Graco TexSpray 235490 Operating instructions

ti3005c

Repair

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440- 1441

0.9 to 3.0 gpm (3.4 to 11.4 lpm) Flow Rate

750 psi (5.1 MPa, 51 bar) Maximum Working Pressure

500 psi (3.4 MPa, 34 bar) Recommended Maximum Working Pressure

Model 234113, Series C

TexSpray 1030 FC sprayer, 235490 TexSpray gun

and 50 ft (15 m) air and fluid hose set

309662L

‘

CONTENTS

Warnings 2..............................

Component Description 5..................

Maintenance 6...........................

Troubleshooting 7........................

Repair 10...............................

Parts 20.................................

Accessories 26...........................

Technical Data 27........................

Dimensions 27...........................

Warranty 28.............................

308274.......

309663.......

- For portable spray application of architectural paints and coatings -

TexSpray 1030tFC

Important Safety Instructions

Read all warnings and instructions in this

manual. Save these instructions.

German Patent No. P 43 18 679.3--09

2 309662

Specifications

This equipment is not intended for use with flammable or combustible materials used in places such as

cabinet shops or other “factory” or fixed locations. If you intend to use this equipment in this type of

application, you must comply with NFPA 33 and OSHA requirements for the use of flammable and

combustible materials.

Warnings

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

309662 3

The following are general Warnings related to the safe setup, use, maintenance and repair of this equipment.

Additional, more specific warnings may be found throughout the text of this manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help

prevent fire and explosion:

DUse equipment only in well ventilated area.

DEliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic

drop clothes (potential static arc).

DSprayer generates sparks. When flammable liquid is used in or near sprayer or for flushing or

cleaning, keep sprayer at least 20 ft (6 m) away from explosive vapors.

DDo not clean with materials having flash points lower than 70_F(21_C). Use water--based materi-

als or mineral spirits type material only. For complete information about your fluid, request the

MSDS from the fluid distributor or retailer.

DKeep work area free of debris, including solvent, rags and gasoline.

DDo not plug or unplug power cords or turn lights on or off when flammable fumes are present.

DGround equipment and conductive objects in work area. Read Grounding instructions.

DIf there is static sparking or you feel a shock, stop operating immediately. Do not use equipment

until you identify and correct the problem.

SKIN INJECTION HAZARD

High pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like

just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

DDo not point gun at anyone or any part of the body.

DDo not put your hand over the spray tip.

DDo not stop or deflect leaks with your hand, body, glove, or rag.

DEngage trigger lock when not spraying.

DFollow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,

checking or servicing equipment.

PRESSURIZED ALUMINUM PARTS HAZARD

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or

fluids containing such solvents in this equipment. Such use could result in a serious chemical reaction,

with the possibility of explosion, which could cause death, serious injury and/or substantial property

damage.

4 309662

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

DRead all instruction manuals, tags, and labels before operating the equipment.

DUse equipment only for its intended purpose. Call your Graco distributor for information.

DDo not exceed the maximum working pressure or temperature rating of the lowest rated system

component. This gun has a 150 psi (10 bar) maximum fluid working pressure at a 125 psi (9

bar) maximum incoming air pressure. Read Technical Data in all equipment manuals.

DDo not alter or modify equipment.

DCheck equipment daily. Repair or replace worn or damaged parts immediately.

DDo not lift pressurized equipment.

DRoute the hoses away from the traffic areas, sharp edges, moving parts, and hot surfaces. Do not

expose Graco hoses to temperatures above 180_F(82_C) or below --40_F(--40_C).

DDo not use hoses to pull equipment.

DKeep children and animals away from work area.

DComply with all applicable safety regulations.

DDo not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or

fluids containing such solvents in this equipment, which contains aluminum and/or zinc parts. Such

use could result in a serious chemical reaction, with the possibility of explosion, which could cause

death, serious injury and/or substantial property damage.

DWear eye and ear protection when operating this equipment. Keep body parts away from front of

gun. See Sound Data in TECHNICAL DATA.

TOXIC FLUID HAZARD

Toxic fluid or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or

swallowed.

DRead MSDS’s to know the specific hazards of the fluids you are using.

DStore hazardous fluid in approved containers and dispose of it according to all applicable guide-

lines.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating

area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic

fumes, burns, and hearing loss. This equipment includes, but is not limited to:

DProtective eye wear.

DClothing and respirator as recommended by the fluid and solvent manufacturer.

DGloves.

DHearing protection.

309662 5

Component Description

Flow and Air Control

Fig. 1. The flow control (A) has a shut off and pressure

relief feature to soft start each time the gun is trig-

gered, instead of a blast of unatomized material. The

flow control has three modes:

DLOW/MED/HIGH: Triggering the gun sends an air

signal to the flow control that closes the prime valve

and starts the pump which fills the material hose.

When the gun trigger is released, the prime valve

opens and relieves the system pressure into the

supply container. When the gun is triggered the

automatic pressure relief, special TexSpray hoses

and pump design eliminate blasts of material and

spray pulsing to ensure consistent atomization.

DOFF: Puts the sprayer in neutral/relieve pressure --

neither the pump nor the gun will operate and there

is no material pressure in the pump, hose or gun.

DPRIME: The prime valve remains open so material

circulates through the pump and back to the supply

container through the drain hose.

The air control (B) increases or decreases the air

pressure to the sprayer from the air supply.

Fig. 1

OFF

PRIME

LOW/MED/HIGH

AB C

TI3101b

158

Blue

159

Black

Prime Valve

Fig. 1. The prime valve (C) relieves system pressure

and stops the pump when the gun trigger is released.

TexSpray Gun, 235490

EQUIPMENT MISUSE HAZARD

The TexSpray Gun 235490 is for use

only with the GM 1030 TexSpray 234113

which is designed so the fluid pressure

of the gun will not exceed the working pressure

rating of the components. The maximum fluid work-

ing pressure of the GM 1030 TexSpray is 750 psi

(5.1 MPa, 51 bar), but the recommended maximum

is 500 psi (3.4 MPa, 34 bar).

WARNING

INSTRUCTIONS

Fig. 2. Air flow is controlled at the gun. During priming,

turn the gun air control valve (D) in fully to prevent air

from mixing with the fluid, which allows you to check

and adjust the fluid flow accurately. (When this valve is

closed the air exits the rear of the gun.) During opera-

tion, open the air control valve to introduce air at the

correct volume for the desired spray pattern. The gun

also has a trigger bail (E) to reduce operator fatigue

when spraying large surfaces.

01808

Fig. 2 E

TexSpray Hoses

CAUTION

Use Graco hoses designed for this sprayer. Using

other hoses will damage the flow control.

6 309662

Component Description

Compressor Requirements

NOTE: This sprayer requires an external air compres-

sor.

UTION

Install an air filter on external air compressor to

reduce contamination to spray system.

Air compressor range: 10 scfm to 35 scfm, 30 to 140

psi (0.2--0.97 MPa, 2 to 9.7 bar)

Material Air Requirements* Minimum

Compressor

Size*

Elastomerics

(textured)

30 scfm at 90 psi

(0.84 m3/min at

0.63 MPa, 6.3 bar)

15 HP

Simulated

Accoustical

20 scfm at 60 psi

(0.56 m3/min at

0.42 MPa, 4.2 bar)

5.5 HP

Splatter Coat

and

Knockdown

15 scfm at 40 psi

(0.42 m3/min at

0.28 MPa, 2.8 bar)

8HP

Orange Peel 20 scfm at 60 psi

(0.56 m3/min at

0.42 MPa, 4.2 bar)

8HP

* Material, temperature and volume affect cfm needed

to properly atomize material.

Maintenance

UTION

DFor detailed engine maintenance and specifica-

tions, refer to separate HONDA engine manual.

DClose black fuel shutoff lever whenever you are

transporting sprayer to prevent fuel from flooding

engine.

DKeep sprayer upright and level when operating it

and when transporting it. This prevents crankcase

oil from leaking into combustion chamber, which

makes startup very difficult.

Daily: Check engine oil level and fill as needed.

Daily: Check and fill gas tank.

Daily: Check sprayer air filter, clean and replace

element as needed.

After first 20 hours of operation and each 100

hours thereafter: Change oil.

Weekly: Remove engine air filter cover and clean

element. In very dusty environments, check filter daily.

Replace element as needed. Replacement elements

can be purchased from your local HONDA dealer.

Spark plug: Use only a (NGK) BP6ES or BPR6ES

plug. Gap plug to 0.025 to 0.030 in. (0.7 to 0.8 mm).

Always use a spark plug wrench.

6 months: Clean Air Flow Sensor as follows:

1. Fig. 3. Loosen adapter (A). Pull down quick re-

lease (C) and swing out flow sensor regulator.

Disconnect connector (B).

2. Remove inlet fitting (D), retainer ring (E), piston (F)

and spring (G) from flow sensor regulator (H).

UTION

Do not scratch or nick piston (F) or inside of flow

sensor regulator (H).

3. Clean all parts (D, E, F, G). Clean inside of (H)

with a pipe cleaner.

4. Assemble all parts and install flow sensor regula-

tor.

Flow

Sensor Regulator

ti4366a

Flow

Sensor Regulator

D E FG H

Fig. 3

309662 7

Troubleshooting

To reduce risk of injury due to sprayer starting

unexpectedly, shut off engine before performing

checks or service.

WARNING

Check everything in chart before disassembling sprayer.

PROBLEM CAUSE SOLUTION

Engine does not start Engine switch not ON Turn engine switch ON

Outofgas Fill gas tank

Spark plug cable disconnected or

spark plug damaged

Connect spark plug cable or replace

spark plug

Oil seepage into combustion

chamber

Remove spark plug. Pull starter rope 3 or

4 times. Clean and install spark plug. Try

to start. Keep sprayer upright and do not

overfill engine crankcase to avoid oil

seepage.

Oil level low Add oil to engine crankcase

Engine operates, but

displacement pump does not

Flow control set to OFF Set flow control to PRIME mode or LOW/

MED/HIGH while triggering gun

Air compressor not on or insufficient

air flow from compressor

Start air compressor

Increase SCFM or compressor size.

Check air passages and tips for obstruc-

tions.

Check air filter element for clogs.

Air pressure set to low Check display for air pressure. System

requires a minimum of 40 psi (0.28 MPa,

2.8 bar) to operate. Increase pressure by

adjusting air control knob.

Sprayer engine RPM too low Increase engine speed

Clutch connector into back of circuit

board is loose.

Check and ensure a tight connection.

Air filter dirty Clean or replace filter element.

Air flow sensor dirty or damaged Check air filter.

Clean air flow sensor (see page 4) or re-

place as needed.

Air transducer failed Check display for correct air pressure

reading. Replace circuit board as need-

ed.

Fluid transducer failed Check connection at circuit board.

Replace fluid transducer.

Clutch not engaging Worn or damaged clutch. See page 18.

Fluid transducer failure. Air transducer

failure.

Displacement pump rod seized by

dry coating

Service pump. See page 10.

8 309662

Troubleshooting (Continued)

PROBLEM CAUSE SOLUTION

Engine operates, but

Connecting rod worn or damaged Replace connecting rod. See page 14.

acement pump

oes not

(

Continued

)

Drive housing worn or damaged Replace drive housing. See page 15.

(

)

Pinion assembly worn or damaged Service pinion assembly. See page 16.

Engine operates, displace-

ment pump operates, but no

Flow control is set to PRIME Set flow control to LOW/MED/HIGH while

triggering gun.

mater

pressure at gun. Fluid system over--pressurized Spraying material is too thick or the mate-

rial hose is too long. Use a less course

material or a shorter hose.

Gun nozzle/disk is clogged Check and clean nozzle/disk as needed.

Switch to a larger nozzle/disk.

Material flowing out drain line Check for air leaks to dump valve.

Check dump valve for wear, replace as

needed.

Air flow sensor dirty or damaged.

Pump is packed out Disassemble and clean pump (see page

8), hose(s) and gun.

Low fluid delivery Siphon hose strainer is clogged. Clean or remove strainer

Engine RPM too low Increase engine speed. See Startup,

procedure in operator manual.

Flow control set too low Increase flow control to MED or HIGH

Hose too long or material too

coarse

Change to a shorter hose or less coarse

material.

Material flowing out drain line Check drain line for a constant flow of

material when sprayer is operating in

LOW/MED/HIGH mode.

Check for air leaks to prime valve.

Check dump valve for wear, replace as

needed.

Gun nozzle/disk is clogged Check and clean nozzle/disk as needed.

Switch to a larger nozzle/disk.

Pump is packed out Disassemble and clean pump (see page

8), hose(s) and gun.

Loss of air control or volume

at gun

Gun air passages clogged with

material

After releasing gun trigger, make sure

system is fully depressurized before trig-

gering gun again. This helps prevent

material backing into gun passages.

Air filter dirty Clean or replace element

Air flow sensor dirty or damaged Check air filter.

Clean air flow sensor (see page 4) or re-

place as needed.

Displacement pump output

Piston ball (220) not seating Clean piston area. See page 12.

ow on upstro

ePiston packings worn or damaged Replace packings. See page 12.

Siphon hose coupling gasket (1e)

worn or missing.

Replace or install gasket

Pump cylinder o-ring (205) worn or

missing

Replace o-ring

309662 9

Troubleshooting (Continued)

PROBLEM CAUSE SOLUTION

Displacement pump output

Siphon hose strainer is clogged Clean strainer

ow on

ownstro

eor

strokes Piston packings worn or damaged Replace packings. See page 12.

Material leaks into wet-cup Intake valve ball (216) not seating

properly

Clean and service intake valve. See

page 12.

Clutch (9) worn or damaged Replace clutch. See page 18.

Air leak at pump foot valve or

siphon tube elbow

Be sure foot valve is tight each day.

Be sure seal in elbow is in place and is

not worn or damaged.

Material leaks into wet-cup Loose wet-cup (202) Tighten wet-cup enough to stop leakage

Throat packings worn or damaged Replace packings. See page 12.

Displacement rod (201) worn or

damaged

Replace displacement rod. See page 12.

Intermittent material flow out

of gun

Material supply is low or empty Refill and prime pump. See Startup proce-

dure in operator manual. Check material

supply often to prevent running pump dry.

Air control on gun is set too high. Reduce the air flow through the gun by

turning the air control knob on the back of

the gun.

Hose too long or material too

coarse

Change to a shorter hose or less coarse

material.

Heavy or poorly atomized mate-

rial when gun is first triggered

(lack of soft start)

Fluid pressure was not allowed to

fully self relieve after releasing gun

trigger

Wait longer between releasing gun trigger

and re--triggering.

(

)

Gun was not fully triggered immedi-

ately when squeezed, causing gun

air passages to clog with material.

Always squeeze trigger fully to prevent

just air from turning on, which starts pump

and pressurizes hoses. Disassemble and

clean gun.

Air valve failure Check and replace as needed

Air flow sensor dirty or damaged Check air filter.

Clean air flow sensor (see page 4) or re-

place as needed.

Pump does not shut off after

gun trigger is released

Air leaks in the system after the air

flow sensor

Check and tighten all connections be-

tween the air flow sensor and the gun.

Air leaks in gun Check gun for excessive air leaks and re-

pair.

See manual 309661

Air flow sensor dirty or damaged Check air filter.

Clean air flow sensor (see page 4) or re-

place as needed.

Premature prime valve fail-

ures

Pump does not shut off after gun

trigger is released.

Read “Pump does not shut off after gun

trigger is released” and fix appropriate

problem.

Repair or replace Prime Valve.

See page 19.

10 309662

Displacement Pump Repair

Removal

To reduce risk of injury due to sprayer starting

unexpectedly, shut off engine before performing

checks or service.

WARNING

1. Fig. 4. Flush sprayer. Remove suction hose elbow

(150a), pump outlet hose (A) and drain hose (64).

Fig. 4

ti12869a

150a

159

158

MOVING PARTS HAZARD

To reduce risk of amputating fingers,

keep fingers away from connecting rod

and pin while jogging engine.

WARNING

0407

Torque to 20 ft--lb (27 N.m)

Fig. 5

128

201

128

Back of pump

Cutaway view shows how pin (38) goes

through connecting rod

2. Fig. 5. Start engine. Jog flow control between

PRIME and OFF until connecting rod stops near

bottom of stroke. Shut off engine.

3. Loosen two quick disconnect screws (27).

4. Pry retaining spring (37) up on connecting

rod (128). Push pin (38) out with a screwdriver.

5. Fig. 6. Remove cover (C) to control housing (54)

by removing four screws (12). Detach pressure

transducer cord (63, Fig. 4) from control board (9)

at port (D). Remove pressure transducer cord from

control box.

6. Fig. 4. Remove air hoses (158) and (159) from

prime valve manifold (85). Note correct air hose

connection to ports on air cylinder (22). Use 5/16

inch wrench to hold ring on hose fitting while

removing hose from fitting.

7. Support weight of pump (3) and remove two quick

disconnect screws (27).

8. Unscrew assembled dump valve manifold (85) and

air cylinder (22) from pump (3).

Fig. 6

ti3007b

Repair

See page 12 for pump repair instructions.

This manual suits for next models

Table of contents

Other Graco Paint Sprayer manuals

Graco

Graco SENATOR 237-289 Operation manual

Graco

Graco 510 Manual

Graco

Graco 310778N Operating instructions

Graco

Graco Ultra Max II 695 Instruction Manual

Graco

Graco 700N User manual

Graco

Graco Reactor E-10hp User manual

Graco

Graco 245924 User manual

Graco

Graco magnum pro plus a20 Operating instructions

Graco

Graco XTR A Series User manual

Graco

Graco Ultra Guide

Graco

Graco HydraSprayr 230975 User manual

Graco

Graco Ultimate NOVA 395 PC Guide

Graco

Graco SP Operating instructions

Graco

Graco GX series Guide

Graco

Graco Wall Mount Series Datasheet

Graco

Graco Idler 257817 User manual

Graco

Graco Finex 24C308 User manual

Graco

Graco Delta Spray 237409 Operation manual

Graco

Graco Series B Operation manual

Graco

Graco HydraMax-225 233640 User manual

Graco

Graco DURON Performance 395 A Series Operation manual

Graco

Graco 231-547 Operation manual

Graco

Graco 237-421 Operation manual

Graco

Graco 190ES 261825 Operating instructions

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual