sleeves may vary be slightly manufacturer.

Ensure that the unit ts the sleeve before installation.

Chart 2

Heat Controller OWNER’S MaNual Packaged Terminal

CHASSIS INSTALLATION

1. Remove the cabinet front from the chassis as

described In Front Removal.

2. Insert the chassis into the wall sleeve.

IMPORTANT NOTES:

1. The unit is equipped with a rubber grommet

mounted compressor. These grommets are factory

set and require no adjustment.

2. Check the indoor and outdoor grilles for

obstructions to air ow. The unit must be located

where curtains, furniture, trees, or other objects do

not block the air ow to and from the unit. If air is

obstructed and/or deected back into the unit,the

air conditioner compressor may cycle on and off

rapidly. This could damage the compressor or

possibly void the warranty.

FRONT REMOVAL

1. Grasp the cabinet front.

3. Slide the chassis into the wall sleeve until the

chassis anges contact the front edge of the wall

sleeve.

4. Secure the chassis to the wall sleeve using two

screws on each side of the chassis to ensure a

proper seal between the chassis and the wall

sleeve. The screws are supplied in a plastic bag.

Chassis Installation View 2

Chassis Installation View 1

3. Lift the cabinet front off the chassis. Reverse this

procedure to reinstall the cabinet front.

Cabinet Front Removal View 2

2. Pull the bottom of the cabinet front away from

the chassis until the retaining clips disengage.

Cabinet Front Removal View 1

Screws

(2 on each

side of unit)

PACKAGED TERMINAL OWNER’S MaNual Heat Controller

WIRING

Cord connection to a wall socket is not permitted for

265V units. All 265V units must be hard wired using

the hard wire kit or make use of the plug in receptacle

in the standard subbase.

230~208V units are equipped with LCDI power cords

and can open the electrical circuit to the unit. In

the event the unit does not operate, check the reset

button located on or near the head of the power cord

as part of the normal procedure.

VOLTAGE MEASUREMENTS

Once the unit is properly wired, measure the unit

supply voltage. Voltage must fall within the voltage

range given in Chart 3.

Fig. 6 Receptacles / Sub-bases

NOTE: See the “Remote Thermostat Change”

Instructions before using the thermostat.

Fig. 7 wall mounted thermostat wiring

Operating Voltage

Unit Voltage Voltage Utilization Range

Rating Minimum Minimum

230/208 187 253

265 238 292

Chart 3 - Operating Voltage

WARNING

HIGH VOLTAGE

DISCONNECT ALL POWER BEFORE SERVICING OR

INSTALLING THIS UNIT MULTIPLE POWER SOURCES BE

PRESENT, FAILURE TO DO SO MAY CAUSE PROPERTY

DAMAGE, PERSONAL INJURY OR DEATH.

DO NOT SERVICE THIS UNIT WITHOUT FIRST SHUTTING

OFF THE POWER TO THE UNIT FROM THE CIRCUIT

BREAKER AND/OR REMOVING THE UNIT CORD SET PLUG

FROM THE WALL OUTLET.

WARNING

TO AVOID THE RISK OF PROPERTY DAMAGE, PERSONAL

INJURY OR FIRE, USE ONLY COPPER CONDUCTORS.

WARNING

TO AVOID THE RISK OF PROPERTY DAMAGE, PERSONAL

INJURY OR DEATH DUE TO ELECTRICAL SHOCK, DO NOT

USE AN EXTENSION CORD WITH THIS UNIT.

WARNING

TO AVOID THE RISK OF PROPERTY DAMAGE, PERSONAL

INJURY OR FIRE. DO NOT INSTALL WITH POWER CORD

STRETCHED OR UNDER A STRAIN AS THIS MAY CREATE

LOOSE PLUG/RECEPTACLE CONNECTION.

WARNING

TO AVOID THE RISK OF PERSONAL INJURY, WIRING TO THE

UNIT MUST BE PROPERLY POLARIZED AND GROUNDED.

WARNING

THIS AIR CONDITIONER IS NOT MEANT TO PROVIDE

UNATTENDED COOLING OR LIFE SUPPORT FOR PERSONS

OR ANIMALS WHO ARE UNABLE REACT TO THE FAILURE

OF THIS PRODUCT.

THE FAILURE OF AN UNATTENDED AIR CONDITIONER MAY

RESULT IN EXTREME HEAT IN THE CONDITIONED SPACE

CAUSING OVERHEATING OR DEATH TO PERSONS OR

ANIMALS.

265V 30 Amp

265V 20 Amp

Large tandem

230/208V 30 Amp

Perpendicular

230/208V 20 Amp

Thermostat

Heat Controller OWNER’S MaNual Packaged Terminal

Receiver of IR remote controller signal

Fig. 8 Use of unit mounted control panel

Operation mode buttons

Press these buttons to select

the unit mode heat, cool or

fan.

Operation mode

indicator lamps

When the unit operates on

heat or cool or fan mode

the indicator lamps will be

activated.

Digital Displayer

On normal operation indicates room temperature;

When pressing + or - button, indicates setting temperature;

On time operation, indicates timer time;

On failure operation, indicates fault code.

COOL button

Press this button to set room

temperature cooler.

Warm button

Press this button to set room

temperature warmer.

ON/OFF button

Press this button to turn

the unit ON or OFF.

Operation indicator

lamp.

Fan speed indicator lamp.

Fan Speed button

Press this button to

select the fan speed on

high, low or auto.

OPERATING INSTRUCTIONS

PACKAGED TERMINAL OWNER’S MaNual Heat Controller

COOL / FAN / HEAT MODE

OPERATION PROCEDURE

Control panel:

• Press the ON/OFF button.

• Press the HEAT/COOL/FAN button, select the

operation mode: heat/cool/fan.

• Press + or - button, to set your desired temperature.

The setting temperature range is 60-90°F (16-32°C).

• Press the FAN SPEED button, to set your desired

air ow rate: high/low/auto.

TIMER PROCEDURE (Remote controller)

When batteries are inserted, the present time Is

automatically set to AM 0:00.E.X.:set to AM10:30.

• Open the back cover,push the CLK button .The time

Indicator is ickering and can set the present time.

• Press the HOUR button.(set to AM 10:00)

• Press the MIN button. (set to 30)

• Press the CLK button again, and then close the back cover.

SET UP OPERATION

1) Temperature shift key: Press + and - button at the

same time for 3 seconds, the temperature is shifted

between Fahrenheit and centigrade.

2) Temperature setting limiting: Press + and SPEED

button at the same time to enter the maximum

and minimum temperature setting. R1~R8 will be

displayed every 3 seconds. Release the two keys

to ensure the setting is effective and the gures will

last for 5 seconds. The temperature setting range

is between so 60°F ~90°F as factory default.

VENTILATION CONTROL

The ventilation control lever is located at left side of

unit, behind front panel.

NOTE: The vent door shipping tape must be removed

before using vent control lever. See Fig. 9 and Fig. 10.

When set to closed, only the air Inside the room is

circulated and ltered;

When set to open, some outdoor air will be drawn into

room, this will reduce heating or cooling efciency.

3) Remote thermostat change: In standby off

mode, press HEAT and+ button, for 3 seconds,

the buzzer will chime and LED display will read “P”

or “r”.

P: unit control panel has control of unit.

r: wall thermostat has control of unit.

R1 R2 R3 R4 R5 R6 R7 R8

Heating Temperature Limits (°F)

86 86 90 74 92 90 72 90

Cooling Temperature Limits (°F)

63 65 72 72 67 69 68 60

Chart 4. Temperature setting limiting

Fig. 10 Shipping Screw Location

Fig. 9 Shipping Tape Location

The vent control allows outside air to be drawn into the

conditioned area. This outside air can provide ventilation

when the blower Is operating, but it will increase the

heating or cooling load and operating costs.

To obtain access to the vent control

1. Remove the cabinet front (see Front Removal).

2. Remove the shipping screw (if installed) from the

vent door.

3.Remove the label (if present) from over the vent

control lever on the left side of the chassis. Remove

the vent door shipping screw.

4. Rotate the vent control lever to either open or close

the damper.

Shipping tape

Remove shipping

screw if present

This manual suits for next models

Table of contents

Other Heat Controller Air Conditioner manuals

Heat Controller

Heat Controller COMFORT AIRE RADS-51B Building instructions

Heat Controller

Heat Controller Century Installation guide

Heat Controller

Heat Controller BG-81J User manual

Heat Controller

Heat Controller DMC24CA-1 User manual

Heat Controller

Heat Controller REG-81G User manual

Heat Controller

Heat Controller CD-101G User manual

Heat Controller

Heat Controller DMC24DB-1 User manual

Heat Controller

Heat Controller RSE1318-1A User manual

Heat Controller

Heat Controller Comfort-Aire RG-51B User manual

Heat Controller

Heat Controller BG-81J User manual

Heat Controller

Heat Controller Comfort-Aire BG-123A User manual

Heat Controller

Heat Controller BGE H-Series Application guide

Heat Controller

Heat Controller Comfort-Aire BDE-103-A User manual

Heat Controller

Heat Controller EKTC07-1G User manual

Heat Controller

Heat Controller VMC09SB-1 Service User manual

Heat Controller

Heat Controller DMC24CA-1 User manual

Heat Controller

Heat Controller Comfort-Aire RAD-61A Building instructions

Heat Controller

Heat Controller PE-121A User manual

Heat Controller

Heat Controller Comfort-Aire BG-101A User manual

Heat Controller

Heat Controller PTAC07A130A User manual

Heat Controller

Heat Controller SMA 09 Manual

Heat Controller

Heat Controller PD-91B User manual

Heat Controller

Heat Controller COMFORT-AIRE RG-51-5 User manual

Heat Controller

Heat Controller B-MMC09FA-1 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual