Hasbro LAZER TAG 13744 User manual

LT01_distressed

LT02_clean

AGES 8+

13744

Replace with 12 x 1.5V “AA” or R6 size alkaline batteries.

Phillips/cross head screwdriver (not included) needed to

replace batteries.

BATTERIES INCLUDED

x12

Get other manuals https://www.bkmanuals.com

STANDARD, CRT TV ONLY. NOT FOR USE WITH PROJECTION, LCD,

HIGH-DEFINITION, OR PLASMA TV.

1. Using a Phillips/cross head screwdriver (not

included), unscrew the battery covers on

your Tagger units.

2. Insert 6 fresh 1.5 V “AA” or R6 size

batteries (not included) in each Tagger

unit. Alkaline batteries recommended. See

diagram for polarity.

3. Replace battery covers and tighten screws.

Replacing the batteries:

Get other manuals https://www.bkmanuals.com

CAUTION: TO AVOID BATTERY LEAKAGE

1. Be sure to insert the batteries correctly and always follow the toy and battery

manufacturers’ instructions;

2. Do not mix old and new batteries or alkaline, standard (carbon-zinc) or

rechargeable (nickel-cadmium) batteries;

3. Always remove weak or dead batteries from the product.

IMPORTANT: BATTERY INFORMATION

Please retain this information for future reference.

Batteries should be replaced by an adult.

CAUTION:

1. Always follow the instructions carefully. Use only batteries specified and be sure

to insert item correctly by matching the + and – polarity markings.

2. Do not mix old and new batteries or standard (carbon-zinc) with alkaline

batteries.

3. Remove exhausted or dead batteries from the product.

4. Remove batteries if product is not to be played with for a long time.

5. Do not short-circuit the supply terminals.

6. Should this product cause, or be affected by, local electrical interference, move

it away from other electrical equipment. Reset (switching off and back on again

or removing and reinserting batteries) if necessary.

7. RECHARGEABLE BATTERIES: Do not mix these with any other types of

batteries. Always remove from the product before recharging. Recharge batteries

under adult supervision. DO NOT RECHARGE OTHER TYPES OF BATTERIES.

Get other manuals https://www.bkmanuals.com

THE PARTS OF YOUR TAGGER

Power/Game

Type Switch

Strength Switch

Accessory Rail

Indoor/Outdoor Switch

VIDEO GAME MODULE

PINPOINT SIGHT

Release Button

SHOT BLAST™*

Attachment

Weapon Rail

Shield Activation

Button

Trigger

Receiver Dome/Hit Indicator

Ammo Core™*

Release

Strength

Gauge

Ammo

Indicator

Ammo Core™*

Rack

Get other manuals https://www.bkmanuals.com

1. All players should agree on Strength scores for the

game, and set the Strength Switch to either 10 or

25. You can’t change your Strength score once the

game begins!

• 10 Strength means you can be tagged 10 times

before you are out of the game.

• 25 Strength means you can be tagged 25 times

before you are out of the game. Your Strength

Gauge will stay ﬁlled until you are on your last 10

Strength points.

2. Set the Indoor/Outdoor Switch to the proper

position based on where you are.

3. Decide what game type to play – Solo or Team.

• Solo Game means that all players are on their

own. The last player with any Strength Points left

wins!

• Team Game means that players organize

themselves into two teams that battle against each

other. You can’t tag someone on your own team.

There are many different team games you can play

– make up your own, or check out lazertag.com for

team game rules!

BEFORE YOU TURN ON YOUR TAGGER

Get other manuals https://www.bkmanuals.com

1. Switch your Tagger to Solo, Team 1 or Team 2.

2. When all players have set their Taggers to the right

game type, point your Tagger in the air and pull the

Trigger. This will activate a 10-second countdown,

after which the game begins!

3. To tag another Player, point your Tagger at him and

pull the Trigger. This will use one round of Ammo.

4. When all of the lights on the Ammo Indicator are out,

you need to reload. Press the Ammo Core™* Release

to pop out the Ammo Core™*. Now, push the Power

Core back in. You are reloaded and ready to continue

tagging!

5. When you are tagged, your Tagger will rumble, and

one (or more, depending on the Weapon Accessory

your opponent is using) of your Strength points will

be lost. When all of the lights on your Strength Gauge

go out, you are out of the game (your Tagger will warn

you when your Strength is down to dangerous levels).

6. The last player (or players on the same team in a

team game) with Strength points left wins!

PLAYING A GAME

Note: You have ten rounds

of Ammo after each

reload. When you ﬁre one

round, one of the lights on

your Ammo Indicator will

blink. When you ﬁre the

second, the blinking light

will go out.

.com

The PHOENIX LTX™* Tagger is compatible with all LAZER TAG

Team Ops gear from TIGER ELECTRONICS™* and HASBRO®*.

See for more details.

Get other manuals https://www.bkmanuals.com

When your shield is active, you

cannot be tagged, but you also can’t

tag anyone.

1. To activate your Shields, press and

hold the Shield Activation Button.

2. The shield will stay on for up to

10 seconds. You will hear it power

up and hum. While your shield is

up, you cannot tag or be tagged.

3. After you release the Shield

Activation Button, you will hear

your shield power down. You are

now vulnerable to tags, and can

tag other players.

4. You must wait 2 seconds before

activating your shields again.

5. You only have a few seconds of

shield charge per game, so use

them wisely!

USING THE SHIELDS

You get 15

seconds of

Shields during

a 10 Strength

game.

You get 30

seconds of

Shields during

a 25 Strength

game.

Get other manuals https://www.bkmanuals.com

1. Slide the PINPOINT SIGHT onto the accessory rail

on the top of your Tagger until it locks into place.

2. Look into the PINPOINT SIGHT. If it is properly

attached, you will see a green dot reﬂected on the

crosshairs.

3. Line up the green dot in the center of the

crosshairs with your target for pinpoint accuracy!

USING THE SHOT BLAST™* WEAPON ACCESSORY

Note: Tags ﬁred by the

SHOT BLAST accessory

have a shorter range than

regular tags, but affect a

wider area. If you catch

several opponents standing

close to one another, you

can actually hit all of them

at once!

USING THE PINPOINT SIGHT

1. Slide the SHOT BLAST accessory onto the

front of the Tagger until it snaps into place.

2. To arm the SHOT BLAST, slide the Rack

toward you, and then forward again.

3. When you pull the trigger, your Tagger will ﬁre

an extra-powerful blast. Depending on how

accurate your shot is, you could take as many

as three points off your target’s Strength

Gauge.

4. You will need to Rack the SHOT BLAST again

before you can ﬁre it.

5. If you pull the Trigger without using the Rack,

you will ﬁre a single, regular Tagger shot.

6. To remove the SHOT BLAST, slide the

Release Button down and pull it off

the Tagger.

Get other manuals https://www.bkmanuals.com

Slide the Video Game Module onto the

accessory rail on the front of your Tagger,

until it locks into place.

To remove it, slide the Release Button

down and pull the Module off the Tagger.

USING THE VIDEO GAME MODULE

Plug it in, and experience intense, single-player Lazer Tag action on your television!

REQUIREMENTS

TV with AV input OR VCR or DVD player with AV input attached to your TV.

• RF Adapter (not included) required if your TV does not have an AV input.

• STANDARD, CRT TV ONLY. NOT FOR USE WITH PROJECTION, LCD, HIGH-DEFINITION, OR PLASMA TV.

• You cannot play this game through a cable box or satellite hookup. Game must be

connected directly to the TV, VCR, or DVD player.

• If the game malfunctions or freezes, you can reset it by turning your Tagger off

and then on again.

Note: Do not use the PINPOINT SIGHT with

the Video Game Module.

ASSEMBLY

Get other manuals https://www.bkmanuals.com

Connecting to a TV:

1. Insert the cable’s white plug into the white audio-in jack

on the TV.

2. Insert the cable’s yellow plug into the yellow video-in jack

on the TV.

Connecting to a VCR or DVD player:

1. Make sure the VCR or DVD player is properly connected

to the TV.

2. Insert the cable’s white plug into the white audio-in

jack on the VCR or DVD player.

3. Insert the cable’s yellow plug into the yellow video-in

jack on the VCR or DVD player.

4. Turn on your TV and VCR or DVD player.

5. Set your TV, VCR or DVD player to the channel/video input

mode directed by your TV, VCR or DVD player owner’s manual.

SETUP

Insert the cable plugs into the AV inputs on your TV, VCR or DVD player.

POWER

STEREO

TIMER/

STAND BY

- CHANNEL +

- VOLUME +

TV/VIDEO

DEMO

VIDEO

VIDEO 2 INPUT

L AUDIO R

Note: these jacks are normally found on the front of

the TV near the adjustment controls, or on the back

of the TV near the antenna and cable connections

3. Turn on your TV, and set it to the channel/video input mode

directed by your TV owner’s manual.

Get other manuals https://www.bkmanuals.com

Table of contents

Other Hasbro Toy manuals

Hasbro

Hasbro MB Games Bulls-Eye Baseball User manual

Hasbro

Hasbro Power Rangers Mighty Morphin Triceratops Dinozord and Sabertooth Tiger... User manual

Hasbro

Hasbro NERF N-STRIKE ELITE MEGA MAGNUS A4796 User manual

Hasbro

Hasbro Rodimus 80231 User manual

Hasbro

Hasbro furReal Rollies User manual

Hasbro

Hasbro Play-Doh DreamWorks Trolls World Tour User manual

Hasbro

Hasbro 6776050000 User manual

Hasbro

Hasbro furReal Walkalots User manual

Hasbro

Hasbro FurReal Friends Teacup Pup 77480 User manual

Hasbro

Hasbro Baby Uh-Oh User manual

Hasbro

Hasbro 75024 User manual

Hasbro

Hasbro Moonlight Celebration with Moondancer... User manual

Hasbro

Hasbro The Clone Wars 6779630000 User manual

Hasbro

Hasbro 69550/69398 User manual

Hasbro

Hasbro GIJoe Hurricane User manual

Hasbro

Hasbro Martian Matter Alien Lab User manual

Hasbro

Hasbro FurReal E7963 User manual

Hasbro

Hasbro The Clone Wars AEGS 5+ User manual

Hasbro

Hasbro Transformers Armada 7052 User manual

Hasbro

Hasbro FurReal Friends Pom Pom My Baby Panda User manual

Hasbro

Hasbro Playskool Sesame Street Lullaby & Goodnight... User manual

Hasbro

Hasbro Star Wars Revenge of the Sith Energy Blaster refill... User manual

Hasbro

Hasbro Retaliator User manual

Hasbro

Hasbro furReal PeeALOTS User manual

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Build instructions

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

iKarus

iKarus ECO 8 Assembly instruction

Multiplex

Multiplex EasyStar II Building instructions

Walkera

Walkera 38 User handbook

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

Meccano

Meccano 15103 instructions

LEGO

LEGO TECHNIC 8735 instructions

Mattel

Mattel HOTWHEELS DWL04 instructions