G2glighting Talent II Series User manual
Talent I l Series
Tallent Il Instruction
SPECIFICATIONS
Model
Colors
Control points
Output port
Gray scale
Input Voltage
Rated Power
SD Card
Size
Interface
Tallent II
RGB three primary colors、RGBW four primary color、full-color display
Control 1024 pixels each port(DMX is 512 pixels)
Synchronous serial shift signal×2,compatible DMX512 signal×2
256 class—65536 class
AC 12V/ DC 7.5V-24V/ DC 5V
2W
4GB
190.0mm×96.3mm×32.5mm
3Pin interface×5 4Pin interface×2
190MM
174.8MM
84.3MM
96.3MM
MENU
Play and Pause
Set Menu
Self Test
Exit Setup
Numeric Key
Confirm and save
Plus
Minus
Previous fragment
Next fragment
OK
Add key
Key reduction
MENU
TEST
OK
OKMU
MU
190MM
0
+
-
1 2 3
4 5 6
7 8 9
C
www.g2glighting.com155A10t hStPassai c,NJ07055Phone:(973)575-2600Fax:(973)575- 2603
Setup controller parameters with buttons,such as driver chip type、controller numbere、
The controller output have 2 SPI signal output port and 2 DMX512 signal output port.
Integration of multiple driving chip,change the IC type、clock frequency、duty cycle、
Support environmental lighting control and audio control sensor module (optional) application,
Supports most serial driver LED driver chip.
Tallent II Size
Tallent Front View
Tallent Rear View
Tallent II Button control panel
Tallent II Remote control button definition
31MM
160MM
32.5MM
AC12V
Power input
DMX512
signal output
serial signal
output
remote control
receiver
DC Power
Supply
Synchronous
signal input
Synchronous
signal output
programs、playing speed、brightness of lamps;
grayscale by softword setting.
adjust the brightness of lamps interactively.
Press ,enter the ID setting in menu ,as shown below
Press again ,enter the playback speed selection interface,as shown below:
Press again to enter date and time setting interface. As figure below
Press adjust related value,Press to save.
Attention:in this interface,press switch to frame rate,press to select its value.
Press ,enter the play mode selection interface,as shown below:
Press ,Setting the number,Press to save this option。
Attention:The ID number should be less than the quantity of controller in your layout file.
Press ,select Loop mode、Wait mode and fragment Loop play mode ,Press to save the option.
Press ,setting the rate value,press to save.
Talent I l Series
Controller keys and display instructions
一、LCD main screen after boot
二、Controller parameters setting
1、Controller Number
2、Play mode
3、Playback speed
4、Date and time setting interface
5、Brightness adjustment
ress
Press again to enter brightness adjustment settings inter face. As figure below:
Controller name
No SD Card State
MR- 502
NO CARD
play mode
Loop mode
INDEX
=Loop
Playback speed
frame rate
SPEED=25
FPS=X01
year
Month - Day
2015
-05－18
Time
Hour-Minute-Second
Time
19:30:00
play mode
fragment Loop play mode
INDEX
=01
play mode
wait mode
INDEX
=Wait
controller number
ID=001
Controller name
ID=001
PLAY 001
Controller name
No files in SD Card
MR- 502
NO Files
Currently playing program fragment number
Press ,set brightness,Press to save
Press again to enter Brightness of the four channels adjustment settings interface. As figure below:
6、Brightness of the four channels Adjustment
7、synchronization mode
8、Setting driver chip type
Press again,to enter synchronization mode settings interface. As figure below:
Press again,to enter driver chip type settings interface. As figure below:
Press to set brightness,press to save.
Press to set synchronization mode,press to save.
Press to select your own driver chip type ,press to save.
Talent II Series
www.g2glighting.com155A10t hStPassai c,NJ07055Phone:(973)575- 2600Fax:(973)575- 2603
Brightness
Brightness percentage
BRIGHT
=100%
A channel brightness
Brightness Percentage
COLOR A
=100%
B channel brightness
Brightness Percentage
COLOR B
=100%
C channel brightness
Brightness Percentage
COLOR C
=100%
D channel brightness
Brightness Percentage
COLOR D
=100%
synchronization mode
GPS satellite
SYNC=
GPS
synchronization mode
Close GPS synchronization
SYNC=
NO
driver chip type
Select your driver chip
Chip Sel=
NO Chip
9、Remote control adjustment
Press again,to enter Remote control settings interface. As figure below:
Press to select your own driver chip type ,press to save.
Remote control mode
serial port control
REMOTE=
UART
Remote control mode
SIM communication mode
REMOTE=
SIM
Remote control mode
Shut up remote control
REMOTE=
OFF
Remote control mode
WIFI communication
REMOTE=
WIFI
10、DMX512 chip address
Press again,to enter DMX512 chip address settings interface. As figure below:
Press to switch S and T cursor position,press to change the value,press to save
Chip Type
start channel
MR-DMX05=
ST=001
Chip Type
DMX512AP=
SOO1 T03
Chip Type
TM512=
SOO1 T03
Chip Type
S represent start channel
T represent channel quantity of lamp
UCS512=
SOO1 T03
synchronization
S represent start channel
T represent channel quantity of lamp
S represent start channel
T represent channel quantity of lamp
Press to enter controller number settings interface. As figure below:
Press to set controller number ,press to save.
when playing a segment,press adjust the playback of fragment
On playing mode,Press to stop. As figure below:
grating test
On the working state ,Press again to enter self test setting interface. As figure below:
OK
三、Remote control operation during playing
11、Self Test Setting
12、Pause
1、Controller Number
press again to back to controller play state.
Talent Il Series
www.g2glighting.com155A10t hStPassai c,NJ07055Phone:(973)575- 2600Fax:(973)575- 2603
Self Test
-TEST-
LINE0018
Self Test
Red Self Test
-TEST-
2 RED
Self Test
Green Self Test
-TEST-
3 GREEN
Self Test
Blue Self Test
-TEST-
4 BLUE
Self Test
Blue Self Test
-TEST-
5 WHITE
Self Test
Ching Self Test
-TEST-
6 CHING
Self Test
Yellow Self Test
-TEST-
7 YELLOW
Self Test
Pupple Self Test
-TEST-
8 PURPLE
Self Test
Trip of red, green, blue and white
-TEST-
9 RGBW
Self Test
Colorful gradient
-TEST-
10 COLOR
On playing mode ,Press to pause. As figure below:
Press again , play again
Controller Type
Pause
MR-502
PAUSE
13、Stop playing
Press back to play.
Controller Type
stop
Controller number
Currently playing program fragment number
MR-502
PLAY OFF
14、Adjust program segment
ID=001
PLAY 001
Play mode
Loop mode
ID=001
Attention:The ID number should be less than the quantity of controller in your layout file.
Press to set synchronization mode,press to save.
Press again to enter Brightness of the four channels adjustment settings interface. As figure below:
Press to set brightness,press to save.
Press ,set brightness,Press to save
Press ,select Loop mode、Wait mode and fragment Loop play mode ,Press to save the option.
Press ,setting the rate value,press to save.
5、Brightness adjustment
Press again to enter brightness adjustment settings inter face. As figure below:
Press again ,enter the playback speed selection interface,as shown below:
Attention:in this interface,press switch to frame rate,press to select its value.
Playback speed
frame rate
SPEED=25
FPS=X01
Press again to enter date and time setting interface. As figure below
Press adjust related value,Press to save.
year
Month- Day
2015
-05－18
Time
Hour-Minute-Second
Time
19:30:00
Talent Il Series
www.g2glighting.com155A10t hStPassai c,NJ07055Phone:(973)575- 2600Fax:(973)575- 2603
MU
MU
MU
MU
MU
MU
MU
Brightness
Brightness percentage
BRIGHT
=100%
6、Brightness of the four channels Adjustment
A channel brightness
Brightness Percentage
COLOR A
=100%
B channel brightness
Brightness Percentage
COLOR B
=100%
C channel brightness
Brightness Percentage
COLOR C
=100%
D channel brightness
Brightness Percentage
COLOR D
=100%
Press ,enter the play mode selection interface,as shown below:
OK
OK
OK
OK
OK
OK
OK
2、Play mode
3、Playback speed
4、Date and time setting interface
play mode
Loop mode
INDEX
=Loop
play mode
fragment Loop play mode
INDEX
=01
play mode
Wait mode
INDEX
=Wait
7、synchronization mode
Press again,to enter synchronization mode settings interface. As figure below:
synchronization mode
GPS satellite
SYNC=
GPS
synchronization mode
Close GPS synchronization
SYNC=
NO
synchronization
Press again,to enter DMX512 chip address settings interface. As figure below:
Press to switch S and T cursor position,press to change the value,press to save
Press to select your own driver chip type ,press to save.
Press again,to enter Remote control settings interface. As figure below:
Press to select your own driver chip type ,press to save.
Press again,to enter driver chip type settings interface. As figure below:
MU
MU
MU
MU
Talent Il Series
www.g2glighting.com155A10t hStPassai c,NJ07055Phone:(973)575- 2600Fax:(973)575- 2603
11、Pause
On playing mode ,Press to pause. As figure below:
Press back to play
Controller Type
Pause
MR-502
PAUSE
OK
OK
OK
OK
OK
8、Setting driver chip type
driver chip type
Select your driver chip
Chip Sel=
NO Chip
9、Remote control adjustment
Remote control mode
Uart Control
REMOTE=
UART
Remote control mode
SIM Communication mode
REMOTE=
SIM
Remote control mode
Close remote control
REMOTE=
OFF
Remote control mode
WIFI Communication
REMOTE=
WIFI
10、DMX512 chip address
Chip Type
start channel
MR-DMX05=
ST=001
Chip Type
DMX512AP=
SOO1 T03
Chip Type
TM512=
SOO1 T03
Chip Type
S represent start channel
T represent channel quantity of lamp
S represent start channel
T represent channel quantity of lamp
S represent start channel
T represent channel quantity of lamp
UCS512=
SOO1 T03
Other G2glighting Controllers manuals
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
