Haier HPU-36C13 User manual
Please read this operation manual before using the air conditioner.
No.0010578425
Operation & Installation Manual
CABINET TYPE AIR CONDITIONER
Please keep this manual carefull and safel .
HPU-36H13
HPU-36C13
HPU-44H13
HPU-44C13
Content
Operation
Cautions
Parts
Operation
Operation hints
Energy saving
Maintenance
Trouble shooting
When problems occur
Indoor & outdoor unit connection
Tools necessary
Installation procedures
5 12
13
14
17
20
1 2
3 4
15 16
18 19
21
22 27
Others 28
Cautions
1
Disposal of the old air conditioner
Before disposing an old air conditioner
that goes out of use, please make sure
it's inoperative and safe. Unplug the air
conditioner in order to avoid the risk of
child entrapment.
It must be noticed that air conditioner
system contains refrigerants, which
require specialized waste disposal. The
valuable materials contained in a air
conditioner can be recycled. Contact
your local waste disposal center for
proper disposal of an old air conditioner
and contact your local authority or your
dealer if you have any question. Please
ensure that the pipework of your air
conditioner does not get damaged prior
to being picked up by the relevant
waste disposal center, and contribute
to environmental awareness by
insisting on an appropriate, anti
pollution method of disposal.
Disposal of the packaging of your
new air conditioner
All the packaging materials employed
in the package of your new air
conditioner may be disposed without
any danger to the environment.
The cardboard box may be broken or
cut into smaller pieces and given to a
waste paper disposal service. The
wrapping bag made of polyethylene
and the polyethylene foam pads
contain no fluorochloric hydrocarbon.
All these valuable materials may be taken
to a waste collecting center and used again
after adequate recycling.
Consult your local authorities for the name
and address of the waste materials
collecting centers and waste paper
disposal services nearest to your house.
Safety Instructions and Warnings
Before starting the air conditioner, read
the information given in the User's Guide
carefully. The User's Guide contains very
important observations relating to the
assembly, operation and maintenance of
the air conditioner.
The manufacturer does not accept
responsibility for any damages that may
arise due to non observation of the
following instruction.
Damaged air conditioners are not to
be put into operation. In case of doubt,
consult your supplier.
Use of the air conditioner is to be
carried out in strict compliance with the
relative instructions set forth in the User's
Guide.
Installation shall be done by professional
people, don't install unit by yourself.
2
The machine is adaptive in following
situation
Applicable ambient temperature range:
Cautions
Cooling
Heating
Indoor
outdoor
Rated Maximum Minimum
27 32 18
19.5 23 14
35 43 10
24 26 6
20 27 15
15 15 --
7 21 -7
6 15 --
DB C
WB C
DB C
WB C
Indoor
outdoor DB C
WB C
DB C
WB C
For the purpose of safety, the air
conditioner must be properly grounded
in accordance with specifications.
Always remember to unplug the air
conditioner before opening inlet grill.
Never unplug your air conditioner by
pulling on the power cord. Always grip
plug firmly and pull straight out from
the outlet.
All electrical repairs must be carried
out by qualified electricians.
Inadequate repairs may result in a
major source of danger for the user of
the air conditoiner.
Do not damage any parts of the air
conditioner that carry refrigerant by
piercing or perforating the air
conditioner's tubes with sharp or
pointed items, crushing or twisting any
tubes, or scraping the coatings off the
surfaces. If the refrigerant spurts out
and gets into eyes, it may result in
serious eye injuries.
Do not obstruct or cover the
ventilation grille of the air conditioner.
Do not put fingers or any other things
into the inlet/outlet and swing louver.
Do not allow children to play with the
air conditioner. In no case should
children be allowed to sit on the
outdoor unit.
Specifications
The refrigerating circuit is leak proof.
˛´¶¨+ ‰¡¿
˛´¶¨-
Parts
3
1
2
1
2
1
2
3
4
2
1
2
3
4
I n d o o r u n i t
Remote controller
Outlet grill
Operation panel
Inlet grill
Air filter [inside the unit]
Outdoor unit
Inlet grill
Outlet grill
ON
OFF
TEMP
HEALTH FAN
MODE
SLEEP SWING
CLOCK
TIMER
SET
LOCKLIGHT
RESET
HEAT
SLEEP
POWER/SOFT
HEALTH AIRFLOW
FRESH
CODE
ON/OFF MODE FAN TEMP + TEMP HEALTH
SET
HUMI
TEMP
HEALTH
TIMER
SLEEP
TEMP
HUMI
SET
SLEEP
TIMER
HEALTH
ON/OFF MODE FAN
SET
TEMP
HUMI
HEALTH
TIMER
Parts
Manual Operation
MODE
CLOCK
Used to set correct time.
ON
OFF
TEMP
HEALTH FAN
MODE
SLEEP SWING
CLOCK
TIMER
SET
LOCKLIGHT
RESET
Power ON/OFF
Used for unit start and stop.
Used to select AUTO run,
COOL, DRY,HEAT and
FAN operation.
2
Batter Capacit displa
Displa when the electric power
of the batter is insufficient.
Power/Soft operation displa
Humidif ing displa
Clock displa
Temperature displa
Used to displa the set
temperature and room
temperature.
Lock state displa
Electric Heating displa
2
HEAT
29
HEAT
Fresh Air state displa
Select Auxiliar
electric heater
1
1
3
3
4
5
TIMER
LOCK
Used to select
TIMER ON, TIMER
OFF, TIMER
ON/OFF.
Used to lock buttons
and LCD displa .
4
5
6
7
8
9
10
11
12
LIGHT
SLEEP
Used to select sleep
mode
HOUR
Used to set clock and
timer setting.
RESET
Used to reset the
controller back to
normal condition.
SET
Used to confirm
Timer and Clock
setting.
HEALTH
Control the light up and go out
of the control panel's
background light source and
control the switch of the buzzer.
Used to set Health operation
function
FAN
Used to select fan speed: AUTO,
LOW FAN, MED FAN, HIGH
FAN.
Used to set UP/DOWN air
sending and RIGHT/LEFT air
sending direction.
SWING
6
7
8
9
10
11
12
13
13
14
15
16
17
18
19
21
22
21 23
24
25
26
23
24
27
25
26
29
28
20
BA
28
27
22
4
Note: These models don't have the following related displa and function
For some air conditioners , the function is not availed.
22 28
27
11 29
32
31
HEALTH AIRFLOW
FRESH
POWER/SOFT
30
CODE
33
POWER/SOFT
Used to select HIGH or SOFT operation
30
FRESH
Used to set fresh mode, the unit will
draw in fresh air
31
HEALTH AIRFLOW
Used to set HEALTH AIRFLOW
function.The function is not available
for these units UP/DOWN swing will
not available if this button has been
pushed, please press this button some
times to cancel this mode
32
CODE
Used to select Code A or B,
this manual is for Code A
33
32
Used to set temp.,temp.
range:16 C~30 C
TEMP
Health displa
Displa when set Health
operation function.
Timer ON/OFF displa
Fan speed and air sending
direction displa
Swing direction displa
Room temperature displa
Sleep state displa
LOW MID HIGH AUTO
14
15
16
17
18
20
19
5
1
2
3
Operation
Clock set
When unit is started for the first time
and after replacing batteries in remote
controller, clock should be adjusted as follows:
Press CLOCK button, "AM"or "PM" flashes.
Press or to set correct time. Each press will increase
or decrease 1 min . If the button is kept pressed, time will
change quickly.
After time setting is confirmed, press SET, "AM" and "PM"
stop flashing, while clock starts working.
Remote controller's operation
When in use, put the signal transmission
head directly to the receiver hole on the
indoor unit
The distance between the signal transmission
head and the receiver hole should be within
7m without any obsacles as well.
Don't throw the controller, prevent it from
being damaged.
When electronic started type fluorescent
lamp or change over type fluorescent lamp
or wireless telephone is installed in the room,
the receiver is apt to be disturbed in receiving
the signal so the distance to the indoor unit
should be shorter.
MODE
SLEEP SWING
CLOCK
TIMER
SET
LOCK
LIGHT
RESET
2R 03 dry batteries
MINUTES
HEAT
12
3
Confirmation indicator:
In disorderation, reload the batteries or load the new batteries
after 5 mins.
Note:The waster batteries should be disposed properly,use two
new same type batteries when loading.
If the remote controller cant function normally or doesnt work at
all,use a sharp pointed item to press the reset key.
Hint:Remove the batteries in case unit wont be in usage for a long period.
If there are any displays after taking out just need to press reset key.
When throw away the waste batteries, please perform in accordance with the local regulation.
Loading of the battery
Slightly press " " and push down the cover.
Load the batteries as illustrated.
2 R 03 dry batteries, (cylinder)
Be sure that the loading is in line with the "+"/" " pole
request as illustrated.
Put on the cover again.
HEATH AIRFLOW
FRESH
CODE
POWER/SOFT
Remote
controller LOW MID HIGH AUTO
Operation
2.
1.
Press ON/OFF button
Unit starts running.
The pre ious status appears on the display
(except. TIMER, SLEEP mode)
Press MODE button.
For each press, operation mode changes as follows:
5.
Remote
controller AUTO COOL DRY FAN HEAT
Press FAN
For each press, operation mode changes as follows:
Unit runs at the speed displayed on LCD.When fan speed is AUTO,
it is changed automatically,according to the indoor temperature.
Note:
During Auto run operation, temp. setting will be shown in LCD display, unit will select heating, cooling
or fan operation according to the room temp.
6.
6
Select temp. button
Press TEMP button
E ery time the button is pressed, temp. setting increases 1¡
E ery time the button is pressed, temp. setting decreases 1¡
If the button is kept pressed, setting will increase or decrease quickly.
3.
In DRY mode, when room temp.becomes 2 C higher than temp.
setting,unit will run intermittently at LOW speed regardless of FAN
setting.
Ultra low air flow
Temp.setting+2 C
Temp.setting
COOL operation starts when room
temp. is higher than temp. setting.
On reaching 2 C higher than temp.
setting,unitwill run in mild DRY mode.
ON
OFF
TEMP
HEALTH FAN
MODE
SLEEP SWING
CLOCK
TIMER
SET
LOCKLIGHT
RESET
2
6
HEAT
Then select AUTO run or select COOL operation or
select DRY operation or select HEAT operation
AUTO COOL DRY FAN
ON
ON
13
5
3
Control panel HEAT
TEMP+
TEMP-
The fan speed change of the control panel see page 12.
Press ON/OFF button Unit stops running.
4
(During Cooling ,Fan , Dehumidification etc. Operations ,this function
cant be operated.)
Press the button of HEAT ,remote controller & LCD display ,this
function start to runing.Press this button another time , remote controller
& LCD display will be disappears,this function stops.The Auxillary
heating condition see the page 13 of this manual.
4.
Auxillary heating function(only Suit for the units with
Auxillary heating function models)
HEALTH AIRLOW
FRESH
POWER/SOFT
CODE
1
5
33
24
ON/OFF MODE FAN HEALTH
TEMPTEMP
TEMP
7
Operation
Fan Operation
3. Adjust fan speed
Press FAN button. At each press, fan speed changes as
follows:
Air conditioner will run at the selected fan speed.
4. Unit stop
Press ON/OFF button to stop unit.
Then select FAN
About FAN mode
When the air conditioner runs in FAN mode,
it is not possible to select AUTO FAN or to
set temperature.
Manual Operation
Remote-control unit
ON
OFF
TEMP
HEALTH FAN
MODE
SLEEP SWING
CLOCK
TIMER
SET
LOCKLIGHT
RESET
2
4
HEAT
1
3
AUTO COOL DRY FAN HEAT
Control panel
POWER/SOFT
CODE
HEATH AIRFLOW
FRESH
LOW MED HIGH
1.Unit start
Press ON/OFF button to start our air conditioner.
Previous operation status appears on LCD (except for
TIMER, SLEEP, setting).
2.Select operating mode
Press MODE button. At each press, operation mode
changes as follows:
AUTO FANHEATCOOL DRY
1
4
2
ON/OFF MODE FAN TEMP TEMP HEALTH
3
TEMP
8
Up & down air direction
Press the up & down button once, the LCD aiflow direction will display as follows:
Cooling/Dehumification/airflow:
Remote controller: Position 1 2 3 4 6
Heating: Position 5 4 3 2 1 6
Remote controller
Auto:
Remote controller:Position 1 2 3 4 5 6
The up & down flade will move according to the above conditions.
Note: Pay more attention to not cut down the power supply because the flade can't back to the
colse position at this circumstance;
Left & right air direction
Press the Left & right button once , the LCD aiflow direction will display as follows:
Remote controller: Position 1 2 3 4 5 6 7 8
The left & right flade will move according to the above conditions
Note: 1. during AUTO mode, pls. don't touch the flade to avoid damaging the inner part of the unit;
2. If the difference between real position & the chart position, press ON/OFF(control panel) button
or ON/OFF( remote controller) button to close the flade and re open the unit, then it will be normal condition.
(not availble in these nuits)
(not availble in these nuits)
ON
OFF
TEMP
HEALTH FAN
MODE
SLEEP SWING
CLOCK
TIMER
SET
LOCKLIGHT
RESET
HEAT
1
POWER/SOFT
2
Up and down Side from side
Position 1
Position 2
Position 3
Position 4
Position 5
Position 6
Position 7
Position 8
[COOL/DRY/FA
N/AUTO(COOL)
HAVE NOT]
(AUTO SWING)
Position 1
Position 2
Position 3
Position 4
Position 5
Position 6
Operation Air flow adjustment
Swing louvers
(Vertical louvers)
(Horizontal louvers)
CODE
HEATH AIRFLOW
FRESH
This manual suits for next models
3
Other Haier Air Conditioner manuals
Haier
Haier AS25THMHRA-C User manual
Haier
Haier HSU-18LXA03 User manual
Haier
Haier HSU-12H03 User manual
Haier
Haier AF092XCERA User manual
Haier
Haier HSU09XCA User manual
Haier
Haier 1U71S2SG1FA User manual
Haier
Haier HSU-07LEK03 User manual
Haier
Haier AU242FHBHA User manual
Haier
Haier AW09ES2VHB User manual
Haier
Haier HC1891VAR User manual
Haier
Haier HSU-18H03-R User manual
Haier
Haier HWF05XC7 Instruction Manual
Haier
Haier AP88NACAAA User manual
Haier
Haier HSU-09LA03 User manual
Haier
Haier HR18D2VAR User manual
Haier
Haier HFM12HC03 User manual
Haier
Haier HWF05XC7 User manual
Haier
Haier HWR12XC9 User manual
Haier
Haier HPM09XC5 - 11-04 User manual
Haier
Haier AB09CS1ERA User manual
Popular Air Conditioner manuals by other brands
Fujitsu
Fujitsu Inverter ASBA30JFC operating manual
Toshiba
Toshiba RAS-M10SMUV-E installation manual
Daikin
Daikin FXLQ20MAVE Operation manual
Hitachi
Hitachi RAS-E24CAK instruction manual
CIAT
CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance
Bestron
Bestron AAC6000 instruction manual
