Haier XQB50-20 User manual

XQB50-20

Part specialized code 0030504485

The product is used only in the Chinese continent..If

other countries or areas need it, please contact us.

Before using

User's manual

Fuzzy Logic Automatic

Washing Machine

Contents

Names of the parts.........the 2nd cover

Safety precautions ............................1

Special function introduction ............ 3

Installation and adjustment ...............3

Install the water inlet hose.................5

Preparation before washing .............7

Put in the laundries ...........................8

Add the detergent/softener ...............9

Use the operation buttons ...............10

Close the top lid ..............................14

Washing finished .............................14

Disposal after washing ....................15

Using process

Trouble shooting Answer to

question.........................................16

Specification..............the back cover

Packing list .....................................17

Please check if the power receptacle has good

earthing condition before using to guarantee

your safety.

Please read this manual carefully before using.

The manufacturer will not take responsibility for

those risks occurred from not obeying this manual.

Retain it for future reference.

Adjustable foot

Adjustable foot labal

Cabinet

Base

Control panal

Control panel film

Pulsator

Top lid component

Power line

Location for lint filter

Fixed foot(3)

Back cover

Drain hose

Cabinet handle

Hanging hole

for the drain

hose

Water absorption

cushion

Water valve

Blance ring

Inner tub

Names of the parts

Honorable users,

Thanks for your choosing Haier products.

To facilitate your operation, please read the manual carefully and operate this

machine according to it.

Detergent box

Filter cover

Location for liquid bleacher

Accessories

Meaning and description of the symbols

Warning sign

Forbidding sign

Contents marked with that symbol

are related to the safety of the

product and the personal safety

of the users. Please operate in

strict conformity to the contents.

Otherwise, it may cause damage

of the machine or injure the

personal safety of the user.

Contents marked with that symbol

are actions forbidden to perform.

Performing of those actions may

result in damage of the machine

or injure the personal safety of

the user.

Lint filter

(one)

Bottom plate

(one)

Water inlet hose

(one)

Water inlet

Hose jointer

(one)

Tapping screws

(five)

The end connecting to

the water inlet hose jointer

The end connecting to

the washing machine

Jointer connecting the

water inlet hose and

the water faucet

All the pictures in this manual are sketch-map. And because of the improvement

of product, so the washing machine and accessories which

continual

you received cannot be match

accurately with the sketch map in this manual.

Before Using

Safety precautions

The ventilation

holes at the bottom

In case the washing machine is installed on ground

with carpet, be careful not to block the ventilation hole

with carpet.

Do not put the machine at damp place like the

bathroom. Never wash it with water. Do not

put wet laundries on the control panel coating.

Do not let the machine share one receptacle with other

electric appliances. If the plugging into the receptacle

is loose, do not use the plug any more.

Do not wash waterproof laundry like the raincoat,

bikecovers, down textiles etc. To avoid abnormal

vibrations in spinning.

In normal usage of the washing machine, the power

plug shall be ready to be pulled or plugged with hang.

Be sure to pull the plug off and close the water faucet

when occurring power failure, delivering the machine,

setting the machine idle or cleaning the machine, Do

not plug or pull the power plug with wet hand.

Do not use water with temperature higher than 50

Please plug the plug on special 220V~240 AC

receptacle.Be sure to use three phase power

receptacle. Ensurethe earthing prong of the power

receptacle is earth-ed reliably. Use a leakage

protector if possible.

50 C

Earth

Do not bend, stretch, twist, bind the power cord by force, or reform it.

Do not press or clamp it with heavy items. If the power cord and power

plug are bad, or the receptacle is loose, be sure to have it replaced by

the technicians of our special shop or our agent,or the after-sales service

department to avoid any risk.Keep the prong of the power plug clean.If

dust is found on the power plug, please wipe it off with dry cloth.

Before Using

Safety precautions

Do not decompose, repair or alter the machine

by yourself.

Do not put any hot or heavy items (such as the kettle

with hot water ) on the washing machine.

Do not wash laundries with volatile materials

(such as thinner, petrol etc.)

The handicapped or children without care shall not

use the machine.

Keep the machine away from direct sunlight and

heat source like the heater.

To prevent the lint inside the tub from blocking the

cascade outlet during washing, please keep the

lint filter in good condition, and install it to proper

position. If the lint filter is lost or damaged, please

contact the local after-sales service department of

our company.

Petrol

Thinner

Do not put hand into the rotating tub. It is dangerous

even if the rotation speed is slow. Take special care of

the children. Keep children away from the washing

machine to avoid them climbing on.

To protect your laundries and washing machine,

please take out all of the coins, buttons, sand, hairpin

and other foreign materials before washing.

Please check if the water faucet is open, and if the

connection of the water inlet pipe is proper. if the

drain pipe is put down.

It is suggested to use foamless washing powder.

Dismantle

Install

After switching on the Power, select the memory programme(the tube on).Then select appropriate time of SOAK, WASH and SPIN

and the time of rinse on need. After setting, the washing machine memorized the programme set by yourself. When switching on

the Power again, press the PROGRAM button, and select the MEMORY program, the program set by yourself will start

automatically. Using the MEMORY program, you can storage the program which meets with your individual need.

Eliminating foam rinse

Memory programme

Press the RINSE button, when the tube is on, it indicates that you have chosen the ELIMINATING FOAM RINSE PROGRAM, and

perform eliminating foam rinse firstly. Then, it will fill water continuously after the water level is high, and the foam in the tub will

overflow from the overflow inlet, and avoiding polluting the clothes again.

After you open the package, please lean the washing

machine gently down on soft items ( like the towel cloth,

blanket, etc. ). Install the bottom plate to the bottom of

the machine with the five screws by a cross screwdriver,

then lift the machine up gently. See to the figure:

Back

Front

Soft items

Ajustable foot

Screw

Bottom plate

Before Using

Special function introduction

Please install and adjust the machine according to the requirement of the manual. It is

very important to your security and correct operating the machine.

Installation and adjustment

Install bottom plateInstall lint filter

Install

Push lint filter downward to location for

lint filter

The distance that washing machine away from wall should be above 20mm. The largest allowed slope of the

shank base of the machine is 2 . The slanting or rough ground will result in unstable running or stoppage

of the machine. Please adjust it with following methods:

Adjust the adjustable foot:

Adjust the installation position

1.To twist the adjustable foot, please first lift up

the side of the foot slightly, loosen the adjustable

nut, and twist the foot.

2.Fasten the nut after adjustment.

Loosen

High

Fasten

Adjustable feet

Low

Adjustable nut

Confirm it's horizontal:

Hang the lead line to confirm if it is horizontal.

1 Loosen the fastening screws of the back cover,unpack

the back cover gently, avoiding to break the clip claw.

Figure 1

3 Stretch out the drain hose to the right of the frame

from the groove. Fasten it in the base frame with the

drain hose support, and fasten the screws.Then hang

the hook in the drain hose, and hang the drain hose in

the hole of the cabinet. (Figure 3)

2 Take the drain hose from the cabinet, make the mouth of

it flat a little, dismantle the pothook, loosen the fastening

screws, dismantle the drain hose support ,and pull the drain

hose into the cabinet from the left of the base.

Figure 2

Screws

Back cover

( Figure 3 )

(Figure 4)

Lower hook

Upper tab

Side tab

Make the mouth of the

drain hose flat, take off

the pothook.

Drain hose frame

Screws

1.Never let the drain hose exceed 10cm above the

ground. If the timeof draining is too long, the washing

machine will stop in the midway.

3.If the drain hose is too long, cut it at mid point. To make

smooth drainage, cut the front end of the hose slantingly.

4.If extra drain hose is needed, please make separate

purchase. The inner diameter of the extra hose shall

not less than 30mm, and the length shall not exceed

1.5m.

5. If the extra hose is too long,cut it either at A or

at B

<10cm

> 30mm

<1.5m

How to change the direction of the drain hose

Usage of the drain hose

The drainage shall be smooth with the drain hose.

2.Do not step on or press the drain hose.

Before Using

( Figure 2 )

4 Install the back cover. Hang the under side of the

back cover on the cabinet firstly, then push the left

, the right tab and the upside into the cabinet.

Do not do it strongly, and fasten the screws.

(Figure 4)

Water faucet, suitable Water faucet, not suitable

It is required that the front end shall be longer than 10cm.

The outlet end surfaceof the faucet shall be flat and smooth. If not please file it

to avoid leakage.

2.Loosen the screw till the water faucet can be accessed. Put the jointer of the water

inlet hose on the faucet. See to Figure 2. (If the faucet is too large and the jointer can

not be set on the water faucet, please loosen the four screws and take out the

bushing in the jointer. See to the figure.)

1.Press the lower end of the lock lever and push down the slider. Take off the water inlet

hose jointer from the water inlet hose component. See to Figure 1.

Remarks: Before installation, the threading is 4mm above the upper surface of

the nut. After installation, the threading is 2mm above the upper surface of the

nut. See to Figure 6.

4.Take off the nameplate. Twist the fastening nut as per the indication of the figure to

seal up the outlet end surface of the faucet. See to Figure 5.

3.Fasten the four screws evenly. See to Figure 4.

>10mm

Outlet end surface

Nut

About 4mm before twisting

About below 2mm after twisting

Screw

Screwdriver Mark label Liner

Figure 2

Figure 5

Figure 1

Figure 4

Figure 3

Figure 6

Slider

Water inlet pipe jointer

Water inlet pipe

Locking lever

Before Using

Install the water inlet hose

Confirm the water faucet

Connection between the water inlet hose jointer and

the water faucet

1.Do not take off the water absorption

cushion. Please check if the cushion

is dropped or damaged before each

usage. If it happens please contact

our after-sale department immediately.

2.Put the nut of the water inlet hose on

the valve jointer.

3.Fasten the nut. Swing it gently to

confirm if it's suitable.

1.Close the water faucet.

2.Press the locking lever. Push down the slider. Then

pull of the water inlet hose. If the machine is used

more than once every week, the jointer of the water

inlet hose can be kept on the faucet to prevent

damaging the fixing screw.

1.Swing the hose gently to confirm if it is fastened stable.

2.After installation, open the faucet to check if it leaks.

3.Do not bend the hose with overstrain.

4.Before each usage please check if

the connection between the jointer

of the water inlet hose and the water

faucet, and the installation of the

water inlet hose are firm, so as to

prevent dropping from improper

Installation position.

1.Push down the slider. Insert the

water inlet hose into the jointer.

2.Hang the lock lever to the jointer.

Release the slider till a click

sound is heard.

Locking lever

Slider

Water absorption cushion

Nut of the water inlet hose

Jointer of the water inlet valve

Slider

Jointer of the water

inlet hose

Locking lever

Before Using

Connection between the water inlet hose and the

washing machine

Connection between the jointer of the water inlet

hose and the water inlet hose

Check the connection between the jointer of the

water inlet hose and the water faucet

Dismantle the water inlet hose

Preparation before washing

1. Connect the water inlet hose.

2. Confirm that the washing machine is earthed

reliably. Then insert the power plug into the

receptacle. Do not connect the earth terminal

to the gas pipe and tap water pipe.

3.Put down the drain hose.

Using process

1 Preparation before washing

Pay attention to followings before washing the laundries

a. Check if the laundries are applicable for washing with the machine.

b. Divide the laundries with unfast color from other laundries.

c. Put those laundries difficult to absorb water into water with hand.

d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,

please apply detergent in advance, which can make it easier to remove the soil.

e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.

f. Do not put those laundries polluted by chemicals directly into the washing machine.

g. For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into

mesh bag for washing.

Confirm if there's

special requirement

for the laundries.

Clear the pocket.

Take out the coins,

sand, hairpins etc.

Fasten the buttons

and zippers.

The quantity of the

laundries shall not

exceed the rated value.

The big laundries like

the jeans shall be put

in loosely.

When the pulsator is

running, the buttons of

the laundries may cause

noise. For the sake of

discretion, please put

the laundries with

buttons into other

laundries.

Reference weight of the laundries:

working suit(up,down)

Jeans(about 800g)

The capacity of washing and spinning of the

machine refer to the largest weight of the standard

laundries under dry condition (as per the

laundries stipulated in the A2 Attachment of

GB4288-1992 standard) that can be washed or

spun in one time. One time washing quantity

shall be lower than the rated capacity. The largest

capacity of this machine is 5.0kg.

The thicknesses, size, type of the cloth will influence

the actual washing capacity. It is suitable for one

time washing to put in reasonable amount of

laundries and the laundries can be turned round in

washing.

Do not select 4 water level or above for laundries

smaller than 1.0kg, so as to avoid splashing of water.

blending coat

(about 800g)

Shirt Jacket

single bed sheet

Socking

Underpants

Undershirt

Pajamas

Blanket

cotton, about 900g

(cotton, about

300g)

(cotton, about

800g)

(cotton, about 600g)

(blending, about 50g)

(cotton, about 70g)

(cotton, about 180g)

(About 200g)

Using process

2 Put in the laundries

(cotton, about 1120g)

Table of contents

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide