Grundig GCA-B1322D User manual
GCA-B1322D.1.1.3.11.2010
Owner´s Manual
EN
© ASP AG
Cameras & Domes
GCA-B1322D 1/3" Col/B&W Fixed Dome Camera, Vari-Focal
GCA-B0322D 1/3" Col/B&W Fixed Dome Camera, Vari-Focal
GCA-B0325D 1/3" Col/B&W Fixed Dome Camera, Vari-Focal, WDR
GCA-B0323D 1/3" CCD Col/B&W Fixed Dome Camera w/ IR LED
e
VSS Nederland B.V. - Telfordstraat 11m - 8013 RL Zwolle - Tel.: +31 38 42 89 420 - Fax: +31 38 42 89 429 - E-mail: [email protected]
VSS Nederland
Video Systems
Content:
1. Available Versions 1
2. Important Safety Instructions 2
3. Package Contents 2
4. Installation 3
1. Parts Name 3
2. Base Installation 4
3. Connections 5
4. 3-Axis Gimbal Adjustment 6
5. Zoom & Focus Adjustment 6
5. OSD Menu 6
1. OSD Controls 6
2. Main menu 7
3. Camera Setup 8
4. Intelligence 15
5. Privacy Zone 16
6. Other Set 17
7. Communication 18
8. System Info 18
9. Language 18
1. Available Versions
These instructions apply to the following products. For the different properties of the
products please refer to the table.
1English
2. Important Safety Instructions
Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product. Do not connect multiple cameras to a single
adapter. Exceeding the capacity may cause abnormal heat generation or fire.
Do not place conductive objects (e.g. screwdrivers, coins or any metal items) or
containers filled with water on top of the camera. Doing so may cause personal injury
due to fire, electric shock, or falling objects.
If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued use
in such a condition may cause fire or electric shock.
If this product fails to operate normally, contact the nearest service center. Never
disassemble or modify this product in any way. (GRUNDIG is not liable for problems
caused by unauthorized modifications or attempted repair.)
To prevent fire or electric shock, do not expose the inside of this device to rain or
moisture.
3. Package Contents
These parts are included:
2English
4. Installation
Do not install in a location subject to high temperature (over 50°C), low temperature
(below -10°C), or high humidity. Doing so may cause fire or electric shock. Keep out of
direct sunlight and heat radiation sources. It may cause fire. Avoid aiming the camera
directly towards extremely bright objects such as sun, as this may damage the CCD
image sensor.
Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or
electric shock. Install it in a place with good ventilation.
When installing the camera, fasten it securely and firmly. A falling camera may cause
personal injury.
If you want to relocate the already installed product, be sure to turn off the power and
then move or reinstall it.
4.1. Parts Name
1. Bubble
2. Dome Cover Ring
3. Mounting Screws
4. Camera Module Gimbal Bracket
5. Lens
6. Dome Base
7. Service Monitor Output Port
8. Video Out and Power Cable
3English
4.2. Base Installation
1. Open the dome cover ring at the marked position (e.g. with a flat screw driver).
2. There are three mounting holes on the Dome Base for installation of the unit in any
place such as ceiling, wall and etc. Use the three mounting screws to affix the Dome
Base to a sturdy surface. To access all three holes, rotate the camera module.
4English
4.3. Connections
- Power connection: Requires DC 12V or AC 24V input depending on camera model.
- All camera models are supplied with service monitor output on the camera module. A
service monitor and control cable is included in the package.
Note:
To set up OSD menu externally, service monitor and control cable is required.
5English
4.4. 3-Axis Gimbal Adjustment
1. Pan: Adjust the pan by turning it to the
right or left by hand.
2. Tilt: Adjust the tilt by moving it up or down
by hand.
3. Rotation: Adjust the rotation to the
desired angle by hand.
4.5. Zoom & Focus Adjustment
1. If you need to make viewing angle/focus adjustments, move the levers as shown
below. First loosen the Zoom/Focus levers, and then adjust them as needed.
2. After adjustments, tighten the Zoom/Focus levers.
5. OSD Menu
5.1. OSD Controls
5.1.1. OSD Control Keys
- SETUP key: Accesses to the menu mode
or confirms the setting.
- UP (/\) / DOWN (\/): Chooses the desired
menu.
- LEFT (<) / RIGHT (>): Sets up the value of
the selected menu.
6English
5.1.2. OSD Icons
Exits the menu setting. Before you exit
make sure you SAVE your settings, or
select QUIT to cancel.
Returns to the previous menu.
Returns to the main menu.
Use this to SAVE your settings of MASK
AREA, PRIVACY ZONE and more. Once
you saved your settings, they will remain
even if you select QUIT in the menu.
Use this to delete your settings of MASK
AREA, PRIVACY ZONE and more. Once
you saved your settings, they will not be
restored even if you select QUIT in the
menu.
5.2. Main menu
1. Press the SETUP key and hold it for a while to access the menu mode.
2. Select the desired feature by using UP/DOWN keys (/\ \/) on the control.
CAMERA SET: Here you can configure
camera related functions and data.
INTELLIGENCE: You can configure the
settings of motion detection, tracking and
more.
PRIVACY ZONE: You can configure the
privacy related settings.
OTHER SET: You can configure for factory
defaults, and more.
7English
COMMUNICATION: Configures the settings regarding the RS-485 communication.
SYSTEM INFO: Displays the system information including the camera version and
communication settings.
LANGUAGE: Select a preferred language from those listed.
5.3. Camera Setup
CAMERA ID [OFF, ON] :
It is used to switch on/off the camera id. If
camera id is switched ON you can access
the CAMERA ID menu to programm the
camera text.
IRIS [ALC, ELC] :
The IRIS menu is used if you want to adjust
the intensity of light incoming into the
camera.
MOTION [S.SLOW, SLOW, NORM, FAST, F.FAST] :
This menu is used to adjust the strength of the AGC level for a control of the camera
motion. You can select from S.SLOW, SLOW, NORM, FAST and F.FAST for the AGC
level. If you monitor fast moving objects in a low contrast scene, select F.FAST while
select S.SLOW for hardly moving objects in the same lighting condition.
Note:
- This is only available if the SENS-UP menu is set to AUTO.
- If the DAY/NIGHT menu of CAMERA SET is set to AUTO, the MOTION menu will be
deactivated.
DNR [OFF, LOW, MID, HIGH, USER (1~16)] :
You can configure the DNR (Digital Noise Reduction) related settings. It reduces the
noise on the screen. This is especially useful for a severely distorted screen. You can
set the level if you set DNR to USER.
SENS-UP [OFF, AUTO x2~x256, FIX x2~x256] :
Automatically detects the ambient level of darkness in the dark or low contrast scene to
extend the accumulated time, keeping the image bright and sharp. It can be also used as
FIX mode.
Note:
- If the SHUTTER menu is set to fixed electronic shutter mode, the SENS-UP menu will
be deactivated.
- If the FLICKERLESS menu is set to ON, the FIX mode of the SENS-UP will be disabled.
8English
This manual suits for next models
3
Table of contents
Other Grundig Security Camera manuals
Grundig
Grundig GCA-C0335P User manual
Grundig
Grundig GD-CI-CT12617F User manual
Grundig
Grundig GD-CI-AP2627V User manual
Grundig
Grundig GCA-C0245P User manual
Grundig
Grundig GCA-B1002B User manual
Grundig
Grundig GD-CI-CC4637T User manual
Grundig
Grundig GD-CI-AT4634V User manual
Grundig
Grundig GD-CI-CT4537TH User manual
Grundig
Grundig GD-CI-DT2647T User manual
Grundig
Grundig GD-CI-BP8637T User manual
Grundig
Grundig GD-CI-AC1616V User manual
Grundig
Grundig GCH-K0326T User manual
Grundig
Grundig GD-CI-AP2605B User manual
Grundig
Grundig GD-CT-AC2126V User manual
Grundig
Grundig GD-CI-CC2616V User manual
Grundig
Grundig GD-CI-BC2615M User manual
Grundig
Grundig GD-CT-AC2116T User manual
Grundig
Grundig GCI-F0576TH-1 User manual
Grundig
Grundig GU-CI-AP5647P User manual
Grundig
Grundig GD-CI-AC2616E User manual
