GeoVision GV-BX2802 User manual
GV-BX2802, BX4802
Quick Start Guide
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual forfuture use. TVTBX-QG-A
© 2022 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
August 2022
Scan the following QR codes for product warranty and technical support
policy:
[Warranty] [Technical Support Policy]
i
Warning and Caution
⚫If the product does not work properly, please contact your dealer or the nearest service
center. Never attempt to disassemble the camera yourself. (We shall not be responsible
for any problems caused by unauthorized repair or maintenance.)
⚫Keep away from liquid while in use.
⚫In the use of the product, you must be strict compliance with the electrical safety
regulations of the nation and region. When the product is mounted on wall, the device
shall be firmly fixed.
⚫Do not use camera beyond specified voltage range.
⚫Do not drop the camera or subject it to physical shock.
⚫Avoid touching the camera lens.
⚫If cleaning is necessary, please use clean cloth to wipe it gently.
⚫Do not aim the camera at the sun or extra bright place.
⚫Do not place the camera in extremely hot, cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
⚫To avoid heat accumulation, good ventilation is required for operating environment.
ii
Contents
1. Overview..............................................................................................................1
2. Installation...........................................................................................................3
3. Accessing the Network Camera ........................................................................4
3.1 Looking Up the Dynamic IP Address.............................................................4
3.2 Configuring the IP Address ............................................................................6
4. The Web Interface...............................................................................................7
5. Upgrading System Firmware .............................................................................8
6. Restoring to Factory Default..............................................................................9
1
1. Overview
1
Power port (DC 12V / AC 24V)
7
Ethernet connector (PoE)
2
Power indicator
8
Micro SD card slot
3
RS-485; connectors for PTZ
9
Audio input
4
Alarm output
10
Audio output
5
Alarm input
11
Default button
6
Ground
12
Video output
Note:
1. The camera can be powered by DC 12V / PoE power supply. If the PoE switch is used
to power the camera, DC 12V power supply is not required.
2. To load default settings, press and hold the default button for 10 seconds.
2
3
2. Installation
Please make sure that the wall or ceiling is strong enough to withstand 3 times the
weight of the camera. Install the camera under dry environment. Here we take
1. Insert a micro SD card into the card slot.
2. Remove the protection cover of the lens interface and install the lens (not supplied)
to the camera. Rotate the lens clockwise until it is fixed firmly. Plug the cable of auto
iris to the auto iris interface of the camera.
Note: It is not required to plug the power cable of the auto iris to the auto iris interface if a
manual iris lens is used.
4
3. Accessing the Network Camera
3.1 Looking Up the Dynamic IP Address
By default, when the camera is connected to a LAN with the DHCP server, it is
automatically assigned with a dynamic IP address. Follow the steps below to look up its IP
address.
Note:
1. By default, the Administrator’s username is admin and cannot be modified.
2. This function is only applicable on GV-IP Device Utility V8.9.8 or later.
1. Make sure the PC used to configure the IP address is under the same LAN as the camera.
Download and install GV-IP Device Utility from the company website.
2. On the GV-IP Utility window, click the button to search for the IP devices connected in
the same LAN. Click the Name or Mac Address column to sort.
3. Find the camera with its Mac Address, and click on its IP address.
4. For the first-time users, you are requested to set up a password.
5
5. Type a new password and click OK.
6. Click on its IP address again and select Webpage to open its Web interface.
7. Type the set password on the login page and click Login.
IMPORTANT:
1. The camera has two sets of passwords: one is for Web interface and the other is
for the third-party platform connection via ONVIF, e.g. GV-VMS.GV-IP Device Utility
is used to set the ONVIF password. When the first-time user uses GV-IP Device Utility
to set a password for the camera, the two sets of passwords are created simultaneously.
2. To change the password for Web interface, click Config →Security →User ; see
“Modify User”in 4.7.1 Security Configuration in the user’s manual. To change the
password for ONVIF connection, click Config →Network →Advnaced; see 4.6.4
ONVIF in the user’s manual.
3. If the first-time user accesses the camera’s Web interface on the browser directly by
using the IP address found in GV-IP Device Utility, the following dialog box will apear.
If “Activate Onvif User”is enabled, the ONVIF user can be activated simultanously for the
third-party platform connection via ONVIF, using the default username and set password set
above to connect.
6
3.2 Configuring the IP Address
If the camera is connected to a LAN without the DHCP server, the default IP address will be
192.168.0.10. Follow the steps below to modify the IP address to avoid IP conflict with other
GV-IP devices on the same LAN.
1. Open your Web browser, and type the default IP address 192.168.0.10.
2. Type the default username admin and a password. Click Login.
3. Go to Config > Network > TCP/IP to set the IP address.
4. Select Use the following IP address and then enter the static IP address and other
parameters.
Other manuals for GV-BX2802
1
This manual suits for next models
1
Table of contents
Other GeoVision Security Camera manuals
GeoVision
GeoVision GV-SD200 User manual
GeoVision
GeoVision GV-IPCamera Series User manual
GeoVision
GeoVision GV-IPCam H.264 Series User manual
GeoVision
GeoVision GV-MFD1501 User manual
GeoVision
GeoVision GV-LPR CAM 10A User manual
GeoVision
GeoVision GV-EDR2700 Series User manual
GeoVision
GeoVision GV-3D People Counter V2 User manual
GeoVision
GeoVision 84-SD2301S-2011 User manual
GeoVision
GeoVision GV-EBD4700 User manual
GeoVision
GeoVision GV-BL5311 Use and care manual
GeoVision
GeoVision GV-LPR2800-DL User manual
GeoVision
GeoVision 90-BX2700F-8010 User manual
GeoVision
GeoVision GV-IP User manual
GeoVision
GeoVision GV-BX110D User manual
GeoVision
GeoVision GV-OPAL S1 User manual
GeoVision
GeoVision GV-VD8700 User manual
GeoVision
GeoVision GV-IP Speed User manual
GeoVision
GeoVision GV-EBD2702: GV-EBD4700 User manual
GeoVision
GeoVision GV-FER12700 User manual
GeoVision
GeoVision GV-PFER12800 User manual
