Hand Held Products 4800p User manual
™
4800p
4800p 2D Imager
User’s Guide
Disclaimer
Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make
changes in specifications and other information contained in this document
without prior notice, and the reader should in all cases consult Hand Held
Products to determine whether any such changes have been made. The
information in this publication does not represent a commitment on the part of
Hand Held Products.
Hand Held Products shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages
resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of Hand
Held Products.
©2007 Hand Held Products, Inc. All rights reserved.
Web Address: www.handheld.com
Microsoft®Windows®is either a registered trademark or trademarks of Microsoft
Corporation in the United States and/or other countries.
Macintosh®is a trademark of Apple Computer, Inc., registered in the U.S. and
other countries.
Other product names or marks mentioned in this document may be trademarks
or registered trademarks of other companies and are the property of their
respective owners.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Class B Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio or television technician for help.
Caution: Any changes or modifications made to this equipment not
expressly approved by Hand Held Products, Inc. may void the
FCC authorization to operate this equipment.
Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be Hand Held Products approved shielded
cables, in which the cable shield wire(s) have been grounded (tied) to the
connector shell. Installation of the included ferrite is required to meet
emission requirements.
Canadian Notice
This equipment does not exceed the Class B limits for radio noise emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant
les limites applicables aux appareils numeriques de la classe B prescrites dans
le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be shielded cables, in which the cable
shield wire(s) have been grounded (tied) to the connector shell.
Installation of the included ferrite is required to meet emission
requirements.
CE Mark
The CE mark on the product indicates that the system has been
tested to and conforms with the provisions noted within the 2004/108/
EC Electromagnetic Compatibility Directive and the 2006/95/EC Low
Voltage Directive.
Complies with:
EN55022:2006 (for ITE emissions)
EN55024:1998 (for ITE immunity)
EN61000-3-2:2000
EN61000-3-3:1995
For further information please contact:
Hand Held Products
Nijverheidsweg 9-13
5627 BT Eindhoven
The Netherlands
Hand Held Products, Inc. shall not be liable for use of our product with equipment
(i.e., power supplies, personal computers, etc.) that is not CE marked and does
not comply with the Low Voltage Directive.
Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be shielded cables, in which the cable
shield wire(s) have been grounded (tied) to the connector shell.
Installation of the included ferrite is required to meet emission
requirements.
UL and cUL Statement
UL and cUL listed: UL60950-1 and CSA C22.2 No.60950-1.
LED Safety Statement
This device has been tested in accordance with EN60825-1:1993+A1+A2 LED
safety, and has been certified as a Class 1 LED device.
GS Mark
This product has been issued a GS certificate.
Patents
Please refer to the product packaging for a list of patents.
Waste Electrical and Electronic Equipment Information
For European Community Users
Note: Hand Held Products complies with Directive 2002/96/EC OF THE
EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003
on waste electrical and electronic equipment (WEEE).
This product has required the extraction and use of natural resources for its
production. It may contain hazardous substances that could impact health and
the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment and
to diminish the pressure on the natural resources, we encourage you to use the
appropriate take-back systems for product disposal. Those systems will reuse or
recycle most of the materials of the product you are disposing in a sound way.
The crossed out wheeled bin symbol informs you that the product should
not be disposed of along with municipal waste and invites you to use the
appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling systems,
please contact your local or regional waste administration.
You may also contact your supplier for more information on the environmental
performances of this product.
i
Chapter 1 - Getting Started
About This Manual ............................................................... 1-1
Unpacking the Imager........................................................... 1-1
Imager Models ...................................................................... 1-2
Imager Identification ............................................................ 1-2
Connecting the Imager with USB ........................................ 1-3
Programming the Interface - Plug and Play.......................... 1-4
USB PC or Macintosh®Keyboard ................................. 1-4
USB HID........................................................................ 1-4
USB COM Port Emulation............................................. 1-5
Reading Techniques.............................................................. 1-5
4800p Stand .......................................................................... 1-6
Chapter 2 - Terminal Interfaces
Terminal ID .......................................................................... 2-1
Supported Terminals............................................................. 2-2
Keyboard Country ................................................................ 2-3
Keyboard Style ..................................................................... 2-5
Keyboard Modifiers ............................................................. 2-7
Chapter 3 - Output
Good Read Indicators ........................................................... 3-1
Beeper – Good Read ...................................................... 3-1
Beeper Volume – Good Read ........................................ 3-1
Beeper Pitch – Good Read ............................................. 3-2
Beeper Duration – Good Read ....................................... 3-2
Number of Beeps – Good Read ..................................... 3-2
Good Read Delay.................................................................. 3-3
User-Specified Good Read Delay......................................... 3-3
Reread Delay ........................................................................ 3-4
User-Specified Reread Delay ............................................... 3-4
LED Power Level ................................................................. 3-5
Centering............................................................................... 3-5
Table of Contents
ii
Decode Search Mode............................................................ 3-7
Output Sequence Overview .................................................. 3-7
Output Sequence Editor ............................................... 3-10
Require Output Sequence............................................. 3-10
Print Weight........................................................................ 3-11
Video Reverse..................................................................... 3-11
Working Orientation........................................................... 3-12
Chapter 4 - Data Editing
Prefix/Suffix Overview......................................................... 4-1
To Add a Prefix or Suffix: ............................................. 4-2
To Clear One or All Prefixes or Suffixes:...................... 4-3
To Add a Carriage Return Suffix to all Symbologies .... 4-3
Prefix Selections............................................................. 4-4
Suffix Selections ............................................................ 4-4
Function Code Transmit................................................. 4-4
Intercharacter, Interfunction, and Intermessage Delays ....... 4-5
Intercharacter Delay ....................................................... 4-5
User Specified Intercharacter Delay .............................. 4-6
Interfunction Delay ........................................................ 4-6
Intermessage Delay ........................................................ 4-7
Chapter 5 - Data Formatting
Data Format Editor Introduction .......................................... 5-1
To Add a Data Format.................................................... 5-1
Other Programming Selections ...................................... 5-2
Data Format Editor Commands ..................................... 5-2
Data Format Editor......................................................... 5-5
Data Formatter ............................................................... 5-5
Alternate Data Formats .................................................. 5-6
iii
Chapter 6 - Symbologies
Message Length Description................................................. 6-2
Codabar Start/Stop Characters....................................... 6-3
Codabar Check Character............................................... 6-3
Codabar Concatenation .................................................. 6-4
Codabar Message Length ............................................... 6-5
Code 39 Start/Stop Characters....................................... 6-6
Code 39 Check Character............................................... 6-6
Code 39 Message Length ............................................... 6-7
Code 39 Append............................................................. 6-8
Code 32 Pharmaceutical (PARAF) ................................ 6-8
Full ASCII ...................................................................... 6-9
Code 39 Code Page ...................................................... 6-10
Check Digit................................................................... 6-10
Interleaved 2 of 5 Message Length .............................. 6-11
Code 93 Message Length ............................................. 6-12
Code 93 Code Page ...................................................... 6-12
Straight 2 of 5 Industrial Message Length ................... 6-13
Straight 2 of 5 IATA Message Length ......................... 6-14
Matrix 2 of 5 Message Length ..................................... 6-15
Check Digits Required ................................................. 6-16
Code 11 Message Length ............................................. 6-16
ISBT 128 Concatenation .............................................. 6-17
Code 128 Message Length ........................................... 6-18
Code 128 Code Page .................................................... 6-18
Telepen Output ............................................................. 6-19
Telepen Message Length.............................................. 6-19
UPC-A Check Digit...................................................... 6-20
UPC-A Number System ............................................... 6-20
UPC-A Addenda........................................................... 6-21
UPC-A Addenda Required........................................... 6-21
UPC-A Addenda Separator .......................................... 6-21
UPC-E0 ........................................................................ 6-22
UPC-E0 Expand ........................................................... 6-22
UPC-E0 Addenda Required ......................................... 6-23
UPC-E0 Addenda Separator......................................... 6-23
iv
UPC-E0 Check Digit.................................................... 6-23
UPC-E0 Number System ............................................. 6-24
UPC-E0 Addenda......................................................... 6-24
EAN/JAN-13 Check Digit ........................................... 6-25
EAN/JAN-13 Addenda ................................................ 6-26
EAN/JAN-13 Addenda Required................................. 6-26
EAN/JAN-13 Addenda Separator ................................ 6-26
ISBN Translate............................................................. 6-27
EAN/JAN-8 Check Digit ............................................. 6-27
EAN/JAN-8 Addenda .................................................. 6-28
EAN/JAN-8 Addenda Required................................... 6-28
EAN/JAN-8 Addenda Separator.................................. 6-28
MSI Check Character................................................... 6-29
MSI Message Length ................................................... 6-30
Plessey Message Length .............................................. 6-30
RSS Expanded Message Length .................................. 6-32
PosiCode Message Length ........................................... 6-33
Codablock F Message Length...................................... 6-34
Code 16K Message Length .......................................... 6-35
Code 49 Message Length ............................................. 6-36
PDF417 Message Length ............................................. 6-37
MicroPDF417 Message Length ................................... 6-38
UPC/EAN Version ....................................................... 6-39
EAN•UCC Composite Code Message Length............. 6-39
4-CB (4-State Customer Bar Code) ............................. 6-41
ID-tag (UPU 4-State) ................................................... 6-41
Postnet.......................................................................... 6-41
Planet Code .................................................................. 6-42
British Post................................................................... 6-43
Canadian Post............................................................... 6-43
Kix (Netherlands) Post................................................. 6-43
Australian Post ............................................................. 6-44
Australian Post Interpretation ...................................... 6-44
Japanese Post................................................................ 6-44
China Post Message Length ......................................... 6-45
Korea Post Message Length......................................... 6-46
QR Code Message Length ........................................... 6-47
Other manuals for 4800p
2
Table of contents
Other Hand Held Products Barcode Reader manuals
Hand Held Products
Hand Held Products Quick Check PC600 User manual
Hand Held Products
Hand Held Products HandHeld 3800 Linear Series User manual
Hand Held Products
Hand Held Products IT4000 Use and care manual
Hand Held Products
Hand Held Products IMAGETEAM 4620 User manual
Hand Held Products
Hand Held Products IMAGETEAM 3800E User manual
Hand Held Products
Hand Held Products IMAGETEAM 3900 User manual
Hand Held Products
Hand Held Products QUICK CHECK 890 User manual
Hand Held Products
Hand Held Products 3200 User manual
Hand Held Products
Hand Held Products HandHeld 3800 Linear Series User manual
Hand Held Products
Hand Held Products Scanteam 5700 User manual
Hand Held Products
Hand Held Products DOLPHIN RF User manual
Hand Held Products
Hand Held Products IMAGETEAM 4410 User manual
Hand Held Products
Hand Held Products IMAGETEAM 3800i User manual
Hand Held Products
Hand Held Products 3800LR User manual
Hand Held Products
Hand Held Products 4820 User manual
Hand Held Products
Hand Held Products Quick Check Bar Code Verifiers 800 User manual
Hand Held Products
Hand Held Products 4800p User manual
Hand Held Products
Hand Held Products 4600g User manual
Hand Held Products
Hand Held Products 4230 User manual
Hand Held Products
Hand Held Products SV Series User manual
