Frigidaire FFFW4000QW0 User manual

TABLE OF

Important Safety InstructLons .............................. 2-3

Installation Requlrements .................................. 4-6

Installat_on Instructlons .................................... 7-10

Accessories ..........................................................

CONTENTS

Notes .............................................................. 12

Franr=als ............................................................ 13

Espafi01 .............................................................. 25

Recognize safety symboisr words

and labels

Safety items throughout this manual are labeled with

a WARNING or CAUTION based on the risk type as

described below:

Definitions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards, Obey all safety

messages that follow this symbol to avoid possible injury

or death.

Shipping Hardware

{3 Foam shipping support (under wash tub)

removed and stored

{3 Shipping bolts and spacers removed from rear

of appliance and stored

[3 Hole plugs (shipped in bag in drum) installed in

holes in backsheet

Leveling

{3 Washer is level, side-to-side and front-to-back

{3 Cabinet is setting solid on all corners

Water Supply

{3 Use only new hoses and verify rubber sealing

washers are installed

{3 HOT supply is connected to HOT inlet and

COLD supply is connected to COLD inlet

{3 HOT and COLD water supply turned on

{3 No leaks present at water supply connections

or appliance inlet connections -

recheck in 24 hours

Drain

{3 Stand pipe or wall drain height minimum 24"

{3 Anti-siphon disc (shipped in drum)installed on

....................................................................................... drain hose

WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious {3 Drain hose secured in place with cable tie

in!uEx:........................................................................................................................................................(shipped in drum)

Electrical Power

{3 House power turned on

CAUTION indicates a potentially hazardous situation {3 Washer plugged in

which, if not avoided, may result in minor or moderate

injury. Final Checks

{3 InstallaUon InstrucUons and Use and Care

Gu,dereadthorough,y

IMPORTANT indicates installation, operation or {3 Door locks and water enters drum when cycle

maintenance information which is important but not starts

hazard-related. {3 Registration card sent in

The electrical service to the washer must conform with

local codes and ordinances and the latest edition of the

National Electrical Code ANSI/NFPA 70 or in Canada

the Canadian Electrical Code C22.1 part 1.

ii!ii:ii!iiii!!i_iiiii_i_ii_iii_ii_!i!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!iiii!i!ii!i!i!!ii!i!i!i!i!i!i!i!i!i!ii!i!i!iiiii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!!!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!!

For your safety the information in this manual must be

followed to minimize the risk of fire or explosion or to

prevent property damage, personal injury or loss of life,

Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

Destroy the carton and plastic bags after the washer is

unpacked. Children might use them for play. Cartons

covered with rugs, bedspreads, or plastic sheets can

become airtight chambers causing suffocation. Place

all materials in a garbage container or make materials

inaccessible to children. installing, operating and maintaining any appliance.

Maximum benefits and enjoyment are achieved

when all the Safety and Operating Instructions are

understood and practiced as a routine with your

laundering tasks.

Save these instructions for future reference,

Tools and materials needed for installation:

OR OR

Adjustable 3/8"or ] 0 mm Ratchet and

wrench box wrench socket set

AND

Adjustable

pliers

AND

Carpenter'slevel

Inlet hose (x2)

Electrical system requirements

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2 wire, with ground, 120 volt single

phase, 60 Hz, Alternating Current.

Because of potentially inconsistent voltage capabilities,

the use of this washer with power created by gas

powered generators, solar powered generators, wind

powered generators or any other generator other than

the local utility company is not recommended.

OUTLET RECEPTACLE- Properly grounded 3-prong

receptacle to be located so the power supply cord is

accessible when the washer is in an installed position.

Groundin_

wall

Power €ord With

B-preng greunded plug

¸I

GFI (Ground Fault Interrupter) receptacle is not

required.

Ground requirements

Water supply requirements

Hot and cold water faucets MUSTbe installed within hose

length of your washer's water inlet. The faucets MUST

be 3/4 inch (1.9 cm) with threading for laundry hose

connection. Water pressure MUST be between 30 and

120 psi. Pressure difference between hot and cold cannot

be more than i0 psi. Your water department can advise

you of your water pressure.

Drain system requirements

1 Drain capable of eliminating 17 gals (64.3 L) per

minute.

2 A standpipe diameter of i-i/4 in. (3.18 cm)

minimum.

3The standpipe height above the floor should be:

Minimum height: 24 in. (6! cm)

Maximum height: 96 in. (244 cm)

96"

(244cm) Illl

max.

Drain hose attached to the washer can reach a 74 in.

(i88 cm) high standpipe. For higher standpipe, use

hose P/N 137098000, available from an authorized

parts distributor.

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check

with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

1 The washer MUST be grounded. In the event of

malfunction or breakdown, grounding will reduce

the risk of electrical shock by a path of least

resistance for electrical current.

2 Since your washer is equipped with a power supply

cord having an equipment-grounding conductor

and a grounding plug, the plug MUSTbe plugged

into an appropriate, copper wired receptacle that is

properly installed and grounded in accordance with

all local codes and ordinances or in the absence

of local codes, with the National Electrical Codes,

ANSI/NFPA 70 (latest edition). If in doubt, call a

licensed electrician. DO NOT cut off or alter the

grounding prong on the power supply cord. In

situations where a two-slot receptacle is present,

it is the owner's responsibility to have a licensed

electrician replace it with a properly grounded three

prong grounding type receptacle.

Clearance requirements

INSTALL YOUR WASHER:

1 In an area exposed to dripping water or outside

weather conditions, The ambient temperature

should never be below 60° F (i5,6 ° C) to

maximize detergent effectiveness.

2 In an area (garage or garage-type building)

where gasoline or other flammables (including

automobiles) are kept or stored.

3 On carpet, Floor MUST be solid with a maximum

slope of 1 inch (2.5 cm). To minimize vibration

or movement, reinforcement of the floor may be

necessary.

Installation in a Recess or Closet

If washer and dryer are installed in the same closet,

door ventilation is required: A minimum of 120 square

inches (774,2 cm 2) of opening, equally divided at the top

and bottom of the door, is required. Louvered openings

should be located 3 inches (7,6 cm) from bottom and

top of door. Air openings are required to be unobstructed

when a door is installed. A Iouvered door with equivalent

air openings for the full length of the door is acceptable.

closet door

MINIMUM INSTALLATION CLEARANCES -Inches (cm)

SIDES REAR TOP FRONT

Alcove 0"(0 cm) 0" (0 cm)* 0" (0 cm) n/a

Under- 0"(0 cm) 0" (0 crn)* 0" (0 cm) n/a

Counter

Closet 0" (0 cm) 0" (0 cm)* 0" (0 cm) 1" (2.5 cm)

1',

o..---_',',_,--

(25cm) (Ocm)

iii1

Washer Dimensions

_49.5" (126 cm) _

to clear open door

freestand washer

on floor

floorline

washer mounted on

optional pedestal

floorline

27,8" (

to front of closed door

Ii f

water supply

connection on

rear of unit

27.0"

(6815 cm)

51,25"

(130 cm)

_50.8"(129 cm)*

to clear open door

floorline

_29.75"(75.5 cm)*_

to front of closed door t

71.5"

(182 cm)

water supply

connection

rear of unit

of gas unit

37"

(94 cm)

electrical

supply on

rear of uniP

centerline

height for

drain hose

_r of

unit 2

39"

(99 cm)

_Connection of water inlet hose on steam dryer adds 3/4 in, (2 cm) to installation depth.

1Power supply cord length on washer approximately 60 inches (152.5 cm),

2Drain hose length on washer approximately 52 inches (132 cm),

3Power supply cord length on gas dryer approximately 60 inches (152.5 cm).

Removing foam packaging

Destroy the carton and plastic bags after the washer is

unpacked.Chitdrenmightusethemforplay,Cartons

covered with rugs, bedspreads, or plastic sheets can

become airtight chambers causing suffocation, Place

aJtmaterials in a garbage container or make materials

inaccessibletochildren,

1 Temporarily remove door tape.

2 Open washer door and remove everything from the

drum.

3 Close door and reapply door tape.

4 Using a rug, blanket or piece of cardboard to

protect the floor, carefully lay the washer on it's

back.

EXCESSIVE WEIGHT HAZARD

To avoid back or other injury have more than one

person move or Iift the washer.

5 Remove styrofoam base and shipping plug and set

them aside.

6 Carefully return the washer to an upright position.

7 Carefully move the washer to within 4 feet (1 m) of

its final location.

Save styrofoam base and shipping plug for use to help

prevent washer damage during any future moves.

Removing shipping hardware

Rubber expansion material on spacers may need

time to relax before they can be easily pulled through

-.... shipping hole.

]'II

, X2

ii/_x4

:/ /,×4

" :............'..... {:_, <{t_<<<<:::::::::::: <9._......, 4 BOLTS

[] 2 P CLAMPS O 4 SPACERS

Remove all of the following:

4 BOLTS O 4 SPACERS

[] 2 P CLAMPS Save all shipping bolts and spacers for future use. If

the washer is to be transported at a later date, the

shipping hardware must be reinstalled to help prevent

sh!pp!ng damage: ..........................................................................................................................................................

Installing hole plugs

A 4 HOLE PLUGS

(IN BAG) I Locate 4 hole plugs in the small bag supplied

with washer instruction guides. Insert them in

the holes in washer back panel.

Leveling your washer

Excessive noise and vibration can be prevented by

properly leveling the washer.

1For free standing installation and with the washer

within 4 feet (1 m) of its final location, place a level

on top of the washer.

2 Use adjustable pliers to adjust the leveling legs so

the washer is level front-to-rear and side-to-side,

and stable corner-to-corner.

3Press down on alternate corners and sides and feel

for the slightest movement. Adjust the appropriate

leg(s) so the washer sits solidly on the floor on

ALL four legs. Keep the leveling leg extension at a

minimum for best performance of the washer.

For pedestal installations, see additional installation

instructions included with the pedestal.

Connecting inlet water

1Run some water from the hot and cold faucets

to flush the water lines and remove particles

that might clog the water valve screens and to

determine which faucet is hot and which is cold

supply.

RUBBER WASHERS

MUST BE PRESENT

USE ONLY

NEW HOSES

Hoses are not included with washer purchase, See

"Accessories" section for various inlet hose kits to fit

your specific installation,

2Connect the HOT inlet hose to the HOT inlet

connection on the washer and the COLD inlet

hose to the COLD inlet connection on the washer.

Tighten by hand until snug. Then tighten each

supply connection another 2/3 turn with pliers.

Do not cross thread or over-tighten these

connections,

3Connect the HOT inlet hose to the HOT water

supply and the COLD inlet hose to the COLD water

supply. Tighten by hand until snug. Then tighten

each supply connection another 2/3 turn with

pliers. Do not bend, kink or pinch water inlet

hoses.

4 Turn on the water and check for leaks.

HOT COLD _, ///

Connecting drain and electrical

1Locate the anti-siphon ring shipped with your

washer. Place it over the end of the drain hose and

slide it past the first ring of "accordion" ribs.

2 Form a "U" shape on the end of the drain hose

with the hose pointed toward the drain. Place the

formed end in a laundry tub or a standpipe and

secure the drain hose with the cable tie (provided

in the enclosure package) to the standpipe, inlet

hose, laundry tub, etc. so the hose does not pull

out from the force of the water.

The standpipe inside diameter must be 1-1/4" (3.2 cm)

minimum. There must be an air gap around the drain

hose in the standpipe. A snug hose fit can cause a

siphoning action.

ION

01SC

$LID'_ DISC

TO HERE

)Check to ensure the power is off at a circuit breaker/

fuse box before plugging the power cord into an outlet.

3 Plugthe power cord into a grounded outlet.

Groundir

ii _

P......dwith

3-pronggroundedplug

4Turn on the power at a circuit breaker/fuse box.

5Carefully slide the washer to its final position.

Recheck for level and rock corners for stability.

Remove and discard door tape.

6 Read the Use & Care Guide provided with the

washer. It contains valuable and helpful information

that will save you time and money.

7 Runthe washer through a complete cycle, checking

for water leaks and proper operation.

8 If you have any questions during initial operation,

please review the "Service Prevention Checklist" in

your Use & Care Guide before calling for service.

9 Placethese instructions in a location near the

washer for future reference.

))A wiring diagram and technical data sheet are located

under the washer top panel, on top of the detergent

dispenser housing.

)!!i!i!l!_!0 ;ii

Table of contents

Languages:

Other Frigidaire Washer manuals

Frigidaire

Frigidaire GLWS1339CC0 User manual

Frigidaire

Frigidaire Gallery 131842800 User manual

Frigidaire

Frigidaire 131843000C User manual

Frigidaire

Frigidaire Gallery GLWS1349AS0 User manual

Frigidaire

Frigidaire BTF2140FS1 User manual

Frigidaire

Frigidaire LCE756A User manual

Frigidaire

Frigidaire FTF2140ES1 User manual

Frigidaire

Frigidaire FWFB9200ES0 User manual

Frigidaire

Frigidaire ATFB7000ES1 User manual

Frigidaire

Frigidaire GLWS1649AS1 User manual

Frigidaire

Frigidaire FAFW3577KA - Affinity Series 27-in Front-Load... User manual

Frigidaire

Frigidaire Gallery FWTR549GG User manual

Frigidaire

Frigidaire GLTF1240AS0 User manual

Frigidaire

Frigidaire CRWS1879AS0 User manual

Frigidaire

Frigidaire GLWS1339C User manual

Frigidaire

Frigidaire FWS745GC User manual

Frigidaire

Frigidaire GLWS1979AS2 User manual

Frigidaire

Frigidaire NMWS336FS0 User manual

Frigidaire

Frigidaire 134670100 User manual

Frigidaire

Frigidaire FTF2140FS2 User manual

Frigidaire

Frigidaire 134566200 User manual

Frigidaire

Frigidaire FTFB4000FS1 User manual

Frigidaire

Frigidaire ATF6000ES User manual

Frigidaire

Frigidaire FAFS4272LR Instruction Manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide