Fujitsu ETERNUS AX Series Instruction Manual
CA08871-050-01/6
FUJITSU Storage ETERNUS AX/HX Series
Installing a Cisco Nexus 9336C-FX2 switch and
pass-through panel in a Fujitsu cabinet
For Cisco Nexus 9336C-FX2 switches
|Contents|
Contents
Installing a Cisco Nexus 9336C-FX2 switch and pass-through panel in a
Fujitsu cabinet.............................................................................................3
Copyright and trademark....................................................................................................7
Copyright................................................................................................................................................ 7
Trademark...............................................................................................................................................7
How to send comments about documentation and receive update notifications.............8
ii
Installing a Cisco Nexus 9336C-FX2 switch and pass-through
panel in a Fujitsu cabinet
You can install the Cisco Nexus 9336C-FX2 switch and pass-through panel in a Fujitsu cabinet with the
standard brackets that are included with the switch.
Before you begin
You must have reviewed the initial preparation requirements, kit contents, and safety precautions.
Cisco Nexus 9000 Series Hardware Installation Guide
About this task
• For each switch, you must supply the eight 10-32 or 12-24 screws and clip nuts to mount the brackets and
slider rails to the front and rear cabinet posts.
• You must use the Cisco standard rail kit to install the switch in a Fujitsu cabinet.
Note: The jumper cords are not included with the pass-through kit and should be included with your switches.
Procedure
1. Install the pass-through blanking panel in the Fujitsu cabinet.
The Fujitsu pass-through panel kit contains the following hardware:
• One pass-through blanking panel
• Four 10-32 x .75 screws
• Four 10-32 clip nuts
a) Determine the vertical location of the switches and blanking panel in the cabinet.
In this procedure, the blanking panel will be installed in U40.
b) Install two clip nuts on each side in the appropriate square holes for front cabinet rails.
c) Center the panel vertically to prevent intrusion into adjacent rack space, and then tighten the screws.
d) Insert the female connectors of both 48-inch jumper cords from the rear of the panel and through the
brush assembly.
1. Female connector of the jumper cord.
2. Install the rack-mount brackets on the Nexus 9336C-FX2 switch chassis.
a) Position a front rack-mount bracket on one side of the switch chassis so that the mounting ear is
aligned with the chassis faceplate (on the PSU or fan side), and then use four M4 screws to attach the
bracket to the chassis.
3
|Installing a Cisco Nexus 9336C-FX2 switch and pass-through panel in a Fujitsu cabinet|
b) Repeat step 2a with the other front rack-mount bracket on the other side of the switch.
c) Install the rear rack-mount bracket on the switch chassis.
d) Repeat step 2c with the other rear rack-mount bracket on the other side of the switch.
3. Install the clip nuts in the square hole locations for all four IEA posts.
The two 9336C-FX2 switches will always be mounted in the top 2U of the cabinet RU41 and 42.
4. Install the slider rails in the cabinet.
a) Position the first slider rail at the RU42 mark on the back side of the rear left post, insert screws with
the matching thread type, and then tighten the screws with your fingers.
4
|Installing a Cisco Nexus 9336C-FX2 switch and pass-through panel in a Fujitsu cabinet|
1. As you gently slide the slider rail, align it to the screw holes in the rack.
2. Tighten the screws of the slider rails to the cabinet posts.
b) Repeat step 4a for the right side rear post.
c) Repeat steps 4a and 4b at the RU41 locations on the cabinet.
5. Install the switch in the cabinet.
Attention: This step requires two people: one person to support the switch from the front and
another to guide the switch into the rear slider rails.
a) Position the back of the switch at RU41.
1. As the chassis is pushed toward the rear posts, align the two rear rack-mount guides with the slider
rails.
2. Gently slide the switch until the front rack-mount brackets are flush with the front posts.
b) Attach the switch to the cabinet.
5
|Installing a Cisco Nexus 9336C-FX2 switch and pass-through panel in a Fujitsu cabinet|
1. With one person holding the front of the chassis level, the other person should fully tighten the four
rear screws to the cabinet posts.
c) With the chassis now supported without assistance, fully tighten the front screws to the posts.
d) Repeat steps 5a through 5c for the second switch at the RU42 location.
Note: By using the fully installed switch as a support, it is not necessary to hold the front of the second
switch during the installation process.
6. When the switches are installed, connect the jumper cords to the switch power inlets.
7. Connect the male plugs of both jumper cords to the closest available PDU outlets.
Note: To maintain redundancy, the two cords must be connected to different PDUs.
8. Connect the management port on each 9336C-FX2 switch to either of the management switches (if
ordered) or connect them directly to your management network.
The management port is the upper-right port located on the PSU side of the switch. The CAT6 cable for
each switch needs to be routed through the pass-through panel after the switches are installed to connect
to the management switches or management network.
6
Copyright and trademark
Copyright
Copyright 2021 FUJITSU LIMITED. All rights reserved.
No part of this document covered by copyright may be reproduced in any form or by any means - graphic,
electronic, or mechanical, including photocopying, recording, taping, or storage in an electronic retrieval
system - without prior written permission of the copyright owner.
Software derived from copyrighted Fujitsu material is subject to the following license and disclaimer:
THIS SOFTWARE IS PROVIDED BY FUJITSU "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WHICH ARE HEREBY DISCLAIMED. IN NO EVENT SHALL FUJITSU BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Fujitsu reserves the right to change any products described herein at any time, and without notice. Fujitsu
assumes no responsibility or liability arising from the use of products described herein, except as expressly
agreed to in writing by Fujitsu. The use or purchase of this product does not convey a license under any patent
rights, trademark rights, or any other intellectual property rights of Fujitsu.
Trademark
FUJITSU, FUJITSU logo, and ETERNUS are trademarks of Fujitsu. All other trademarks are the property of their
respective owners.
https://www.fujitsu.com/global/products/computing/storage/eternus/trademarks.html
7
|How to send comments about documentation and receive update notifications|
How to send comments about documentation and receive
update notifications
The latest version of this document and the latest information related to this device are available at the
following site.
https://www.fujitsu.com/global/support/products/computing/storage/manuals-list.html
If necessary, refer to the manuals for your model.
8
FUJITSU Storage ETERNUS AX/HX Series
Installing a Cisco Nexus 9336C-FX2 switch and pass-through panel in a Fujitsu cabinet
For Cisco Nexus 9336C-FX2 switches
CA08871-050-01/6
Date of issuance: Nov 2021
Issuance responsibility: FUJITSU LIMITED
• The content of this manual is subject to change without notice.
• This manual was prepared with the utmost attention to detail.
However, Fujitsu shall assume no responsibility for any operational problems as the result of errors, omissions, or the
use of information in this manual.
• Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information
in this manual.
• The content of this manual may not be reproduced or distributed in part or in its entirety without prior permission from
Fujitsu.
Other manuals for ETERNUS AX Series
3
This manual suits for next models
1
Table of contents
Other Fujitsu Storage manuals
Fujitsu
Fujitsu DYNAMO 640AI User manual
Fujitsu
Fujitsu MPF3XXXAH User manual
Fujitsu
Fujitsu MHV2160BT User manual
Fujitsu
Fujitsu ETERNUS DX100 S4 Technical manual
Fujitsu
Fujitsu ETERNUS DX60 S2 User manual
Fujitsu
Fujitsu Citrix XenServer User manual
Fujitsu
Fujitsu GP5-HD9G4 User manual
Fujitsu
Fujitsu ETERNUS JX40 S2 User manual
Fujitsu
Fujitsu Eternus DX80 S2 Installation guide
Fujitsu
Fujitsu MPG3xxxAT User manual
Fujitsu
Fujitsu ETERNUS CS800 S6 User manual
Fujitsu
Fujitsu Eternus DX200F User manual
Fujitsu
Fujitsu PRIMERGY LTO3 User manual
Fujitsu
Fujitsu MBA3300FD User manual
Fujitsu
Fujitsu C141-E090-02EN User manual
Fujitsu
Fujitsu GRANPOWER500 TEAMSERVER Series User manual
Fujitsu
Fujitsu ETERNUS DX60 S3 User manual
Fujitsu
Fujitsu ETERNUS DX60 S2 User manual
Fujitsu
Fujitsu ETERNUS DX500 S4 User manual
Fujitsu
Fujitsu Eternus DX500 S3 User manual
