Frigidaire FTF2140ES1 User manual

Full Size Tumble Action Washers

Before beginning installation, carefully read these instructions. This will simplify the

instaffation and ensure the washer is installed correctly and safely. Leave these instructions

near the washer after installation for future reference.

NOTE: The electrical service to the washer must conform with local codes and ordinances

and the latest edition of the National Electrical Code, ANSI/NFPA 70.

For your safety the information in

this manual must be followed to minimize the risk

of fire or explosion or to prevent property damage,

personal injury or loss of life.

- Do not store or use gasoline or other flammable

vapors and liquid in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

.Do not try to light any appliance.

.Do not touch any eIectrica[ switch; do not

use any phone in your building.

. Clear the room, building or area of all

occupants.

.immediately call your gas supplier from a

neighbor's phone. Follow the gas suppliers

instructions.

.if you cannot reach your gas supplier, call

the fire department.

installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

Printed in U.S.A.

Contents

SUBJECT PAGE

Preqnstallation Requirements 2

Electrical Requirements 2

Grounding Requirements 2

Water Supply Requirements 2

Drain Requirements 2

Roughqn Dimensions 3

Location Of Your Washer 4

Unpacking 4

Installation 4-6

Replacement Parts 6

P/N 134594900A (0509)

PRE-INSTALLATION REQUIREMENTS

Tools Required for Installation:

1. Phillips screwdriver

2. 10 mm socketwith ratchet.

3. Channeldock adjustable pliers.

4. Carpenter's level.

ELECTRICAL REQUIREMENTS

CIRCUIT-Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2 wire, with ground, 120 volt, single

phase, 60 Hz,Alternating Current. NOTE: Tile use of this

washerwith power createdbygaspoweredgenerators,solar

powered generators,wind powered generators or anyother

generator other than tile local utility company is not

recommended.

OUTLET RECEPTACLE- Properly grounded 3-prong

receptacle to be located so the power supply cord is

accessible when tile washer is in an installed position.

NOTE: GFI (Ground Fault Interrupter) receptacle is not

required.

GROUNDING REQUIREMENTS

Improper connection of the equipment

grounding conductor (:an result in a risk of electrical

shock. Check with a licensed electrician if you are in

doubt asto whether the appliance isproperly grounded.

.Tile washer MUST be grounded. In the event of

malfunction or breakdown, grounding will reduce

the risk of electrical shock by a path of least

resistance for electrical current.

.Sinceyour washer isequipped with a power supply

cord having an equipment-grounding conductor

and a grounding plug, the plug MUSTbe plugged

into an appropriate, copper wired receptacle that

is properly installed and grounded in accordance

with all local codes and ordinances or in tile

absence of local codes, with tile National Electrical

Codes, ANS!/NFPA 70 (latest edition). If in doubt,

call a licensed electri(ian. DO NOTcut off or alter

the grounding prong on the power supply cord. In

situations where a two-slot receptacle is present,

it is the owner's responsibility to have a licensed

electrician replace it with a properly grounded

three prong grounding type receptacle.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within

42 inches (!07 cm) of your washer's water inlet. The

faucets MUST be 3/4 inch (!.g cm) garden hose type

so inlet hoses can be connected. Water pressure MUST

be between 30 and 120 pounds per squareinch (maximum

unbalance pressure, hot vs. cold, 10 psi.) Your water

department canadviseyou of your water pressure.Tile hot

water temperatureshouldbeabout 140degreesF(60 degrees

DRAIN REQUIREMENTS

1. Drain capable of eliminating 17 gab (64.3 L) per

minute.

2. A standpipe diameter of 1-1/4 in. (3.18 cm)

minimum.

3. The standpipe height above the floor should be:

Minimum height: 24 in. (61 cm)

Maximum height: 96 in. (244cm)

o O0

BACK

96 in.

(244 cm)

Max.

24 in.

(61 cm)

MJn.

NOTE:

Drain hose attached to the washer can reach a go

in. (229 cm) high standpipe. For higher standpipe,

use hose P/N 134369410, available from an

authorized parts distributor.

ROUGH-IN DIMENSION5

27 . 75

.........................................._7o.5_........

24"

(61) ................ -1 .... (

t......................j\ .............................

SIDE

IPower' Cord

33.40

(84 8)

NOTE: For pedestM or undercounter instMladonL reference _5WnstMladon"

_91.3)

With leveling leg

lock nuts removed

2 7 _

...............................................................(6a.8) ...............................................................................

.5 6,75

{ 2:_,f_) (17.)

2 °75

(7}

D_-a;£n

82 _:25

( 81 _9 )

BASK

LOCATION OF YOUR WASHER

DO NOT INSTALL YOUR WASHER:

1. In an area exposed to dripping water or outside

weather conditions. Theambient temperature should

never be below 60° F(!5.6 ° C) for proper washer

(detergent breakdown) operation.

2. Inan area where itwill come in contact with curtains

or drapes.

3. In an area (garage or garage-type building) where

gasoline of other flammables are kept or stored

(including automobiles).

4. On carpet. Floor MUST be solid with a maximum

slope of I/2 in. per foot (1.27 cm per 30.5 cm). To

ensure vibration or movement does not occur,

reinforcement of the floor may be necessary.

IMPORTANT

MINIMUM INSTALLATION CLEARANCES

When installed in alcove or closet:

Sides, Rear= 0 in. (0 cm)

Tap = 0 in. (0 cm)

When installed in closet: Front = 1 in. (2.54 cm)

Closetdoor ventilation required:2 Iouveredopenings each

60 in2(387 cm2),3 in. (7.6 cm) from top and bottom of

door. UNPACKING

1. Cut the shipping carton along the dotted line along

the base of the unit.

2. While in the carton carefully lay the washer on its

back side.

3. Remove the styrofoam base.

4. Carefully return the washer to an upright position

and remove the carton.

5. Carefully move the washer to within 4 feet (122cm)

of the final location.

6. Remove the following from the back panel of the

washer: 4 packaging bolts,

4 spacers,

2 metal "P" clamps,

7. Cover the bolt holes with plugs located inthe

literature bag.

8. Using the shipping posts, prop up the front of the

washer approximatley 2 inches to gain access to

the service panel screws.

g. Remove the 2 screws and remove the service panel.

10. Removethe two (2) styrofoam blocks located under

the drum. Lift up on the drum, tilt the base of the

foam blocks inwards toward the rear of the washer

until free, then pull them out.

11. Replace the service panel and screws.

NOTE; If the washer isto be transported at a later

date, the shipping support hardware must

be reinstalled to prevent shipping damage.

Drain Hose InstMtadon

Thedrain hose isfield installed to allow hose orientation

to the left or right, up or down depending on location of

the house drain. The hose isshipped in the washer tub

with the spring clamp on the coupler elbow and drain

hose hanger installed on the end of the hose.

2. Remove the drain hosefrom the tub of the washer.

Pushthe hose onto the drain coupler at the upper

left of the washer back panel until the hose con-

tacts the STOPRIB.

.RAIN HOSE TABS

SPRING

CLAMP

PROVIDED

', ON HOSE

PUSH HOSE ONTO ----X .... -...... -

COUPLER TO STOP RIB _\ /

.Using pliers, squeeze the ears of the spring (:lamp

and position tile clamp sothe clamp ears_ with

and contact the tabs on the drain hose. This as-

sures proper location of the clamp to prevent leaks.

ALIGN SPRING

CLAMP EARS WITH

TABS ON HOSE

RI{I_'_T_LEFT_ UP

OR DOWN AS _EE_:O

_EF_D_ PLAOING

CL_:P I_ POSITION

- ALWAYSALIQN CLAI£P£_R_;

INSTALLATION

Leve//ng the Washer

Excessive noise and vibration (an be prevented by properly leveling tile

washer and tightening the leveling leg lock r/uts.

1 For free standinq installation and with tile washer in it's tir/al position,

place a level on top ol the washer. Adjust the leveling legs so the

washer is level fror/t-to-rear and side-to-side, and stable corner-to-

corner. Press down on alternate corners and sides and feel for the

slightest movement. Adjust the appropriate leg so the washer is SOLID

on the floor on ALL four legs_ Keep the leveling leg extension at a

minimum for best performance ol the washer.

Once the unit is level and

stable ir/it's final position,turn

tile leveling leg lock nuts

against the base olthe

washer and tighten with a

wrench.

2. For pedestal installations, remove the Iocknuts from each of the

washer legs Reinstall each leg threading all tile way into tile base

(turn each leg tight to tile base) before mounting on tile pedestal

See additional installation instructions included with the pedestal.

3 For undercounter installations the Iockr/uts may need to be removed

before installing. Before installing, verifythere is enough clearance for

tile washer to be installed with the Iocknuts included. If space is not

available, remove the Iockr/uts

from the leveling legs and

reinstall each leg by threading

all the way until tight in the

base. Remove the front

service panel and reinstall tile

Iocknuts on top of the front

(2) leveling legs inside the

washer and tighten against

tile leveling leg bushings once

the unit is in it's final position.

Washer Connections

1 Run some water from the hot and cold faucets to

flush tile water lines and remove particles that might

clog up tile water valve screens.

2 Remove tile inlet hoses and rubber washers from

tile plastic bag located in the drum of the washer

and install the rubber washers ir/each end of tile

inlet hoses.

3. Carefully connect the inlet hose marked "HOT" to the outside "H" outlet

of the water valve. Tighten by hand, then tighten another 2/3 turn with

pliers. Carefully connect the other inlet hose to the inside "C" outlet of

tile water valve Tighten by hand, then tighten another 2/3 turn with

pliers. Do not crossthread or over-dghten these connections.

4. Connect the inlet hose ends to the HOT and COLD water faucets tightly

by hand, then tighten another 2/3 turn with pliers rum tile water or/

and check tor leaks.

NOTE; Use only new hoses.

i:iii

Cable Tie

INSTALLATION (CON'T)

Place the hook end of the drain hose in the drain opening_

Secure the drain hose with the cable tie (provided in the

enclosure package) to the standpipe, inlet hose, laundry

tub, etc_ so the hose does not pull out from the force of the

water

6_ Plug the power cord into a grounded outlet

NOTE: Check to ensure the power is off at acircuit breaker/

fuse box before plugging the power cord into an

outlet,

7 Turn on the power at a circuit breaker/fuse box

8 Read the Operating hstructions and Owner's Guide provided

with the washer They contain valuable and helpful information

that will save you time and money

9 Run the washer through a complete cycle Check for water

leaks and proper operation.

10. ff your washer does not operate, please review the "Avoid

Service Checklist" in your Owner's Guide before calling for

service.

11, Placethese instructions in a location near the washer for future

reference

NOTE: A wiring diagram and technical data sheet are located in

an envelope attached to the left hand side panel on the

inside of the washer

i,i i

Cable Tie

REPLACEMENT PART5

If replacements parts are needed for your washer, contact the source

where you purchased your washer, call 1o800-944o9044, or visit

our website, www_frigidaire corn, for the Frigidaire Company

Authorized Parts Distributor nearest you

Destroy the carton and plastic bags after the washer

is unpacked Children might use them for play. Cartons covered

with rugs, bedspreads, or plastic sheets can become airtight

chambers causing suffocatiom Place all materials in a garbage

container or make materials inaccessible to children.

_The instructions in this manual and all other literature

included with this washer are not meant to cover every possible

condition and situation that may occur Good safe practice and

caution MUST be applied when installing, operating and

maintaining any appliance

Maximum benefits and enjoyment are achieved when all the

Safety and Operating instructions are understood and practiced

as a routine with },our laundering tasks

Other manuals for FTF2140ES1

This manual suits for next models

Other Frigidaire Washer manuals

Frigidaire

Frigidaire Gallery GLTF1240A User manual

Frigidaire

Frigidaire FFFW5000QW Owner's manual

Frigidaire

Frigidaire ltf530fs0 User manual

Frigidaire

Frigidaire FAFW4011LB Instruction Manual

Frigidaire

Frigidaire FAHE4044MW0 User guide

Frigidaire

Frigidaire GLWS1649AS4 User manual

Frigidaire

Frigidaire ATF8000FS - Gallery - Washer User manual

Frigidaire

Frigidaire 134850600B User manual

Frigidaire

Frigidaire FAFW3577KR1 User manual

Frigidaire

Frigidaire FAFW3577KA - Affinity Series 27-in Front-Load... User manual

Frigidaire

Frigidaire ATFB7000ES1 User manual

Frigidaire

Frigidaire LTF2940FS1 User manual

Frigidaire

Frigidaire Gallery FWT647GHS0 User manual

Frigidaire

Frigidaire FAFW3574KB - Affinity Tumble Action Washer User manual

Frigidaire

Frigidaire FFFW5100PW User manual

Frigidaire

Frigidaire MWX233RB User manual

Frigidaire

Frigidaire MWX645RE User manual

Frigidaire

Frigidaire FAFW3574K W User manual

Frigidaire

Frigidaire LTF8000FE0 User manual

Frigidaire

Frigidaire FTFB4000FS0 Instruction Manual

Frigidaire

Frigidaire FWF 81663W User manual

Frigidaire

Frigidaire Full Size Tumble Action Washers User manual

Frigidaire

Frigidaire Gallery GLTF1040A User manual

Frigidaire

Frigidaire 1341085500 User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide