Graco Idler 257817 User manual

313900A

Repair Kit

Idler Repair Kit 257817

- For servicing FinishPro 290 Sprayers -

Pressure Relief Procedure

Important Safety Instructions

For detailed instructions and warnings,

see sprayer manual.

To reduce the risk of injury from injection, always follow

this procedure when instructed to relieve pressure,

stop spraying, service equipment, or install or clean

spray tip.

1. Set power/function selection switch to OFF and

unplug sprayer.

2. Turn pressure knob to lowest setting.

3. Hold gun to side of grounded metal pail. Trigger the

gun to relieve pressure.

4. Turn prime valve to PRIME.

If you suspect spray tip or hose is completely clogged, or

that pressure has not been fully relieved after following

these steps, VERY SLOWLY loosen tip guard retaining

nut or hose end coupling to relieve pressure gradually,

then loosen completely. Clear tip or hose obstruction.

ti9346a

ti14351a

2313900A

Disassembly

1. Relieve Pressure (see cover) and unplug sprayer.

2. Loosen IEC cord clamp screw and remove IEC plug

from compressor.

3. Remove air hose from compressor and remove out-

let fitting from compressor.

4. Remove four screws. Tip compressor assembly

down and forward to remove from sprayer. Place

compressor on workbench.

5. Remove two screws and IEC cord clamp. Remove

two screws and compressor shroud.

6. Remove three screws and belt cover.

7. Remove top and bottom idler pulley bracket screws

and remove idler assembly.

8. Remove three screws and motor belt guide plate.

9. Remove belt from pulleys.

ti13409a

ti13411a

ti13416a

Belt Cover

ti13414a ti13664a

ti13413a

ti14352a

ti13407a

313900A 3

Reassembly

1. Install new belt and guide plate with three screws.

2. Install idler assembly with two screws and washer

as shown. Do not fully tighten screws.

3. Place torque wrench in square hole and torque to

60 in-lb to properly tension belt. Tighten top and bot-

tom idler screws.

4. Torque top and bottom idler screws to 120 in-lb.

5. Install belt cover with three screws.

6. Install compressor shroud with two screws. Install

IEC cord clamp with two screws.

7. Install compressor outlet fitting.

8. Tip compressor assembly up and back into frame.

Install four screws.

9. Install IEC connector and tighten cord clamp. Install

air hose to outlet fitting. Make sure cord is pushed in

as far as it can go to ensure a good connection and

the screw is tightened securely.

ti13443a

ti14352a

ti13417a

ti13418a ti13419a

ti13413a

ti13414a ti13664a

ti13411a

ti13442a

ti13420a

4313900A

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

This manual contains English. MM 313900

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

www.graco.com

Other Graco Paint Sprayer manuals

Graco

Graco True Airless LTS15 Instruction Manual

Graco

Graco Series A Guide

Graco

Graco 24S134 Guide

Graco

Graco DURON Performance 395 A Series Operation manual

Graco

Graco 310548G Operating instructions

Graco

Graco GH 311279D User manual

Graco

Graco 207947 Operation manual

Graco

Graco SG3 Series User manual

Graco

Graco PRO Xs User manual

Graco

Graco e-Xtreme Z25 Use and care manual

Graco

Graco Triton 308 Operation manual

Graco

Graco HVLP EDGE II/EDGE II Plus Gun Use and care manual

Graco

Graco King 96A388 User manual

Graco

Graco TrueCoat Plus II 24N812 User manual

Graco

Graco Ultra-lite 235627 Datasheet

Graco

Graco Project Series User manual

Graco

Graco Fusion 2004230905 User manual

Graco

Graco 231 824 Operation manual

Graco

Graco XHF Parts list manual

Graco

Graco Magnum LTS 15 Operating instructions

Graco

Graco 3A0149C Datasheet

Graco

Graco 980 User manual

Graco

Graco 805-074 Series A User manual

Graco

Graco 233670 Operation manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual