Haier AP88NACBEA User manual

Cabinet unit

Operation Manual

AP88NACBEA

AU88NATBEA

No.0010573003

Operation points

Name of Parts

Safety Precautions

Operation instruction

Users' Attention

Maintenance

Trouble shooting

When problems occur

When troubles occur

Installation instruction

Installation procedure

Others

2-3

4-5

6-10

12-13

18-30

31-32

CONTENTS

MODEFAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

Change of fan speed

In COOLING mode, the air sending is set at AUTO,

when the indoor temperature is near the set temperature,

the fan speed will lower automatically.In HEATING

mode, when room temperature reaches the

set temperature, the compressor will stop

running, and the fan will change to LOW

FAN or stop.In DEHUMIDIFYING mode,

the fan speed will change automatically.

3-minute protection function

If start the unit immediately only

after it is turned off, the compressor

will start

after 3

minutes have

elapsed to protect

the compressor.

Operation of air conditioner

When the ambient

humidity is too high,

in COOLING or

DEHUMIDIFYING

mode, there may be water

dropped in the air outlet.

Anti-cold air blowing out

During Heating operation, after starting the

unit, the indoor fan motor

will not rotate immediately

to prevent

cold air from

blowing out.

Defrosting function

During Heating operation, when frost formed on the

heat exchanger of outdoor unit, the air conditioner

will defrost automatically for several minutes. During

defrosting, both the fan of indoor and

outdoor unit do not run. After

finishing defrosting, the air

conditioner will automatically

resume operation.

Hint

When the air conditioner

is in Heating mode, it

absorbs heat from

outside and release to

indoors. So the outdoor

temperature may affect

the Heating effect.

Power failure resume function (please set and use this function according to actual

condition)

After setting power failure resume function, if there is a sudden power failure during

unit operation, when power on for again, the unit will resume the previous state.

Setting method:when the wire controller is in ON state (except for TIMER and FAN

mode), press the SLEEP button for 10 times in 5 seconds, after the buzzer sounds 4

times, the unit will change to POWER FAILURE RESUME function.

Cancellation method: press the SLEEP button 10 times in 5 seconds, after the buzzer

2 times, the POWER FAILURE RESUME function is cancelled.

Note:After the unit is set POWER FAILURE RESUME function, if there is a sudden power failure

in using, during this period of time if there is no need to use the unit for a long time, please cut off

power to prevent the air conditioner from automatically resuming to the previous setting if powerfailure

resumes, or press the ON/OFF button to turn off the unit after power failure resumes.

Operation points

MODEFAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

MODEFAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

MODEFAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

MODEFAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

Outlet grill

Operation panel

Inlet grill

Indoor unit

Outdoor unit

Air inlet

Air outlet

Name of Parts

The interface of the refrigerant pipe

Note:

Open the power switch 12 hours before the unit running.Do not cut off the power

when short time stop the unit (like one day and one night ),this is to protect the

compressor.

Do not block the air inlet and air outlet, otherwise the performance of the air

conditioner may be lowered and it will make the protection device act.

MODE FAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

Name of Parts Wire Controller

14.Network control display

Used to adjust the

time of timer and

clock

When the wire

controller appears

abnormal condition,

use a sharp-pointed

article to press this

button to make the

wire controller

resume normal

After cleaning the

air inlet, press this

button, the unit

can start to operate

12.Humidifying state display

Used to turn on/off unit

1.ON/OFF button

6.Air filter cleaning display

7.Super/Soft operation display

13.Sleep state display

2.Temperature display

24.Time Adjusting

button

23.Sleep button

Used to set Sleep

state or Power

Failure Resume

Function

When there is too much dust

collected on the air inlet, the

wire controller will show

this display to remind the

user to clean the air inlet.

After cleaning and installation,

just press the air filter reset button.

8.Fan speed display

9.Auto Swing display

11.Fresh air state display

25.Reset button

26.Air Filter Reset

button

27.Timer button

Used to set the

mode of timer

29.Lock state display

28.Electric heating button

4.Timer ON/OFF display

3.Clock display

17.Operation mode button

5.Humidity display

22.Setting button

Used to confirm

the time of timer

and clock

15.Working mode display

21.Clock button

Used to calibrate the time of

timer and clock

16.Electric heating display

Used to set working mode:

Auto, Cooling, Dehumidifying,

Heating, Fan

18.Fan speed button

Used to set fan speed: Low

Fan, Med Fan, High Fan, Auto

20.Temperature Setting button

10.Health state display Used to set temperature,

temperature range: 16*~30*

19.Swing button

Used to set Auto Swing or

Fixed air sending direction

Note:

1.This model does not have the following related display and function

2.Non-electric heating type, there is no electric heating button and electric heating

display

* * 10 11 12

Auto

Low Fan Med Fan High Fan Auto

Working

mode Auto

operationCooling

operation Dehumidifying

operation Heating

operation Fan

operation

Wire

controller

Calibration of clock

When turning on the unit for the first time, the clock should be calibrated. The

method of calibration is:

1.Press ì Clockî button, the Clock display ì AMî ì PMî will flash.

2.Press *or to adjust time. For each press, the time will increase or decrease 1

*minute. If depressing the button, the time will increase or decrease rapidly.

3.After confirming the time, press ì Setî button, ì AMî or ì PMî will stop flashing,

*the clock will begin to work.

SET

ROOM

AUTO

MODE FAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTER RESET

RESET

ON/OFF

HEAT

Safety Precautions

Before starting the unit, please read the following ì Safety Precautionsî carefully

to guarantee the normal operation of the system.

The following lists two kinds of safety precautions ì Warningî and ì Noticeî .

For the items that the improper use may cause death or serious injury are listed in

ì Warningî volume. However, sometimes the items listed in ì Noticeî volume

may also cause serious accidents. So, these two volumes are the important contents related

to safety, they must be observed.

Installation Safety Precautions

Warning

The system should be applied to places as

office, restaurant, residence

and the like.

The system should be installed by your

dealer or a professional installer.

Application to inferior environment

such as workshop, it may cause equipment

malfunction and serious injury or death.

Installation by yourself is not encouraged.

Because improper installation could cause

water leakage, electric shock and fire accident.

Notice

Operation safety precautions

Do not let the cold wind blow to human

body for a long time. When any abnormal condition (scorching smell or

others) is found, stop operation

immediately and turn off the

power switch. Then consult your dealer.

Warning

It may affect the physical condition or

cause some health problems.

If continuing the operation without removing the

cause, it may cause trouble, electric shock or fire.

After carefully reading this manual, please keep in hand for reference. If the air

conditioner is given to a new user, this manual should be attached with unit to

the new user.

Grounding wire should never be

connected to gas pipe, city water pipe,

lightning conductor rod or the

telephone line. If the grounding wire

is not set properly, it may cause

electric shock.

OFF

A creepage breaker must

be installed at the

installation place

Drain pipe should be arranged

properly to provide a smooth

drainage.

Unless the circuit

breaker is installed, it

may cause electric

shock.

If the pipe is

arranged improperly,

furniture or the like may be

damaged by the leaked water.

Make sure the system is grounded.

Notice

Do not handle switches with a wet hand.

It may cause electric shock.

Do not use water to clean

the air conditioner.

It may cause electric shock.

Do not do like this Do follow the instruction Do equip with grounding wire

Safety Precautions

Notice

The system should never be

used for any other purposes

than intended such as for

preservation of food, flora

and fauna, precision devices

or work of art.

Do not put the fire

devices in the places,

which the air from

the air conditioner

can directly blow.

It may cause deterioration of

the articles.

It may cause the fire

devices cannot burn

completely.

Do not install the system where the air

outlet may directly reach the flora and

fauna.

Only use the proper specified fuse.

It will not be good for their health.

If use metal wire or copper wire to

replace the fuse, it may cause trouble

and fire accident.

Do not put or use any

spray near the air

conditioner, and do not

directly spray to the air

conditioner.

Otherwise it may cause

fire.

Safety precautions when moving, reinstalling and repairing the air conditioner

Warning

OFF

Do not use the pow-

er switch to turn of

or off the air condit-

ioner.

Do not use such equipment as a water heater,

etc., around the indoor unit

or the wire controller.

It may cause fire or

Creepage.

If the system is operated at the vicinity of such

equipment that generates steam, condensed

water may drip during cooling operation or it

may cause Creepage or short-circuit.

When operating the system sim-

ultaneously with a combustion

apparatus, indoor air must be v-

entilated frequently.

Insufficient ventilation may ca-

use the danger of lack of oxygen.

When cleaning, please

stop the unit and cut o-

ff the power first.

Do not put the water containers,

such as vase, on the unit.

Do not perform

cleaning, when the

indoor fan motor is

rotating in high

speed.

If the water enters

into the unit and damages

the electric insulation material,

it may cause electric shock.

Do not refit the air conditioner.

When repair is needed, please

contact your dealer.

When moving the air conditioner to another

installation place, please contact the dealer

or the professional installer.

Improper repair may

cause water leakage,

electric shock and fire accident. Improper moving and reinstallation may cause

water leakage, electric shock and fire accident.

LOW FAN MED FAN HIGH FAN

Operation instruction

MODE FAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTER RESET

RESET

ON/OFF

HEAT

Fan operation

About FAN operation:

FAN operation refers the air conditioner does not perform COOLING and

HEATING operation, but FAN operation. In this mode, the air conditioner

cannot perform AUOT FAN operation, and does show the temperature

value on the wire controller.

Turn on the unit

Press the ON/OFF button to turn on the

unit The LCD display of the wire controller

will show the previous working state

(except for Timer, Sleep, Swing mode), the

operation indicator light on the wire controller

will light up.

Choose of working mode

Press MODE button, each press the

working mode will change as the

following sequence:

choose FAN operation

Adjusting FAN SPEED

Press the FAN SPEED button to change fan

speed:

4Turn off the unit

Press the ON/OFF button to turn off the

unit.

The wire controller only shows the clock and

room temperature.

Choose the desired fan speed

COOLING DEHU

AUTO HEATING FAN

AUTO COOLING DEHUMIDIFYING HEATING FAN

AUTO

LOW FAN MED FAN HIGH FAN AUTO

MODE FAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

HEAT FILTER RESET

SET

RESET

ON/OFF

Hints:

The wire controller can memorize the working condition of each time. When

start the unit for the second time, just need to press ON/OFF button, the air

conditioner will work according to the previous working mode. (except for

Timer, Sleep and Swing)

Operation instruction

Auto/Cooling/Dehumidifying/Heating operation

Turn on the unit

Press the ON/OFF button to turn on the

unit The LCD display of the wire

controller will show the previous

working state (except for TIMER,

SWING, SLEEP mode). The operation

indicator light on the wire controller

will light up.

Choose of working mode

Press MODE button, each press the

working mode will change as the

following sequence:

then choose AUTO, COOLING,

DEHUMIDIFYING, HEATING operation.

Set temperature

*Each press , the set temperature will

increase 1 degree.

*Each press, the set temperature will

decrease 1 degree.

Set the desired temperature.

Press the TEMP. SET button

Adjusting FAN SPEED

Press the FAN SPEED button, for each

press, the fan speed will change as the

following sequence:

Choose the desired fan speed.

In Heating operation, after start

the unit, the air conditioner will

sending warm air a moment

later to prevent the cold air

blowing out. In Dehumidifying,

when the room temperature drops

2*higher than the set

temperature, regardless the set fan

speed, the air conditioner will

intermittently operate in low fan

speed.

5Turn off the unit

Press the ON/OFF button to turn off

the unit.

The wire controller only shows the clock

and room temperature.

Set temperature + 2*

Set temperature

When room temperature

reaches set temperature

+ 2*, the unit will

operate in mild

dehumidifying

operation.

Ultra-low air flow

When room temperature

is higher than set

temperature, unit in

COOLING operation.

Note:

MODE FAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

HEAT FILTER RESET

SET

RESET

ON/OFF

Operation instruction Sleep operation

Use of SLEEP function

After turning on the unit, setting the working mode, then press SLEEP button to

make the air conditioner have the previous Sleep time (powered on for the first time

or after performing Sleep is 1h). The Sleep symbol will appear. Press time */*

button, you can choose between 1~8h. Each press, it may increase/decrease 1h and

will display in the humidity area with ì xhî , and display ì Timer Offî in Timer Off

area and the time to turn off; press Sleep button again to cancel Sleep function. The

Sleep symbol disappears.

Before going to bed, you can press the SLEEP button, the air conditioner will operate

in comfort sleep mode to make you have a sound sleep.Before using this function, you

should calibrate the clock first, otherwise, the SLEEP function will be out of order.

2.In HEATING operation

1 hour later in SLEEP operation, the temperature

will decrease 2*from the set temperature, another

1 hour later increase another 2*, then the unit will

operate continuous at this temperature for 3 hours,

then it increases 1*, after operating at this

temperature for another 3 hours, the unit will turn

off automatically. The temperature is lower than set

temperature to prevent you from feeling

uncomfortable during sleep.

3.In AUTO operation

The air conditioner will perform the relative SLEEP operation

according to automatically chosen operation mode.

4.In FAN operation

Cannot use SLEEP function

Operation modes

1.In COOLING, DEHUMIDIFYING operation

1 hour later in SLEEP operation, the temperature

will increase 1*from the set temperature, another

1 hour later increase another 1*, then the unit will

operate continuous for 6 hours, then it turns off

automatically. The temperature is higher than set

temperature to prevent you from getting a cold.

After setting Sleep function, it is not permitted to adjust clock.

The Sleep time is less than 8h, after reaching the set time, the unit will automatically stop.

Set Sleep function after setting ì Timer Offî function, the air conditioner will perform Sleep

function.

After setting Sleep function, the Timer function cannot be set.

Set Sleep function after setting ì Timer Onî function, the Sleep function can only be set

in the set time of Timer On.

in COOLING*DEHUMIDIFYING operation

Set temperature

SLEEP operation starts SLEEP operation stops

turn off

1 hour

about 6 hours

increase 1*

1 hour

increase 1*

Set temperature

SLEEP operation starts SLEEP operation stops

turn off

1 hour

about 3 hours

3 hours

decrease 2*

increase 1*

in HEATING operation

1 hour

decrease 2*

Timer On/Off function

Operation instruction

OFFON OFFON

TIMER ON TIMER OFF TIMER ON-OFF

Blank

MODE FAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

HEAT FILTER RESET

ROOM

RESET

ON/OFF

Before using TIMER function, calibrate the clock

first (referring to page 4). When you wake up in the

morning, before going back to home after work or

after going to bed, you can let your air conditioner

automatically turn on or turn off.

2.Set of TIMER mode

Press the TIMER button to change the TIMER

mode, each press the TIMER mode will

change as the following sequence:

1.Turn on the unit

Cancel TIMER

Press the TIMER button several times until the TIMER mode display

disappears.

After turning on the unit, set the desired

working mode.

The LCD of the wire controller will show

working mode. (except for Timer, Sleep, Swing)

*Each press, the set time increases 10 minutes. If depress the button, the

time will increase rapidly.

*Each press, the set time decreases 10 minutes. If depress the button, the time will

decrease rapidly.

3.Set time

Press the time adjusting button

This LCD will show the time set, the time can be adjusted within 24h.

(AM stands for morning, PM stands for afternoon).

4.Confirm the time

After calibration of the clock, press SET button to confirm time.

The time displayed is: at x oíclock x minutes the unit will be turned on

(TIMER ON) or turned off (TIMER OFF).

Hints:.

After power failure, the clock should be calibrated again.

The wire controller has memory function, when you use this function for the

second time, if the time set is the same as the previous one, you just need to

choose the TIMER mode then press the SET button to confirm.

At this time, the* *or* *will not flash.

ON OFF

Then choose the timer mode as you need

(TIMER ON or TIMER OFF.)

At this time the or will flash.

ON OFF

" " " "

This manual suits for next models

Table of contents

Other Haier Air Conditioner manuals

Haier

Haier HSU-28HA03/R2 - annexe 1 User manual

Haier

Haier HSU-09HEA03-R2-I User manual

Haier

Haier AD122ALEAA Administrator Guide

Haier

Haier AS71S2SF2FA-1 User manual

Haier

Haier HPY08XCM User manual

Haier

Haier HPF14XCM User manual

Haier

Haier ADH071M1ERG Installation and operating instructions

Haier

Haier HSU--12HD03/R2 User manual

Haier

Haier Super Match AF09AB1HRA User manual

Haier

Haier HPU-42CV03 User manual

Haier

Haier HUM07HA03-R2 User manual

Haier

Haier AB25S2SC1FA User manual

Haier

Haier HWF05XCL User manual

Haier

Haier HSU-09XC7 User manual

Haier

Haier SUPER MATCH AS50S2SF1FA-BC User manual

Haier

Haier AS25S2SJ1FA-3 User manual

Haier

Haier MRV 5 Series User manual

Haier

Haier WJ01X24721 User manual

Haier

Haier HSU-18HVE03 User manual

Haier

Haier HSU-07LEK03 User manual

Haier

Haier HSU-09C03/Z1 User manual

Haier

Haier HSU18VH7 User manual

Haier

Haier HW-09CN03 User manual

Haier

Haier 1U50KEFFRA-1 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual