Frigidaire FFFW5100PW User manual

All about the

Installation

of your Washer

Important Safety Instructions..............................2-3

Installation Requirements ...................................4-6

Installation Instructions....................................7-10

Accessories.........................................................11

Notes.................................................................12

Français..............................................................13

Español ..............................................................25

TABLE OF CONTENTS

137621300A (1304)

IMPORTANT SAFETY INSTRUCTIONS

Shipping Hardware

Foam shipping support (under wash tub)

removed and stored

Shipping bolts and spacers removed from rear

of appliance and stored

Hole plugs (shipped in bag in drum) installed in

holes in backsheet

Leveling

Washer is level, side-to-side and front-to-back

Cabinet is setting solid on all corners

Water Supply

Use only new hoses and verify rubber sealing

washers are installed

HOT supply is connected to HOT inlet and

COLD supply is connected to COLD inlet

HOT and COLD water supply turned on

No leaks present at water supply connections

or appliance inlet connections -

recheck in 24 hours

Drain

Stand pipe or wall drain height minimum 24”

Anti-siphon disc (shipped in drum) installed on

drain hose

Drain hose secured in place with cable tie

(shipped in drum)

Electrical Power

 House power turned on

Washer plugged in

Final Checks



Installation Instructions

and

Use and Care

Guide

read thoroughly

Door locks and water enters drum when cycle

starts

Registration card sent in

Installation Checklist

Deﬁnitions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury

or death.

Recognize safety symbols, words

and labels

Safety items throughout this manual are labeled with

a WARNING or CAUTION based on the risk type as

described below:

IMPORTANT

IMPORTANT indicates installation, operation or

maintenance information which is important but not

hazard-related.

WARNING

WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

WARNING

Please read all instructions before using this washer.

CAUTION

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury.

DANGER

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury.

IMPORTANT SAFETY INSTRUCTIONS

NOTE

The electrical service to the washer must conform with

local codes and ordinances and the latest edition of the

National Electrical Code, ANSI/NFPA 70, or in Canada,

the Canadian Electrical Code C22.1 part 1.

NOTE

Hoses are not included with washer purchase. See

“Accessories” section for various inlet hose kits to ﬁt

your speciﬁc installation.

WARNING

FIRE HAZARD

For your safety the information in this manual must be

followed to minimize the risk of ﬁre or explosion or to

prevent property damage, personal injury or loss of life.

Do not store or use gasoline or other ﬂammable vapors

and liquids in the vicinity of this or any other appliance.

WARNING

SUFFOCATION HAZARD

Destroy the carton and plastic bags after the washer is

unpacked. Children might use them for play. Cartons

covered with rugs, bedspreads, or plastic sheets can

become airtight chambers causing suffocation. Place

all materials in a garbage container or make materials

inaccessible to children.

IMPORTANT

The instructions in this manual and all other literature

included with this washer are not meant to cover

every possible condition and situation that may occur.

Good safe practice and caution MUST be applied when

installing, operating and maintaining any appliance.

Maximum beneﬁts and enjoyment are achieved

when all the Safety and Operating Instructions are

understood and practiced as a routine with your

laundering tasks.

CAUTION

EXCESSIVE WEIGHT HAZARD

To avoid back or other injury, have more than one

person move or lift the washer.

Save these instructions for future reference.

Tools and materials needed for installation:

Adjustable

pliers

Adjustable

wrench

3/8” or 10 mm

box wrench

OR OR AND AND

Ratchet and

socket set

Carpenter’s level

Inlet hose (x2)

INSTALLATION REQUIREMENTS

NOTE

Drain hose attached to the washer can reach a 74 in.

(188 cm) high standpipe. For higher standpipe, use

hose P/N 137098000, available from an authorized

parts distributor.

NOTE

GFI (Ground Fault Interrupter) receptacle is not

required.

NOTE

Because of potentially inconsistent voltage capabilities,

the use of this washer with power created by gas

powered generators, solar powered generators, wind

powered generators or any other generator other than

the local utility company is not recommended.

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY - 2 wire, with ground, 120 volt single

phase, 60 Hz, Alternating Current.

OUTLET RECEPTACLE - Properly grounded 3-prong

receptacle to be located so the power supply cord is

accessible when the washer is in an installed position.

Grounding type

ll receptacl

ll receptacle

wer cord with

3-prong

ounded plug

Do not,

under

y cir

cumstances,

cut,

remo

ve,

or b

ypass th

ypass the

ounding pr

ong.

96”

(244cm)

max.

24”

(61cm)

min.

Drain system requirements

1Drain capable of eliminating 17 gals (64.3 L) per

minute.

2A standpipe diameter of 1-1/4 in. (3.18 cm)

minimum.

3The standpipe height above the ﬂoor should be:

Minimum height: 24 in. (61 cm)

Maximum height: 96 in. (244 cm)

Water supply requirements

Hot and cold water faucets MUST be installed within hose

length of your washer’s water inlet. The faucets MUST

be 3/4 inch (1.9 cm) with threading for laundry hose

connection. Water pressure MUST be between 30 and

120 psi. Pressure difference between hot and cold cannot

be more than 10 psi. Your water department can advise

you of your water pressure.

1The washer MUST be grounded. In the event of

malfunction or breakdown, grounding will reduce

the risk of electrical shock by a path of least

resistance for electrical current.

2Since your washer is equipped with a power supply

cord having an equipment-grounding conductor

and a grounding plug, the plug MUST be plugged

into an appropriate, copper wired receptacle that is

properly installed and grounded in accordance with

all local codes and ordinances or in the absence

of local codes, with the National Electrical Codes,

ANSI/NFPA 70 (latest edition). If in doubt, call a

licensed electrician. DO NOT cut off or alter the

grounding prong on the power supply cord. In

situations where a two-slot receptacle is present,

it is the owner’s responsibility to have a licensed

electrician replace it with a properly grounded three

prong grounding type receptacle.

Ground requirements

Electrical system requirements

WARNING

ELECTRICAL SHOCK HAZARD

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check

with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

INSTALLATION REQUIREMENTS

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Under-

Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm) 1” (2.5 cm)

0”

(0cm)

0”

(0cm)

1”

(2.5cm)

0”

(0cm)

Installation in a Recess or Closet

If washer and dryer are installed in the same closet,

door ventilation is required: A minimum of 120 square

inches (774.2 cm²) of opening, equally divided at the top

and bottom of the door, is required. Louvered openings

should be located 3 inches (7.6 cm) from bottom and

top of door. Air openings are required to be unobstructed

when a door is installed. A louvered door with equivalent

air openings for the full length of the door is acceptable.

60 sq. in.

(387.1cm²)

3”

(7.6cm)

60 sq. in.

(387.1cm²)

3”

(7.6cm)

closet door

Clearance requirements

IMPORTANT

DO NOT INSTALL YOUR WASHER:

1 In an area exposed to dripping water or outside

weather conditions. The ambient temperature

should never be below 60° F (15.6° C) to

maximize detergent effectiveness.

2 In an area (garage or garage-type building)

where gasoline or other ﬂammables (including

automobiles) are kept or stored.

3 On carpet. Floor MUST be solid with a maximum

slope of 1 inch (2.5 cm). To minimize vibration

or movement, reinforcement of the ﬂoor may be

necessary.

Washer Dimensions

*Connection of water inlet hose on steam dryer adds 3/4 in. (2 cm) to installation depth.

1Power supply cord length on washer approximately 60 inches (152.5 cm).

2Drain hose length on washer approximately 59 inches (150 cm).

3Power supply cord length on gas dryer approximately 60 inches (152.5 cm).

gas supply

pipe on rear

of gas unit

water supply

connection on

rear of unit

power cord

on rear of

unit1

ﬂoor line

71.5”

(182 cm)

37”

(94 cm)

39”

(99 cm)

27.0”

(68.5 cm)

electrical

supply on

rear of unit3

centerline

height for

rear vent

drain hose on

rear of unit2

30.3” (77 cm)*

to front of closed door

51.4” (131 cm)*

to clear open door

ﬂoor line

30.3” (77 cm)*

to front of closed door

freestand washer

on ﬂoor

washer mounted on

optional pedestal

51.4” (131 cm)*

to clear open door

36.0”

(91.5 cm)

51.25”

(130 cm)

power cord on

rear of unit1

drain hose on

rear of unit2

water supply

connection on

rear of unit

27.0”

(68.5 cm)

INSTALLATION REQUIREMENTS

1Temporarily remove door tape.

2Open washer door and remove everything from the

drum.

3Close door and reapply door tape.

4Using a rug, blanket or piece of cardboard to

protect the ﬂoor, carefully lay the washer on it’s

back.

Removing foam packaging

5Remove styrofoam base and shipping plug and set

them aside.

6Carefully return the washer to an upright position.

7Carefully move the washer to within 4 feet (1 m) of

its ﬁnal location.

WARNING

SUFFOCATION HAZARD

Destroy the carton and plastic bags after the washer is

unpacked. Children might use them for play. Cartons

covered with rugs, bedspreads, or plastic sheets can

become airtight chambers causing suffocation. Place

all materials in a garbage container or make materials

inaccessible to children.

CAUTION

EXCESSIVE WEIGHT HAZARD

To avoid back or other injury, have more than one

person move or lift the washer.

IMPORTANT

Save styrofoam base and shipping plug for use to help

prevent washer damage during any future moves.

INSTALLATION INSTRUCTIONS

x 4

4 HOLE PLUGS

(IN BAG)

Locate 4 hole plugs in the small bag supplied

with washer instruction guides. Insert them in

the holes in washer back panel.

Removing shipping hardware

Installing hole plugs

Remove all of the following:

4 SPACERS

4 BOLTS

2 P CLAMPS

x 4

x 2

x 4

4 SPACERS

4 BOLTS

2 P CLAMPS

IMPORTANT

Save all shipping bolts and spacers for future use. If

the washer is to be transported at a later date, the

shipping hardware must be reinstalled to help prevent

shipping damage.

NOTE

Rubber expansion material on spacers may need

time to relax before they can be easily pulled through

shipping hole.

INSTALLATION INSTRUCTIONS

raise lower

Leveling your washer

Excessive noise and vibration can be prevented by

properly leveling the washer.

1For free standing installation and with the washer

within 4 feet (1 m) of its ﬁnal location, place a level

on top of the washer.

2Use adjustable pliers to adjust the leveling legs so

the washer is level front-to-rear and side-to-side,

and stable corner-to-corner.

3Press down on alternate corners and sides and feel

for the slightest movement. Adjust the appropriate

leg(s) so the washer sits solidly on the ﬂoor on

ALL four legs. Keep the leveling leg extension at a

minimum for best performance of the washer.

Connecting inlet water

COLD

HOT

NOTE

For pedestal installations, see additional installation

instructions included with the pedestal.

NOTE

Hoses are not included with washer purchase. See

“Accessories” section for various inlet hose kits to ﬁt

your speciﬁc installation.

1Run some water from the hot and cold faucets

to ﬂush the water lines and remove particles

that might clog the water valve screens and to

determine which faucet is hot and which is cold

supply.

2Connect the HOT inlet hose to the HOT inlet

connection on the washer and the COLD inlet

hose to the COLD inlet connection on the washer.

Tighten by hand until snug. Then tighten each

supply connection another 2/3 turn with pliers.

Do not cross thread or over-tighten these

connections.

3Connect the HOT inlet hose to the HOT water

supply and the COLD inlet hose to the COLD water

supply. Tighten by hand until snug. Then tighten

each supply connection another 2/3 turn with

pliers. Do not bend, kink or pinch water inlet

hoses.

4Turn on the water and check for leaks.

RUBBER WASHERS

MUST BE PRESENT USE ONLY

NEW HOSES

INSTALLATION INSTRUCTIONS

CABLE TIE

ANTI-SIPHON

DISC

SLIDE DISC

TO HERE

Grounding type

ll receptacl

ll receptacle

wer cord with

3-prong

ounded plug

Do not,

under

y cir

cumstances,

cut,

remo

ve,

or b

ypass th

ypass the

ounding pr

ong.

Connecting drain and electrical

1Locate the anti-siphon ring shipped with your

washer. Place it over the end of the drain hose and

slide it past the ﬁrst ring of “accordion” ribs.

2Form a “U” shape on the end of the drain hose

with the hose pointed toward the drain. Place the

formed end in a laundry tub or a standpipe and

secure the drain hose with the cable tie (provided

in the enclosure package) to the standpipe, inlet

hose, laundry tub, etc. so the hose does not pull

out from the force of the water.

3Plug the power cord into a grounded outlet.

4Turn on the power at a circuit breaker/fuse box.

5Carefully slide the washer to its ﬁnal position.

Recheck for level and rock corners for stability.

Remove and discard door tape.

6Read the Use & Care Guide provided with the

washer. It contains valuable and helpful information

that will save you time and money.

7Run the washer through a complete cycle, checking

for water leaks and proper operation.

8If you have any questions during initial operation,

please review the “Service Prevention Checklist” in

your Use & Care Guide before calling for service.

9Place these instructions in a location near the

washer for future reference.

IMPORTANT

Check to ensure the power is off at a circuit breaker/

fuse box before plugging the power cord into an outlet.

NOTE

A wiring diagram and technical data sheet are located

under the washer top panel, on top of the detergent

dispenser housing.

NOTE

The standpipe inside diameter must be 1-1/4” (3.2 cm)

minimum. There must be an air gap around the drain

hose in the standpipe. A snug hose ﬁt can cause a

siphoning action.

Other manuals for FFFW5100PW

Table of contents

Languages:

Other Frigidaire Washer manuals

Frigidaire

Frigidaire 134305700B User manual

Frigidaire

Frigidaire FAHE4044MW0 User guide

Frigidaire

Frigidaire GLWY1343AS1 User manual

Frigidaire

Frigidaire FTF530FS - 27" Front-Load Washer User manual

Frigidaire

Frigidaire GLTF1670 User manual

Frigidaire

Frigidaire WASHER PN 134604400A (0512) User manual

Frigidaire

Frigidaire ATFB7000EP0 User manual

Frigidaire

Frigidaire FFTW1001PW0 Owner's manual

Frigidaire

Frigidaire ATF6500F User manual

Frigidaire

Frigidaire CRWS1879AS0 User manual

Frigidaire

Frigidaire FWS1233FS2 User manual

Frigidaire

Frigidaire FWTE09M3FEJW User manual

Frigidaire

Frigidaire FWX6970E User manual

Frigidaire

Frigidaire FAFW3514KN1 Owner's manual

Frigidaire

Frigidaire FFTW1001PW? User manual

Frigidaire

Frigidaire ATF8000F User manual

Frigidaire

Frigidaire FTF630AS0 User manual

Frigidaire

Frigidaire FAHE1011MW Owner's manual

Frigidaire

Frigidaire FTF2140ES1 User manual

Frigidaire

Frigidaire 131921300 (9912) User manual

Frigidaire

Frigidaire FWS545NB User manual

Frigidaire

Frigidaire GLWY1343AS1 User manual

Frigidaire

Frigidaire FCCW3000ES0 Manual

Frigidaire

Frigidaire Affinity FAFW3511K B User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide