First Alert FA 270 User manual

FIRST ALERT

INSTRUCTION MANUAL

FOR FA 270 KEYPADS

SECURITY SYSTEM

Page 0

Table of Contents

Introduction………………………………………………………………………………… 1

System Basics…………………………………………………………………………….. 1

Burglary Protection……………………………………………………………….. 1

Fire Protection…………………………………………………………………….. 1

Security Codes……………………………………………………………………. 1

Zones and Partitions……………………………………………………………… 1

Arming & Disarming…………………………………………………………….… 2

Alarms……………………………………………………………………………… 2

Memory of Alarm………………………………………………………………….. 2

Phone Access…………………………………………………………………….. 2

Functions of the Keypad…………………………………………………………………. 2

Purpose of Number Keys………………………………………………………………… 2

Function Keys……………………………………………………………………………… 3

LED Indicators……………………………………………………………………………… 3

Entry / Exit Delays………………………………………………………………………… 3

Checking for Faulted Zones……………………………………………………………… 4

Arming your ATP ALARMS First Alert System………………………………….. 4

Arming Modes……………………………………………………………………... 4

Arming Commands……………………………………………………………….. 5

Disarming your System………………………………………………………………...… 6

Bypassing a Zone………………………………………………………………………… 6

Chime Mode……………………………………………………………………………….. 7

Trouble Alerts……………………………………………………………………………… 7

Low Battery……………………………………………………………………….. 7

Fire Trouble……………………………………………………………………….. 7

AC Power………………………………………………………………………….. 7

Accidental Alarms…………………………………………………………………………. 7

When a Burglary Occurs…………………………………………………………………. 8

Fire Alarm………………………………………………………………………………….. 8

Silencing Fire Alarm and Clearing Memory……………………….……………………. 9

Smoke Detector Reset……………………………………….…………………………… 9

Programming Security Codes…………………………………………………………… 9

Arming Difficulty…………………………………………………………………………… 9

Pass Card…………………………………………………………..…………….. 10

Alarm Maintenance and Testing…………………………………………………………. 10

Page 1

Introduction

Congratulations on your ownership of a First Alert security system from ATP ALARMS. You’ve

made a wise choice, for it represents the latest in security protection technology today. This system

provides:

•Three forms of protection: burglary, fire* and emergency

•At least one keypad which provides control of the system and displays system status.

•Various sensors for perimeter and interior burglary protection

•Smoke or combustion detectors* designed to provide early warning in case of fire.

Your system may also have been programmed to automatically send alarm or status messages over

the phone lines to our ULC co-listed Central Monitoring Station located right here in the Okanagan.

*Commercial installations and some residential systems may not include fire protection –

Confirm your system status through our office.

System Basics

Burglary Protection

•There are several modes of burglary protection: Stay, Night-Stay, Away, Instant, & Maximum.

STAY: arms perimeter zones only the entry delay is on. INSTANT: same as STAY, except the

entry delay is off. NIGHT-STAY: arms perimeter zones and selected interior zones; entry

delay on. MAXIMUM: same as AWAY, except entry delay is off

•You can BYPASS selected zones while leaving the rest of the system armed.

•Chime mode alerts you to the opening of protected doors and windows even while the system

is disarmed.

Fire Protection

•Fire protection is always active (if installed) and an alarm sounds if a fire condition is detected.

•Refer to the Fire Alarm System section for information regarding fire protection & smoke

detectors.

Security Codes

•You were assigned a 4-digit security code during system installation.

•Use your security code when arming and disarming the system, and when performing other

system functions.

•Other users should be assigned different security codes, each can have different authority

levels, which define the system functions that particular user can perform.

Zones and Partitions

•The system sensing devices have been assigned to various “zones,” which are specific areas

of protection (e.g. front door, kitchen window, etc.)

•Zone numbers are displayed at the keypad when an alarm or trouble condition occurs on a

sensor

•Partitions provide independent areas of protection, with each partition containing a group of

zones that can be armed and disarmed without affecting other zones or users.

•Partitioned systems can include a common zone area, which is an area shared by users of

both partitions (such as a lobby in a building)

Page 2

Arming & Disarming Burglary Protection

•The system must be armed before the burglary protection can sense intrusions.

•To arm your system, enter your security code followed by the desired arming mode key.

•To disarm the system, enter your user code then press the 1 OFF key.

Alarms

•When an alarm occurs, both the keypad and external sounder will sound, and the keypad will

display the zone(s) causing the alarm

•An alarm message will also be sent to our monitoring station.

•To stop the alarm from sounding, and to cancel the police response, simply disarm the

system. A “Cancel Alarm” signal will be sent to our monitoring station.

Memory of Alarm

•When an alarm condition occurs, the keypad displays the number(s) of the zone(s) that

caused the problem, and displays the type of alarm (e.g. 01 ALARM FIRE or 05 Alarm for a

burglary.)

•The message remains displayed even after disarming the system. To clear the memory, enter

your security code into the keypad and select 1 OFF again.

Phone Access

•If included, a phone Module permits you to access the system via a touch-tone phone, either

on-premises or by calling-in when away.

•You can receive synthesized voice messages over the telephone regarding the status of the

security system

•You can arm and disarm the system and perform most function commands remotely via the

telephone, with voice confirmation provided after each command.

•Refer to the Phone Access User’s Guide supplied with the Phone Module for information

regarding the use of this feature.

Functions of the Keypads

NOTE: The numbers printed boldly directly on the keys indicate their primary purpose; the functions

printed smaller on the keys indicate their alternate or secondary purpose.

Primary Purpose of Number Keys

KEYS 0-9: Used to enter your security code(s) and to perform their associated system function

after the security code has been entered.

Secondary Purpose of Number Keys

1 OFF Disarms burglary portion of the system, silences alarms and audible trouble indicators,

and clears visual display after problem’s correction

2 AWAY Arms the entire burglary system, perimeter and interior.

3 STAY Arms perimeter portion of burglary system only. Interior protection is not armed,

allowing movement within premises without causing an alarm. If pressed twice in

succession and your system is set up for Night-Stay Mode arming, your alarm will be

armed in Night-Stay mode.

Page 3

4 MAX Arms the entire burglary system, perimeter and interior, but without the entry delay

feature. Entering even via an entry/exit door will cause an instant alarm.

5 TEST Tests the system and alarm sounder if disarmed.

8 CODE Used to assign additional user codes and attributes for other users of the system.

6 BYPASS Removes individual protection zones from being monitored by the system.

7 INSTANT Arms in manner similar to the STAY mode, but without the entry delay time.

9 CHIME Turns CHIME mode on and off. When on, the opening of windows or doors while the

system is disarmed sounds 3 beeps at the keypad(s)

* READY Used to display open protection zones.

FUNCTION KEYS

The function keys on the left side of your keypad(s) have been programmed for your

convenience. Check with your installer for their function as it relates to your specific system

RED ARMED INDICATOR: (LED) Lit when the system has been armed

GREEN READY INDICATOR: (LED) Lit when the system is ready to be armed (no faults present).

While the system is disarmed, this indicator will go on and off as protection zones are closed or

opened.

INTERNAL SPEAKER: The built in speaker mimics the alarm sounder during alarms, and will also

“beep” during certain system functions. The speaker can also provide voice playback of recorded

messages to family members when this option has been selected.

Entry & Exit Delays

Your system has preset time delays, known as exit delay and entry delay.

Exit Delay gives you time to leave through the designated exit door(s) without setting off an alarm.

The exit delay begins immediately after arming your system in any arming mode and displays the

message, You May Exit Now. When, You May Exit Now disappears, the system is fully armed.

Exit Delay Restart. If you wish to open the entry/exit door to leave home while other family members

remain inside, or to let someone in or out after arming in the STAY MODE you can restart the exit

delay at any time. Simply press the [ * ] key, then open the door. In addition, opening and closing

the entry/exit door before the exit delay time expires (e.g., re-entering to get a forgotten item) will

reset the exit delay time once.

Entry Delay gives you time to disarm the system when you re-enter through the designated entrance

door. You must disarm the system (simply enter your security code followed by the 1 OFF key) before

Page 4

the entry delay period ends, or an alarm will occur. The keypad beeps during the entry delay period,

reminding you to disarm the system.

You can also arm the system with no entry delay at all by using the INSTANT or MAXIMUM arming

mode. These modes can provide greater security while on the premises with all family members

inside or while away for extended periods of time.

Checking For Faulted Zones

Using the [ * ] Key

Before arming your system, all protected doors, windows and other protection zones must be closed

or bypassed, otherwise the keypad(s) will display a Not Ready message. Use the [ * ] READY key to

display all faulted zones, making it easier for you to identify and secure any open zone.

Arming your ATP ALARMS First Alert System

•Ensure that the green Ready Light is illuminated. The display should only read AC (simply to

show that there is AC power to the system.

•If the green Ready Light is not on, the display will read NOT READY. You can see which

zones are faulted by pressing the “star” key [*]

oA fault is when a window, or door is open, or when there is movement in front of a

motion detector.)

oExample: 08.

This indicates that Zone 8 is open.

•Once you have corrected the fault (i.e. closed the door) the green ready light will turn on and

the display will read AC and the green Ready Light will be illuminated.

•If the fault condition cannot be corrected:

oCall ATP Alarms at (844) 287-2576

(844)/ATP-ALRM-OR-

oYou may also choose to bypass the zone using the procedure listed in on page 6.

Arming Modes

The alarm can be armed to several “modes” or levels of armed. These are:

Stay Mode: Arms Perimeter Only, Entry Delay On

•Used when you want to arm the system with persons staying inside or if there are pets

that are moving through the premises.

•The perimeter windows and doors are armed while the interior sensors are left inactive.

•The exit delay begins when you arm the system (you may leave through the entry/exit

door if desired)

•An alarm sounds if any protected window or non-entry/exit door is opened.

•You may otherwise move freely within the premises.

•Persons entering later can enter through an entry/exit door, but must disarm the system

within the entry delay period to avoid sounding an alarm.

Page 5

•To exit the premises after the exit delay has expired, press the [ * ] key to start an exit

delay.

Night-Stay Mode: Arms Perimeter Only, Plus Selected Zones

•Arms same as Stay mode, but also arms pre-selected interior sensors. (e.g. a basement

motion detector.)

•Persons entering later can use entry/exit doors but they must disarm the system and must

not violate any of the programmed interior zones to avoid sounding an alarm.

•IMPORTANT: When Night-Stay mode is on, the selected interior zones are armed and

cause an alarm if anyone enters those areas. (e.g. , walking in the middle of the night). To

avoid sounding an alarm, you must disarm the system before any activity takes place in

those interior zones.

•To exit the premises after the exit delay has expired, press the [ * ] key to start an exit

delay.

Instant Mode: Arms Perimeter Only, No Entry Delay

•Used when staying inside and you do not expect anyone else to come home.

•Arms the same zones as stay mode

•An alarm sounds immediately if any protected perimeter window or any door is opened,

including entry or exit doors.

•To exit the premises after the exit delay has expired, press the [ * ] key to start an exit

delay.

•IMPORTANT: Arming in this mode greatly increases the chance of accidental activation.

Away Mode: Arms Entire System Entry Delay On.

•Used when nobody will be staying inside.

•The entire system (interior and perimeter) is armed.

•Exit delay begins when you arm the system allowing you to leave through the entry/exit

door.

•An alarm sounds if there is any movement detected inside the premises or if any door or

window is opened.

•You can reenter through the entry/exit door only and must disarm the system within the

entry delay time.

Maximum Mode: Arms Entire System, Entry Delay Off

•Used when leaving the premises for extended periods (e.g., vacation)

•Arms the same zones as Away mode, but entry delay is off.

•An alarm sounds same as Away mode, and sounds upon opening entry/exit doors.

NOTE: This mode should only be used if Phone Module is installed.

Arming Commands

Mode Press these Keys… Keypad Confirms By…

Stay Security code + 3 STAY •STAY message displayed

•Red ARMED indicator light

•Three Beeps

Page 6

Night-Stay Mode Security Code + 3 STAY + 3 STAY •STAY NIGHT message displayed

•Red ARMED indicator light

•Three Beeps

Instant Mode Security code + 7 INSTANT •STAY INSTANT message

displayed

•Red ARMED indicator light

•Three Beeps

•Note that entry delay is turned off

Away Mode Security Code + 2 AWAY •AWAY message displayed

•Red ARMED indicator light

•Two Beeps

•Leave premises through an

entry/exit door during the exit delay

period to avoid causing an alarm.

The keypad beeps rapidly during

the last 10 seconds of the exit

delay to warn you that it is ending.

Maximum Mode Security Code + 4MAX •AWAY INSTANT message

Displayed

•Red ARMED indicator light

•Two Beeps

•Same as Away (described above)

•Note that entry delay is turned off.

Disarming your system

•When you return and enter through the entry/exit door an entry delay timer will start

(usually 30 seconds.)

•A “pre-alarm” entry warning will sound.

•Enter your Security Code + 1 OFF

1. the red armed light will go off

2. The key pad will “beep” once

Bypassing a Zone

The 6 BYPASS key is used to disable individual zones.

•You can only bypass and un-bypass zones when the system is not armed.

•You cannot bypass 24-hour fire and emergency zones.

•Bypassed zones will automatically become un-bypassed when the system is disarmed.

•Bypassed zones are unprotected and will not cause an alarm if violated.

To Bypass:

•Enter your security code + 6 BYPASS

•Enter the 2-digit zone number(s) for the zone(s) to be bypassed. Single digit zones must be

preceded by a zero (e.g. 05, 06)

Page 7

•The keypad will display a Bypass message for each bypassed zone number. Wait for all

bypassed zones to be displayed. Arm the system as usual. When armed, the arming message

is displayed with “BYPASS.”

•To display bypassed zones: security code + 6 BYPASS + [ * ]

NOTE: Once a zone(s) is bypassed, you can un-bypass the zone(s) by entering your Security Code

+ 1 OFF

Chime Mode

To turn Chime Mode on or off:

Security code + 9 CHIME

Chime mode alerts you to the opening of a perimeter door or window while the system is disarmed.

When chime mode is activated:

•Three tones sound at the keypad whenever a perimeter door or window is opened.

•The keypad will display CHIME

•Interior zones do not produce a tone when they are faulted.

•Chime mode can be used only while the system is disarmed.

Trouble Alerts

The word CHECK on the keypad’s display, accompanied by a “beeping” at the keypad, indicates a

trouble condition in the system.

•To silence a system trouble, enter your security code and 1 OFF key.

•A Trouble will not prevent the arming of the system

Low Battery

If the system notices that the battery is low, a BAT message will appear on the keypad and the

keypad will chime.

•To silence the trouble condition enter your security code and 1 OFF key.

•Call ATP 287-2576(844)/ATP-ALRM(844)atAlarms

Fire Trouble

In the event of a Fire Trouble the display will read 01 FIRE CHECK & the keypad will beep

continuously.

•To silence the trouble conditions enter your security code and 1 OFF key.

•Call ATP 287-2576(844)/ATP-ALRM(844)atAlarms

AC Power Failure

The Display should always read AC in the top right portion of the screen. When AC power is cut off to

the system, the display will read NO AC in the top right part of the screen.

During brief power loss:

•Your security system will function normally on its rechargeable battery.

•Normal standby time is at least 4 hours.

Accidental Alarm Activations

Page 8

In the event of accidental alarm activation:

•Enter your Security Code.

•This will send an Automatic Cancel Code to the Central Station.

•The Central Station will cancel the Police.

•No further action is required. However, you may call the Central Station and report the error.

Your conversation with the operator will confirm the system is working properly.

•Be prepared to give the operator your system number and your access code.

* NOTE: When in doubt, assume that the alarm condition is real.

When a Burglary Alarm Occurs

•The siren will sound for 4 minutes.

•The system will automatically dial the Central Monitoring Station and report the nature

and location of the alarm.

oThe system will seize your phone line and report the alarm.

•The Central Station personnel will:

oDispatch the proper authorities.

oContact a property reference to attend.

•After 4 minutes:

oThe alarm siren will turn off.

oThe keypad will read Alarm followed by a zone description. (e.g. 08 ALARM )

•When the property reference enters the location, the keypad will emit a “Pre-Alarm”

warning.

oWhen the property reference enters a valid security code:

The alarm will disarm.

The system will report an “Automatic Cancel Code” to the Central Station.

The phone will be temporarily disconnected as the Cancel Code is reported.

NOTE: The property reference should not enter the site unless accompanied by the police.

IMPORTANT: Whenever you return and see the display: “ALARM” LEAVE IMMEDIATELY

and call the Central Station or the police.

Fire Alarm

General

Your fire alarm system (if installed) is active 24 hours a day, for continuous protection. In the event of

an emergency, the strategically located smoke and/or heat detectors will sound their alarms and

automatically send signals to your system, triggering a loud, interrupted pulsed sound from the

keypad(s) and any external sounders. A FIRE message will appear at your Keypad and remain on

until you silence the alarm (see below for silencing fire alarms).

When a Fire Alarm occurs or you become aware of a fire emergency before your smoke or heat

detectors sense the problem:

Table of contents

Other First Alert Security System manuals

First Alert

First Alert ReadyGuard-RI User manual

First Alert

First Alert CO600 User manual

First Alert

First Alert DWB-700 User manual

First Alert

First Alert 1501 User manual

First Alert

First Alert SC9120B User manual

First Alert

First Alert FA168CPS Series User manual

First Alert

First Alert CO615 User manual

First Alert

First Alert ONELINK CM2837 Instruction Manual

First Alert

First Alert FA1670C User manual

First Alert

First Alert FA1220C User manual

First Alert

First Alert ReadyGuard User manual

First Alert

First Alert FA150C User manual

First Alert

First Alert FA848C User manual

First Alert

First Alert Hearing Impaired Strobe Lights SL177 User manual

First Alert

First Alert FA1660C Assembly instructions

First Alert

First Alert FA1340C-UL User manual

First Alert

First Alert FA140C User manual

First Alert

First Alert D-520 User manual

First Alert

First Alert FA848C Assembly instructions

First Alert

First Alert FA168CPS / FA168CPSSIAA168CPSSIAA168CPSSIAA168CPSSIAFA148CP / FA148CPSIAFA148CP /... Assembly instructions

First Alert

First Alert FA120C User manual

First Alert

First Alert FA168CPS Series User manual

First Alert

First Alert FA110C User manual

First Alert

First Alert FAS-124 User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual