Hayward HLPMPCONV User manual
Hayward Industries
400 Connell Drive, Suite 6100
Berkeley Heights, NJ 07922
Phone: (908) 355-7995
www.hayward.com
Omni Controls
VSP Communication Board for Omni Controls
Installation Manual
HLPMPCONV
Contents
Overview................................1
Installation.............................1
Operation..............................5
092757 RevA
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Overview
The HLPMPCONV is a communication board bundled with a cable and enclosure. The HLPMPCONV
will allow full control of up to 3 Pentair variable speed pumps (VSPs) by Omni Control products. The
Omni Control can turn the pump on and off as well as vary speeds based on schedules and speed
settings.
Install and setup the pump for remote control according to its included instructions. Install and wire
the HLPMPCONV according to the instructions in this manual. After installation is complete, your
Omni Control manual will explain how to configure and control the pump.
IMPORTANT: Before attempting this installation, completely disconnect power to the pump
and to the Omni Control.
Installation
Disconnect power to both the Omni Control and the pump(s) at the circuit breakers before instal-
lation.
Mounting the Enclosure
The enclosure will hold the communication board which is wired to both the Omni Control and the
Pentair pump. Find a suitable mounting location for the enclosure that will allow wire runs to both
the pump (using the Pentair communication cable) and the control (using the included 15' cable).
Use appropriate hardware to fasten the enclosure to the mounting surface.
Wiring
The HLPMPCONV will be wired to the Omni Control and the Pentair pump using two 4 position screw
terminal connectors. These connectors can be removed from the board (pull straight up) for more
convenient access. Do not attempt to install the board into the enclosure until wiring is complete.
Omni Control - Connect the included 15' 4 conductor communication cable from the Omni Con-
trol's low speed bus connector (refer to your Omni Control Installation manual for VSP connection) to
the left connector on the HLPMPCONV as shown on the top of page 2.
Pentair Pump - The Pentair pump communication cable (supplied with the pump) will only have 2
conductors and attaches to the right connector on the HLPMPCONV. Up to two pumps can be wired
to this single connector as shown on the top of page 2. For 3 pumps, use a jumper as shown at the
bottom of page 2.
1
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
RedBlackWhite
Green
From Omni Control
Yellow
Green
From Pentair Pump(s)
VSP 2 VSP 3
12 AWG Wire to RS485 Connector
Electrical
Wire Nuts
VSP 1
Use a jumper for sys-
tems with 3 pumps
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
2
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
2
Installing HLPMPCONV into the Enclosure
After wiring is complete, insert the HLPMPCONV into the enclosure as shown.
3
USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Wires are sandwiched at exit and open
end of foam strip should be flush with
enclosure.
Routing wires through the wiring channel
Route the cables through the wiring channel and out the exit of the enclosure. Sandwich the cables
at the exit point using one of the two tear out foam strips that are attached to the cover gasket. At
the exit, lay the cables in the center of the strip and fold the strip in half. Insert the folded side down
into the lowest section of the wiring channel as shown below. The open ends of the strip should be
flush with the enclosure as shown.
Install the cover back on to the enclosure and power on the Omni Control and Pentair pump(s).
Proceed to Operation.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
4
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Operation
Update Firmware
Before attempting to operate your pump, your control's firmware must be updated. The control was
shipped with the version of firmware that was available at the time of release which may not sup-
port the HLPMPCONV. To ensure proper support, update to the latest firmware version by going to
https://www.hayward.com/firmware and downloading the latest Omni Control firmware files. Refer
to the Release Notes on that page for upgrade instructions. After the update is complete, the pump
can be configured.
Configuration and Operation
The Pentair VSP will need to be configured using your Omni Control's Configuration Wizard or Quick
Edit function. Refer to your Omni Control's Installation manual for information on how to configure
your pump. After configuration, you can set the run time, schedules and speed of the pump. This is
explained in the Omni Control's Operation manual.
5
USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
6
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
For further information or consumer
technical support, visit our website at
www.hayward.com
Hayward is a registered trademark
of Hayward Industries, Inc. © 2020 Hayward Industries, Inc.
All other trademarks not owned by Hayward are the property of their respective owners.
Hayward is not in any way affiliated with or endorsed by those third parties.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Table of contents
Other Hayward Controllers manuals
Hayward
Hayward Aqua Solar Specification sheet
Hayward
Hayward RSR3 Series Manual
Hayward
Hayward HLXPLCONTROL User manual
Hayward
Hayward Pool Rx LT User manual
Hayward
Hayward Aqua Plus® User manual
Hayward
Hayward ECP3 Series Manual
Hayward
Hayward HRSN6 series Manual
Hayward
Hayward CAT 5500 User manual
Hayward
Hayward HRSN3FS Series Manual
Hayward
Hayward HCC 1000 User manual
Hayward
Hayward CAT 2000 W3CATPP2000 User manual
Hayward
Hayward HCC 4000 User manual
Hayward
Hayward E-Command® 4 User manual
Hayward
Hayward GVA-24 User manual
Hayward
Hayward HLXPLCONTROL User manual
Hayward
Hayward CAT-2000 User manual
Hayward
Hayward CAT-1000-ORP User manual
Hayward
Hayward Aqua Solar GL-235 Specification sheet
Hayward
Hayward ECP8 Series User manual
Hayward
Hayward GLX-PCB-HPC-4 User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
