HAMPTON BAY 597-730 User manual

USE AND CARE GUIDE

SENZE 52 INCH CEILING FAN

THANK YOU

HAMPTONBAY.COM

Item #597-730

Model #24816-021

Questions, problems, missing parts? Before returning to the store,

call Hampton Bay Customer Service

8 a.m. - 6 p.m., EST, Monday-Friday

1-877-527-0313

ASSEMBLY

1Preparing the canopy 2Preparing the motor

□Remove the canopy bottom cover (C) from the canopy

(B) by turning the canopy bottom cover (C) counter-

clockwise.

□Remove the mounting bracket (A) from the canopy (B)

by removing the non-slotted mounting bracket screw

(BB) from the bottom of the canopy (B) and loosening

the slotted mounting bracket screw (BB) a half turn

from the screw head. Next, turn the canopy (B)

counterclockwise to remove the mounting bracket (A)

from the canopy (B).

□Remove the clevis pin (GG) and cotter pin (HH), and

loosen the two collar setscrews (II) from the fan

motor assembly (F) collar.

3Assembling the fan

□Route the wires exiting from the top of the fan motor

assembly (F) through the coupling cover (E) and the

canopy bottom cover (C). Ensure the slot openings

are on top.

□Route the wires through the canopy (B) and then

through the hanger ball/downrod assembly (D).

□Align the holes at the bottom of the hanger

ball/downrod assembly (D) with the holes in the collar

on top of the fan motor assembly (F).

□Carefully insert the clevis pin (GG) through the holes

in the collar and the hanger ball/downrod assembly

(D). Be careful not to jam the clevis pin (GG) against

the wiring inside the hanger ball/downrod assembly

(D).

WARNING: Failure to properly install the cotter pin (HH)

could result in the fan loosening and possibly falling.

NOTE: If a longer downrod (not included) is needed, take

out the screw located in the hanger ball, lower the hanger

ball, and remove the pin. Remove all three pieces from the

downrod and assemble them onto the new, longer downrod

before proceeding to the downrod installation.

Assembly - Assembling the Fan Body

□Insert the cotter pin (HH) through the hole near the

end of the clevis pin (GG) until it snaps into the locked

position.

□Firmly tighten the two collar setscrews (II) on top of

the fan motor assembly (F).

II II

Assembly — Hanging the Fan

4Attaching the mounting bracket

to the electrical box

Hanging the fan from the

mounting bracket

□Pass the 120 volt supply wires through the center

hole in the mounting bracket (A).

□Attach the mounting bracket (A) to the outlet box (NN)

with the screws and washers provided with your

outlet box (NN).

□Securely tighten the two mounting screws.

WARNING: To reduce the risk of ﬁre, electric shock, or

other personal injury, mount the fan only to an outlet box or

supporting system marked acceptable for fan support and

use the mounting screws provided with the outlet box.

WARNING: The tab in the ring must rest in the groove of

the hanger ball/downrod assembly (D). Failure to properly

seat the tab in the groove could cause damage to the wiring.

□Carefully lift the fan motor assembly (F) up to the

mounting bracket (A), and seat the hanger

ball/downrod assembly (D) in the mounting bracket

(A) socket. Make sure the tab on the mounting

bracket (A) socket is properly seated in the groove in

the hanger ball/downrod assembly (D). This will help

to balance the ceiling fan.

9HAMPTONBAY.COM

Please contact 1-877-527-0313 for further assistance.

6Preparing the receiver and

remote control

Assembly — Preparing the Remote Control

If you feel you do not have enough electrical wiring

knowledge or experience, have your fan installed by a

licensed electrician.

This remote control unit is equipped with 16 code

combinations to prevent possible interference from or to

other remote units. The frequency switches on your

receiver (L) and remote control (M) have been preset at

the factory. Please recheck to make sure the switches on

the remote control (M) and the receiver (L) are set to the

same position. Any combination of settings will operate

the fan as long as the switches in the remote control (M)

and receiver (L) are set to the same position.

□After checking the switches, insert the receiver (L)

into the mounting bracket (A) with the ﬂat side of the

receiver (L) facing the ceiling.

CAUTION: The frequency switches on the receiving unit are

covered with a rubber cover. Remove the rubber cover, and

then replace it after making any changes to the frequency

switches.

CAUTION: Do not use with a wall light dimmer switch.

WARNING: To avoid possible electrical shock, ensure

electricity is turned off at the main fuse box before

connecting the wiring.

7Making the electrical connections

Assembly — Making Electrical Connections

Follow the steps below to connect the fan to your

household wiring. Use the plastic wire nuts (AA) with your

fan. Secure the wire nuts (AA) with electrical tape. Make

sure there are no loose strands or connections.

Motor to receiver electrical connections:

□Connect the black wire (PP) from the fan to the black

wire (AAA) marked "TO MOTOR L" from the receiver

(L).

□Connect the white wire (RR) from the fan to the white

wire (BBB) marked "TO MOTOR N" from the receiver

(L).

□Connect the blue wire (QQ) from the fan to the blue

wire (CCC) marked "For Light" from the receiver (L).

Receiver to house supply wires electrical connections:

□Connect the black (hot) wire (FFF) from the ceiling to

the black wire (DDD) marked "AC in L" from the

receiver (L).

□Connect the white (neutral) wire (GGG) from the

ceiling to the white wire (EEE) marked "AC in N" from

the receiver (L).

□If your outlet box (NN) has a ground wire (HHH) (green

or bare copper) connect it to the fan ground wire (III);

otherwise connect the hanger ball/downrod assembly

(D) ground wire to the mounting bracket (A).

□Secure each wire connection with a plastic wire nut

(AA) provided with the electrical hardware.

□After connecting the wires, spread them apart so that

the green and white wires are on one side of the

outlet box (NN) and the black and blue wires are on

the other side. Carefully tuck the wire connections up

into the outlet box (NN).

WARNING: Check to see that all connections are tight,

including the ground, and that no bare wire is visible at the

wire nuts, except for the ground wire.

NOTE: The fan must be installed at a maximum distance of

20 feet from the remote control for proper signal transmission

between the remote control and the fan's receiving unit.

CAUTION: Do not use with a wall light dimmer switch.

11 HAMPTONBAY.COM

Please contact 1-877-527-0313 for further assistance.

DDD

FFF GGG

HHH

EEE

AAA

CCC

BBB

III

Assembly — Completing the Fan Body

8Installing the canopy

□Make sure connections are neatly tucked in the

ceiling outlet box (NN).

□Slide the canopy (B) up to the mounting bracket (A)

and place the key hole on the canopy (B) over the

loose mounting bracket screw (BB) on the mounting

bracket (A). Turn the canopy (B) clockwise until it

locks in place at the narrow section of the key holes.

□Align the circular hole on the canopy (B) with the

remaining hole on the mounting bracket (A). Secure

the mounting bracket screw (BB) previously removed

in the hole, and tighten the two mounting bracket

screws (BB).

WARNING: Make sure the tab on the mounting bracket (A)

properly sits in the groove in the hanger ball/downrod

assembly (D) before attaching the canopy (B) to the mounting

bracket (A) by turning the canopy housing until it drops into

place.

NOTE: Adjust the mounting bracket screws (BB) as

necessary until the canopy (B) and canopy bottom cover (C)

are snug.

Attaching the canopy

bottom cover

□Attach the canopy bottom cover (C) to the mounting

bracket screw (BB) heads on the bottom of the

canopy (B) by inserting the screw heads into the key

slots in the canopy bottom cover (C) and rotating the

canopy bottom cover (C) clockwise.

Assembly — Attaching the Fan Blades

□Insert the blade (G) through the slot in the housing. Align

the holes in the blade (G) and the fan motor assembly (F)

and secure with a blade attachment screw and ﬁber

washer (CC).

□Repeat this procedure with the remaining blades (G).

WARNING: To reduce the risk of personal injury, do not

bend the blades (G) while installing, balancing the blades (G),

or cleaning the fan.

WARNING: Do not insert foreign objects between rotating

fan blades (G).

Attaching the Fan Blades

13 HAMPTONBAY.COM

Please contact 1-877-527-0313 for further assistance.

11 Attaching the light kit mounting

plate to the mounting ring 12

□Remove one of the three mounting plate screws (JJ)

from the mounting ring (SS), and loosen the other

two screws. (Do not remove.)

□Place the key holes in the light kit mounting plate (H)

over the two screws (JJ) previously loosened from

the mounting ring (SS). Turn the light kit mounting

plate (H) until it locks in place at the narrow section

of the key holes. Secure by tightening the two

mounting plate screws (JJ) previously loosened and

the one (JJ) previously removed.

Attaching the light kit to

the mounting plate

□Remove one of the three light kit mounting screws

(KK) from the mounting plate (H), and loosen the

other two screws (KK). (Do not remove.)

□While holding the light kit (I) under your fan (F), snap

together the wire connection plugs (TT).

□Place the key holes in the light kit (I) over the two

mounting screws (KK) previously loosened from the

mounting plate (H). Turn the light kit (I) until it locks

in place at the narrow section of the key holes.

Secure by tightening the two light kit mounting

screws (KK) previously loosened and the one (KK)

previously removed.

Assembly — Installing the Light Kit

13 Installing the glass shade

Assembly — Installing the Light Kit (continued)

□Remove the decorative nut (MM) from the light kit (I).

□Install the three 40-watt candelabra bulbs (P)

(included).

□Place the glass shade (J) over the light kit (I) stem.

Secure the glass shade (J) with the metal nut (LL)

(rubber side on the top). Do not overtighten.

□Place the glass frame (K) onto the light kit (I) stem.

Secure the glass frame (K) with the decorative nut

(MM).

HAMPTONBAY.COM

Please contact 1-877-527-0313 for further assistance.

Operation

REMOTE CONTROL OPERATING INSTRUCTIONS

INSTALLING THE REMOTE CONTROL HOLDER

□Remove the two remote control holder plugs (FF) from the

remote control holder (O). Note that the plugs have unique

tabs that allow them to ﬁt only in one hole.

□Attach the remote control holder (O) with the two remote

control holder mounting screws (EE).

□Replace the two remote control holder plugs (FF) each into its

own hole.

□Restore power to the ceiling fan, and test for proper operation.

HI, MED, LOW buttons: set the fan speed.

OFF button: turns the fan off.

button: turns the light ON or OFF and also controls the

brightness setting. Press and release the button to turn the light

ON or OFF. Press and hold the button to set the desired brightness.

The light button has an auto-resume; it will stay at the same

brightness as the last time it was turned off.

□Install a 12V MN21/A23 battery (N) (included) into the remote

control (M). To prevent damage to the remote control (M),

remove the battery if not used for long periods.

This manual suits for next models

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY Vasner 529-751 User manual

HAMPTON BAY

HAMPTON BAY BELVOY AK330-BN User manual

HAMPTON BAY

HAMPTON BAY 699 810 User manual

HAMPTON BAY

HAMPTON BAY SW19129-A ORB User manual

HAMPTON BAY

HAMPTON BAY Trusseau User manual

HAMPTON BAY

HAMPTON BAY AG524-BN User manual

HAMPTON BAY

HAMPTON BAY 52" ELKTON User manual

HAMPTON BAY

HAMPTON BAY Wellston User manual

HAMPTON BAY

HAMPTON BAY Windward II User manual

HAMPTON BAY

HAMPTON BAY PALM BEACH III 48-PBH User manual

HAMPTON BAY

HAMPTON BAY Gazebo II User manual

HAMPTON BAY

HAMPTON BAY FC120-CARL User manual

HAMPTON BAY

HAMPTON BAY 134674 User manual

HAMPTON BAY

HAMPTON BAY BAYFIELD User manual

HAMPTON BAY

HAMPTON BAY TUDOR User manual

HAMPTON BAY

HAMPTON BAY 52202 User manual

HAMPTON BAY

HAMPTON BAY HALWIN AK396H-BN User manual

HAMPTON BAY

HAMPTON BAY WELLSTON EF200B-44 User manual

HAMPTON BAY

HAMPTON BAY 286-780 User manual

HAMPTON BAY

HAMPTON BAY Trieste User manual

HAMPTON BAY

HAMPTON BAY 1005 819 968 User manual

HAMPTON BAY

HAMPTON BAY SOUTHWIND User manual

HAMPTON BAY

HAMPTON BAY SUSSEX User manual

HAMPTON BAY

HAMPTON BAY GAZEBO YG188-BN User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual