Friedrich SS08 User manual
Window Installation Instructions
Standard Chassis Models
115-Volt:
208-230-Volt:
Room Air Conditioners
93001014_00
SS08, SS10, SS12, SS14, SM15,
SS12, SM18,SM21 SL24, SL28, SL36
115-Volt:
208-230-Volt:
EQ08,YS10
ES12, ES16, YS12, EM18,
YM18, EM24, EL24, EL36, YL24
SYSTEM FANMODE
SCHEDULE FANSPEED
AUTO
AUTO
AUTO
CONTINUOUS
°F °C
17
Airflow Selection and Adjustment
Air flow direction adjustment
left or right side of the discharge opening. Each of the banks of louvers
can be directed left, right, up or down in order to achieve the most optimum
move it in the direction that you would like the air to be directed. Please
louvers than the other.
TO BRING IN FRESH AIR – Move the lever to the Fresh Air position
which allows outside air to enter the room. This is useful in fall and spring as
a means of bringing in fresh outside air when using FAN ONLY . It can also
be used in the summer with the compressor in the Cooling Mode if you wish.
Fresh air and exhaust control
Your air conditioner has the ability to bring fresh air into the room or exhaust
stale air out of the room. The control slide is found on the upper part of
the unit (See Figure 13).
TO EXHAUST INDOOR AIR – Move the lever to the Exhaust
position. This will allow stale air to be expelled to the outside of the dwelling.
This is especially handy in the spring or fall when indoor air tends to get
stale, or after a social gathering involving smokers, or to remove cooking
odors.
BEST PERFORMANCE – Move the lever to the Re-Circulate Position
Figure 13
FRR008
18
MODEL DESIGNATION CABINET SIZE (H x W x D)
SMALL CHASSIS - SS,
ES, YS
15 15⁄16" x 25 15⁄16" x 29" (405 mm x
660 mm x 737 mm)
MEDIUM CHASSIS - SM,
EM, YM
17 15⁄16" x 25 15⁄16" x 29" (455 mm x
660 mm x 737 mm)
LARGE CHASSIS - SL,
EL, YL
20 3⁄16" x 28" x 35 1⁄2" (513 mm x 711
mm x 851 mm)
Table 3
WARNING
Electrical Shock Hazard
Make sure your electrical receptacle has the
same configuration as your air conditioner’s
plug. If different, consult a Licensed Electrician.
Do not use plug adapters.
Do not use an extension cord.
Do not remove ground prong.
Always plug into a grounded 3 prong oulet.
Failure to follow these instructions can result in
death, fire, or electrical shock.
1
2
3
4
65
87
ITEMS NOT TO SCALE
5/16
5/16
1/4
1/4
Recommended Tools
1. Power Drill
2. 5/32" Drill Bit
3. Gloves
4. Carpenters Level
5. 5/16" Wrench
6. 1/4" Wrench
7. #2 Phillips Screw Driver
8. Putty Knife or (wood stir stick)
CAUTION
Excessive Weight Hazard
Use two or more people when
installing your air conditioner.
Failure to do so can result in
back or other injury.
WARNING
MOVING PARTS HAZARDS
* Do not operate unit out of sleeve
or with front grille removed.
* Do not place hands in blower or
fan blade areas.
Failure to do so can result in
serious injury.
Installation Instructions
READ THIS FIRST! Electrical Requirements
IMPORTANT: Before you begin the actual installation of your air
.wolebnoitamrofniehtdnasedoclacirtcelelacolkcehc,renoitidnoc
Your air conditioner must be connected to a power source with the same
alternating current (A.C.) voltage and amperage as marked on the name
plate located on the chassis. Only A.C. can be used. Direct Current (D.C.)
cannot be used.
CIRCUIT PROTECTION – Use on single outlet circuit only. An overloaded
circuit will invariably cause malfunction or failure of an air conditioner,
therefore, it is necessary that the electrical protection is adequate. Due
to momentary high current demand when the air conditioner starts, use a
"TIME DELAY" fuse or a HACR type circuit breaker. Consult your dealer
or power company if in doubt.
Refer to the electrical name plate located on the air conditioner chassis
(See page 2) to determine the correct fuse or circuit breaker amperage
for your model (See Table 1 on Page 6 for electrical receptacle types).
The power cord has a plug with a grounding prong and a matching
receptacle is required.
The following instructions are for standard chassis model groups
sizes listed in Table 3.
19
INSTALLATION HARDWARE AND ACCESSORY DETAIL
FRR009
ITEM 2 ITEM 3
ITEM 4
ITEM 5 ITEM 6
ITEM 1
ITEM 8
ITEM 11
ITEM 7
ITEM 10
ITEMS NOT TO SCALE
ITEM
NO DESCRIPTION QTY.
2
2
1
3
5
4
4
4
SHELL MOUNTING PARTS
SUPPORT BRACKET
SCREW, 10-24 x 1" HEX HEAD
10-24 FLAT WELD NUT
SCREW, SHEET METAL #12 x 2" 7
1
6 2
7
WINGBOARD ANGLE MOUNTING
WINGBOARD ANGLE, TOP
WINGBOARD ANGLE, SIDE
SCREW, SHEET METAL #8 x 38" 2
ITEM
NO DESCRIPTION QTY.
MOUNTING PARTS
SCREW, SHEET METAL #12A x 2”
CHASSIS SEAL GASKET (LIGHT FOAM)
4
13
7
1
NOTE: Kühl + models do not come with window mounting
components. When mounting a cooling and heating model
a window installation kit must be purchased separately.
KWIKS – For all ES and YS models.
KWIKM – For all EM and YM models.
KWIKL – For all EL and YL models.
ITEM 12 ITEM 13 ITEM 14
ITEM 9
1
4
10 4
11
WINGBOARD MOUNTING PARTS
WINGBOARD (MASONITE)
"J" TYPE SPEED NUT
WINGBOARD CLIP (SPRING STEEL)
SCREW, #8 x ½" PHILLIPS TRUSS HD. 4
12 1
13
WINDOW SEALING
WINDOW SEAL GASKET (DARK FOAM)
CHASSIS SEAL GASKET (LIGHT FOAM)
R1 INSULATION PANEL (GREY FOAM) 1
141
8
9
20
Standard Window Installation
NOTE: Hardware and accessories used during installation are shown
on page 18. Each part will be referred as Item No.
STEP 1. Remove the chassis Entrygard retainer by removing the far
right screw (See Figure 14), save this screw to reattach the
chassis retainer after installation (Step 12). Also, remove and
discard the two retainer screws and washers located at the
rear of the unit (See Figure 14).
CAUTION
Handle Use
Use handle on both sides to
pull unit from sleeve.
Do not push, pull or lift from
center of support.
eldnaHesU
snoitacoL
]sedishtob[
FRR011
RETAINER SCREWS
AND WASHERS
FAR RIGHT
SCREW
ENTRYGARD
RETAINER
WIRE
FRR012
CONTROL UNIT
SUPPORT BRACKET
Figure 14
Figure 15
STEP 2. Hold the cabinet stationary, then use the hand grips on both
ends of the control unit support bracket to pull the chassis out
of the cabinet (See Figure 15).
STEP 3. Remove the large white foam blocks used to restrain the
compressor during shipment (See Figure 16). Inspect base
pan for dislodged white foam blocks and remove. Do not
remove any other foam parts.
STEP 4. Anchor the side angles (Item 6) by engaging the tabs of the
lower sill plate (See Figure 17, Detail B-2) with the loops of the
side angle. Engage the tabs of the top angle (Item 5) with the
top loops of the side angle (See Figure 17, Detail B-1). Install
two (2) screws (Item 7) to secure the top angle tabs and the
side angle to the cabinet (See Figure 17, Detail B-1).
21
CAUTION
Remove Shipping Blocks
Prior to operating the unit remove
the foam shipping blocks.
Failure to do so may result in
damage to the unit which is not
covered by the manufacturer’s
warranty!
Figure 16
FRR045
LEFT SIDE
REMOVE AND DISCARD
FOAM BLOCKS
RIGHT SIDE
FAN MOTOR
EVAPORATOR COIL
COMPRESSOR
BACK
TOP VIEW OF UNIT
FRONT
REMOVE AND SAVE
SCREW FOR
RE-INSTALLATION
REMOVE AND DISCARD
SCREWS
NOTE: DO NOT LEVEL the cabinet from front to back. Make sure there
is approximately 3/8” to 1/2” slope (1/8 to 1/4 bubble on level)
toward the outside of the house.
Adjust the support brackets to provide an inside-to-outside slope for excess
condensation drainage (Refer to Standard Window Installation, Figures 19
through 23). Tighten all screws.
Alternate support method A: If you have a wide window sill which prevents
:gniwollofehtyrt,22erugiFninwohssastekcarbehtgnitnuommorfuoy
Using the elongated holes and different hole locations in the cabinet,
.)22erugiF(thgiews’tinuehttroppusottekcarbehtfotnemecalpehttes
Tighten all screws.
Alternate support method B: If the window ledge gap is narrow, try the
as shown in Figure 23. Bend the short piece so it will be vertical when
installed. Adjust the placement as required. Tighten all screws.
STEP 8.
.)42erugiF(.tenibacdnaslennahcediswodniwehtneewteb
Make sure you include the depth of the window channel.
STEP 5. Check the window sill and frame to be sure they are in good
STEP 6. CABINET MOUNTING – Raise the lower window 1/4" more
than the height of the cabinet. Carefully slide the cabinet
through the opening until the lower sill plate channel rests
behind the window sill and the top angle rests against the
window (See Figure 18). Center the cabinet within the
opening. Drill three (3) 5/32" diameter pilot holes into window
sill using the holes in the cabinet sill plate as a guide. Install
three (3) #12 x 2" long screws (Item 4) (See Figure 18).
STEP 7. OUTSIDE SUPPORT MOUNTING – Refer to Figures 19 and
20. Assemble the support brackets (Item 1) to the bottom of
the cabinet with four (4) 10-24 1” long screws (Item 2) and four
combination of the elongated holes of the bracket and different
hole locations in the cabinet, to bring the bottom support bracket
pads in contact with the wall. A 1" x 4" or 2" x 4" SPACER
SHOULD BE USED BETWEEN THE WALL AND SUPPORT
THE BRACKETS WHEN INSTALLED ON ALUMINUM OR
VINYL SIDING. Drill 5/32" diameter pilot holes and secure
the brackets to the wall with two (2) 12A x 2" long screws
(Item 4).
NOTICE
For YOUR security and safety, YOU must
provide a means of preventing the upper
part of the window from opening.
STEP 9. To assemble the wingboard panels, push on the "J" type speed
nuts (Item 9) and spring steel clips (Item 10) (See Figures 25)
on page 26. Secure each panel with two (2) screws (Item 11).
22
FRR013
TOP ANGLE (ITEM 5)
DETAIL B-2
DETAIL B-1
SILL PLATE
TAB
SIDE ANGLE
(ITEM 6)
2 REQUIRED
#8 x 3/8” LONG SCREW
(ITEM 7) 2 REQUIRED
CABINET
TAB
TAB
LOOP
Figure 17
FRR014
LOCATE SILL PLATE GUIDE CHANNEL
JUST BACK OF WINDOW SILL
WINDOW SILL
TOP ANGLE
(ITEM 5)
SIDE ANGLE
(ITEM 6)
PULL WINDOW
SASH DOWN
BEHIND TOP
ANGLE
CENTER
CABINET
IN WINDOW
SIDE TO SIDE
DRILL (3) 5/32” DIA.
PILOT HOLES AND
INSTALL (3) #12 x 2”
LONG SCREWS
(ITEM 4)
Figure 18
23
FRR015
#12 x 2” SCREW
(ITEM 4)
SPACER SHOULD BE USED BETWEEN
WALL AND BRACKET WHEN INSTALLED
ON ALUMINUM OR VINYL SIDING.
SUPPORT BRACKET
(ITEM 1)
SUPPORT
BRACKET
(ITEM 1)
#10-24 x 1” HEX HD.
SCREW (ITEM 2)
3/8” SLOPE DOWN
10-24 x FLAT WELD
NUT (ITEM 3)
Figure 19
FRR016
#12 x 2” SHEET METAL
SCREW (ITEM 4)
SPACER SHOULD BE USED BETWEEN
WALL AND BRACKET WHEN INSTALLED
ON ALUMINUM OR VINYL SIDING.
3/8” SLOPE DOWN
CONDENSER
AIR OUTLET
CONDENSER
AIR INLETS
#10-24 SCREW
#10-24 FLAT WELD NUT
Figure 20
24
FRR017
#12 x 2” SHEET METAL
SCREW (ITEM 4)
SPACER
3/8” SLOPE DOWN
STONE LEDGE
CONDENSER
AIR INLETS
#10-24 SCREW
#10-24 FLAT WELD NUT
Figure 21
FRR018
3/8” SLOPE DOWN
STRAIGHTEN TAB TO LAY FLAT
ALONG THE BOTTOM RAIL OF
THE SHELL
SECURE THE LONGEST SIDE OF
THE BRACKET TO THE SHELL
STONE LEDGE
#10-24 SCREW
#10-24 FLAT WELD NUT
ADJUST IN OR OUT TO REST
ON THE LEDGE
Figure 22
25
FRR020
MEASURE DISTANCE “B” TO INSIDE OF THE
CHANNEL ON EACH SIDE.
SUBTRACT 1/8” FROM DIMENSION “B” AND
MEASURE FROM THE EDGE OF THE WING-
BOARD (ITEM 8), MARK, SCORE AND CUT
WITH APPROPRIATE CUTTING TOOL.
CUT HERE AND DISCARD CENTER WASTE
MATERIAL.
WINGBOARD
B
B
B
B
FRR019
DIMENSION “A”
CUT
HERE
DISCARD
SHADED AREA
CUT TO FIT DIMENSION “A”
AND BEND DOWN TO FORM
A VERTICAL LEG.
STONE LEDGE
OUTSIDE WALL
A
3/8” SLOPE DOWN
#10-24 SCREW
#10-24 FLAT WELD NUT
Figure 23
Figure 24
Other manuals for SS08
3
This manual suits for next models
20
Table of contents
Other Friedrich Air Conditioner manuals
Friedrich
Friedrich Chill CP12G10B User manual
Friedrich
Friedrich M21DYF Quick setup guide
Friedrich
Friedrich XQ05J10A-B User manual
Friedrich
Friedrich Floating Air Pro Multi-Zone FPHMR42A3A User manual
Friedrich
Friedrich SP05 User manual
Friedrich
Friedrich MR24UY3J User manual
Friedrich
Friedrich The Insider User manual
Friedrich
Friedrich WallMaster PACKAGED TERMINAL AIR CONDITIONERS AND HEAT... User manual
Friedrich
Friedrich CP06C10 Building instructions
Friedrich
Friedrich MWM36Y3J User manual
Friedrich
Friedrich Vert-I-Pak A-Series User manual
Friedrich
Friedrich Uni-Fit UE10C33 Thru-the-Wall Series Building instructions
Friedrich
Friedrich QuietMaster SL25 User manual
Friedrich
Friedrich ZQ08A10C Building instructions
Friedrich
Friedrich WallMaster 2009 User manual
Friedrich
Friedrich MC24Y3F User manual
Friedrich
Friedrich UE08A13A User manual
Friedrich
Friedrich CP14-18-24 CP14N10 Building instructions
Friedrich
Friedrich MS24Y3F User manual
Friedrich
Friedrich ZQ08C10 Building instructions
Popular Air Conditioner manuals by other brands
Fujitsu
Fujitsu Inverter ASBA30JFC operating manual
Toshiba
Toshiba RAS-M10SMUV-E installation manual
Daikin
Daikin FXLQ20MAVE Operation manual
Hitachi
Hitachi RAS-E24CAK instruction manual
CIAT
CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance
Bestron
Bestron AAC6000 instruction manual
