Haier HWM80-27S User manual

High head , unique shape

Full plastic shell

Spraying spin

Separating water and electricity , wide voltage range design

Enclosed base frame , mute design

Bubble wash

With castor

Features

Twin-tub Washing Machine

SERVICE MANUAL

HWM80-27S

Models

Serial Number:SMHWM80-27S-01 Edition: 2005-8-26

Version:00.00

1.Contents 1

2. 1

4. Specifications 3

6. 6

7. Net dimension 7

8. 8

9. Parts and functions 11

10. Maintenance service and trouble shooting 12

11. Wiring diagram 15

12. Exploded view 16

Product code illumination and series introduction

Features 2

Safety precautions 5

Warning and cautions

Installation and accessory parts

CONTENTS

Twin-tub Washing Machine

Model:HWM80-27S

High head, unique shape

Spraying spin

Separating water and electricity, wide voltage range design

Enclosed base frame, mute design

Unique bubble design, remove all dirty

Full plastic shell, stainless for ever

Wide range voltage design, not be afraid of voltage fluctuating

With roller, move easily

Achieve separating water and electricity, more safety

The machine has completely sealed basement, to eliminate noise, more quiet.

FEATURES

Twin-tub Washing Machine

Model:HWM80-27S

SPECIFICATIONS

Twin-tub Washing Machine

Model:HWM80-27S

Model HWM80-27S

Free standing

Built under ×

EAN code

Energy efficiency class

Features for use

Wash capacity kg 8

Spin capacity kg 7

Level/Volum e L55/46/36

Preset H×

Residual dampness %<115

Contral model

contraller

Normal com puterized ×

Fuzzy computerized ×

Frequency conversion ×

Service features

Programs -

Short cycle ×

Inlet heating select

Heating selection ×

Spinning cycle (selector) 1350

Spinning cycle (variable) -

Start/Pause ×

Automatic balncing ×

Aesthetics

Cabinet material P=Plastic/Z=Zincking/C=Cold ) P

Rolled stainless steel

r drum (stainl. steel=s / plastic=p) P

Drain type Down

Door (glass=g / plastic=p) ×

Adjustable feet ×

Technical data

Voltage/frequency V/Hz 220V/50Hz

Energy consumtpion Kwh

Water consumtpion L

Wash power W370

Spin power W230

Special function

Air-Bubble

Feet wheel

Water fall current ×

Dimensions (measurements)

Height / built under mm 948

Width mm 805

Depth / with open door mm 473

Dimensions packed ( measurements packed)

Height mm 995

Width mm 822

Depth mm 492

Net weight kg 25.5

Gross weight kg 30.5

20'Container load Sets 64

40’Container load Sets 130

40H’Container load Sets 160

×"-"FOR BE APPLICABLE

SAFETY PRECAUTIONS

If the power cord is bad, to avoid risk it is required to replace it by the technicians

of our special shop or the after-sale service department. Keep the pin of the power

plug clean.

50 C

Ventilation hole at

the bottom of the

washing machine

Do not use water hotter than 50 C .

Do not share one receptacle with other

electric appliances. Do not use it in

case that the power plug is damaged

or the inserting into the receptacle is

loose.

Earth

Do not wash water-proof laundries such

as the raincoat, bicycle shelter etc. To

avoid abnormal vibration during spinning.

If the power cord is bad, to avoid risk it is required to replace it by the technicians

of our special shop or the after-sale service department. Keep the pin of the power

plug clean.

Be sure to earth the earthing wire reliably.

Do not put the machine at damp place

like the bathroom . Never wash it with

water.Do not place wet laundries on the

control panel.

In case the washing machine is installed

on ground with carpet , do not block the

ventilation hole with carpet.

When the machine is normally using, please

put the power plug at the location easily to

be inserted and extracted by hand. Be sure

to pull the plug off when there'spower failure,

or the machine is being moved, cleaned or

when it is idle.

Twin-tub Washing Machine

Model:HWM80-27S

Do not stretch hands into the working

machine. It is dangerous even if the

rotation is slow. Take special care of

the children.

Handicapped or children without care

shall not use the machine.

Do not put any hot or heavy items

( such as the kettle with hot water )

on the washing machine.

Do not decompose, repair or alter the

machine by yourself.

Keep the machine away from direct

sunlight and heat source like the

heater.

Do not wash laundries with volatile

materials (such as thinner, petrol etc.).

Petrol

Thinner

WARNING AND CAUTIONS

Twin-tub Washing Machine

Model:HWM80-27S

Unit mm

Figure 1

NET DIMENSION

The drainage shall be smooth with the drain hose.

4.If extra drain hose is needed , the inner

diameter of the extra hose shall not less

than 30mm, and the length shall not exceed

1.5m.

<10cm

> 30mm

<1.5m

1.The height of the drain hose shall be

less than 10cm , or the drainage will

not be smooth enough and cause

incomplete drainage.

2.Do not step on or press the drain hose.

3 If the drain hose is too long, cut it at mid

point. To make smooth drainage, cut the

front end of the hose slantingly.

INSTALLATION AND ACCESSORY PARTS

Usage of the drain hose(for drain down washing machine only)

Model:HWM80-27S

Twin-tub Washing Machine

948

805

473

How to change the direction of the drain hoses

Figure 1 indicates the ex factory

installation position of the drain

hose.

Then hang the drain hose into the hanging

hole at the spin tub side. (As per Figure 5).

Extend the drain hose from the side of spin tub.

Extend the drain hose from the rear side

Take out the drain hose from the fixing

hook. Extend it from the rear side (When

the drain hose is extended from the rear

side, it can be hung on the point for drain

hose at the two sides of the cabinet.)

(See to Figure 6).

Take off the drain hose from the hanging

hole of the cabinet. Pull the drain hose

fixing hook outwards gently to take out

the drain hose from the two fixing hooks.

(As per Figure 2)

Rotate the drain hose fixing hook for 90

to take it out from the installation hole

(As per Figure 3).

Install the two drain hose

fixing hooks taken out into

the installation hole at the

other side of the base frame

(to aim at the installation

hole accurately you can

lean the washing machine

forward slightly).Then rotate

for 90 (As per Figure 4).

Pull the fixing hook outwards slightly.

Inlay the drain hose into the fixing hooks

reliably along the groove at spin tub side,

and make it extend towards spin tub side.

Figure 7

Figure 6

Figure 5

Figure 3

Figure 2

Figure 4

Drain hose

fixing hook

Drain hose

fixing hook

Pull outwards

slightly

Side sectional view

Fixing hook

installation hole

Drain hose

Take off

the drain hose

Rotate the fixing

hook for 90 Rotate the fixing

hook for 90

Insert the fixing hook into the

installation hole upwards

Take off the fixing

hook downwards

to fix it

INSTALLATION AND ACCESSORY PARTS

Model:HWM80-27S

Twin-tub Washing Machine

Spin tub shaft

Bearing seat

Figure 10

Oilite bearing

Inner lining of

the bearing seat

Fastening screw

Fastening screw of

the brake wheel

Inner lining of the

brake wheel

Brake wheel

Spin motor shaft

Points of Attention in After-sales Service

Be sure to switch off the power during dismantling or repair.

Be sure to use insulated wiring terminals and insulation box in connection of the wires, and

crimp and fix to proper position with suitable tools.

In welding connections with electric iron, be sure to twist the wires before welding, and insulate

with insulation tapes.

In welding the wires with electric iron, be sure not to touch the resin part and insulation part of

each switch.

The inlay connection wires and terminals shall not be loose or drop.

Do not make the wires touch the moving parts like the belt, pulley of the motor, brake bar etc.

Do not make the wires touch the sharp edges and high-temperature area.

In case that there are metal parts with the wires, do not make the wires touch the metal parts.

Insulation materials are needed between them.

After assembly, the washing machine shall act normally. Check if it leaks and if the sound and

vibration are normal.

Dismantling and installation of the control panel component

Loosen the fastening screws. Pull towards the direction

indicated in the figure to dismantle the control panel. In

installation the beard shall lock into the installation hole

of the major frame. (Figure 8)

Dismantling and installation of the spin tub

frame component

Push the points marked with " " as indicated in

the figure and pull the spin tub frame towards

upper left direction to dismantle the spin tub frame

components. In installation, after set the rear side

of the spin tub frame to proper position, push the

four points marked with " " downwards by force

to resume its original position. (Figure 9)

Dismantling and installation of

the spin tub

Dismantle the spin tub frame component.

Loosen the fastening screw of the spin tub

shaft. The spin tub then can be taken out.

In installation, be sure to inlay the bulge of

the inner lining of the brake wheel into the

groove of the spin tub shaft. (Figure 10)

Figure 8

Spin tub frame

Dismantle Installation

Figure 9

Model:HWM80-27S

Twin-tub Washing Machine

Adjust the tension of the belt

Loosen the fastening screw at the back of the

base frame. Move the shift fixing gasket along

the direction indicated in the figure to adjust

the tension of the belt. After adjusting, fasten

the screw. (Figure11)

Dismantling and installation of the base frame

Dismantle the back cover. Loosen the wires. Loosen the

fastening screw of the spin tub shaft. Separate the shaft

from the brake wheel. Loosen the brake hook. Take off

the brake cable frame from the installation groove of the

twin-tub. Take off the V-belt. Take out the drain hose from

the groove of the base frame. Loosen the fastening screw

between the base frame and the cabinet to dismantle the

base frame component.

Dismantling and installation of the bearing seat

Once the bearing seat is taken off, it can not be utilized again. Therefore do not dismantle

it as far as possible. In case that it has to be replaced, please dismantle it as per following

sequence, then install a new bearing seat.

Dismantle the spin tub as page 9. Then pull out the bearing seat.

Cut off the inner lining claw inside the bearing seat with cutting pliers and take it out.

Install the new bearing seat and inner lining.

The bearing seat is an inlay component. Be sure to aim the claw of the inner lining at the

hole of the tub then push it in. Please use suitable tools and add even pressure around

the tub.

After inlay the bearing seat, check if the claw is installed to proper position from the outside

of the twin-tub (Figure 12).

Figure 11

Figure 12

Right Wrong

Screw

Model:HWM80-27S

Twin-tub Washing Machine

Other manuals for HWM80-27S

Table of contents

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide