Hayward Salt & Swim Datasheet

Salt & SwimTM Installation Quick Start Guide

Pool is less than 25,000 gallons

There is at least 10 inches of straight pipe in the return piping after all installed equipment (and

the pipe is at least 2 inches off of the ground) to install the Cell Vessel

The Control Box will be mounted within 3ft of a 120v GFCI outlet

The Control Box will be mounted within 15ft of the installed Cell Vessel

The Control Box will be installed at least 10 feet away from the pool.

Pool plumbing is 1½” or 2” PVC (If black polyethylene pipe is used, see manual)

You have a saw suitable for cutting PVC

You have tools for mounting the Control Box (drill, drill bits, screwdriver)

You have a permanent marker to mark the PVC pipe

You have balanced your pool chemistry and have 3200ppm salt in your pool (see Chemistry

Quickstart Guide)

Read this entire Quickstart Guide

Remove power to lter pump

Drain water from pool piping

Verify that all parts are included in the box

You are wearing safety glasses and have read the safety precautions in the owner’s manual

Before you begin

Overview

WWW.HAYWARD.COM 855-429-9274

Pre-Installation Checklist

Installation Preparation

Turn Over

Spread out parts on ground

1½” Nut Assembly (2)

2” Nut Assembly (2) Control Box

Screws

Strap Wrench

Compression

Ring

Collar

STEP 1: Mount Control Box

Mount the Control Box to a wall or post within 3 feet of a GFCI outlet, making sure that the cord will

reach. The Control Box will also have to be mounted within 15 feet of the Cell Vessel as shown in the

Overview.

Use the included Mounting Template to help locate the mounting holes and fasten the Control Box to the

intended surface.

Control Box

Mounting

Template

Cell Cap & Cord

Retaining Nut

Cell Vessel

Gasket (2)

Cell

Cell Vessel

Cutting Template

Grease

With the pump off and water chemistry adjusted (see Water

Chemistry Quick Start Guide), plug linecord into a 120 VAC

ground fault circuit interrupter (GFCI) safety outlet or an outlet

protected by a ground fault circuit breaker (GFCB). If local

codes require bonding, see manual.

092464 RevB

STEP 8: Calibrate Flow Switch

STEP 7: Plug in Linecord

1. After being powered on for the rst time, the

Salt & Swim will display a blinking INAD-

EQUATE WATER FLOW LED and a solid

STANDING BY LED. Keep the Salt & Swim

powered for the remainder of this procedure.

2. Turn the lter pump ON. Make sure that full

ow is achieved (no air in the system) and run

the pump for at least 15 seconds.

3. Turn the lter pump OFF for 15 seconds.

4. The Salt & Swim should now display a solid

INADEQUATE WATER FLOW and a solid

STANDING BY LED. The Flow Switch Calibra-

tion procedure is complete. You can now turn

on your lter pump and begin normal operation.

STEP 3: Install Nut Assembly

Follow the procedure below to install the Nut

Assembly.

Remove the foam protector from the Cell.

Fully cover Cell pins with supplied grease.

Verify that the O-ring is attached to the Cell

before inserting the Cell into the Cell Vessel as

shown.

STEP 5: Insert Cell

STEP 4: Install Cell Vessel

STEP 6: Attach Cap

Plug in Cell Cap and secure with

Retaining Nut.

Run the pump for 5 minutes or until all air

is out of the system. Check for leaks and

then turn the pump off.

STEP 2: Determine where Cell Vessel will be installed

The Cell Vessel must be the very last component installed in the

pool’s return piping before the water returns back to the pool. It can be

installed vertically or horizontally and requires approximately 10 inches

of straight pipe at the installation location.

Use the included Cutting Template to aid in marking and cutting

the pipe. The entire Cutting Template must t on the pipe

otherwise the Cell Vessel will not t. Secure the Template and

use a permanent marker to mark all 10 cutouts.

Salt & SwimTM Installation Quick Start Guide

IMPORTANT!

Other manuals for Salt & Swim

This manual suits for next models

Other Hayward Lighting Equipment manuals

Hayward

Hayward HL32950VVSP User manual

Hayward

Hayward ProLogic User manual

Hayward

Hayward WFBRNDBRS User manual

Hayward

Hayward POOL Rx Socket User manual

Hayward

Hayward Pro Logic User manual

Hayward

Hayward OnCommand User manual

Hayward

Hayward Aqua Rite® Pro User manual

Hayward

Hayward CL220BR series User manual

Hayward

Hayward Sheer 500 User manual

Hayward

Hayward Jiffy Niche User manual

Hayward

Hayward OmniPL HLBPRO4SW User manual

Hayward

Hayward S311SX User manual

Hayward

Hayward Salt & Swim User manual

Hayward

Hayward AquaRite+ AU Master Manual

Hayward

Hayward Sense and Dispense User manual

Hayward

Hayward 3478 PLDBL3 User manual

Hayward

Hayward TriStar VS 900 Omni User manual

Hayward

Hayward Pro Logic User manual

Hayward

Hayward VR1000 User manual

Hayward

Hayward ProLogic User manual

Hayward

Hayward KingRay User manual

Hayward

Hayward ASL C1250 User manual

Hayward

Hayward SwimPure Plus Specification sheet

Hayward

Hayward Sense and Dispense AQL-CHEM User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions