Federal Signal Corporation VISION Quick guide

VISION®

WARNING SYSTEM

OPERATION AND CONFIGURATION INSTRUCTIONS

GENERAL SOFTWARE

Version 2.0

Price $15.00

TABLE OF CONTENTS

Paragraph Page

SECTION I - OPERATION

1-1 General ........................................................................................................................ 1-2

1-2 Power-up ...................................................................................................................... 1-2

1-3 Led Illumination Intensity Adjustment. .................................................................... 1-3

1-4 Foot Switch .................................................................................................................. 1-3

1-5 SS2000 SmartSiren® Interface. ................................................................................. 1-3

1-6 Keyboard Configurations

A. Keyboard Configuration 2 (POLICE A) ........................................................ 1-4

B. Keyboard Configuration 3 (POLICE B) ........................................................ 1-5

C. Keyboard Configuration 4 (FIRE A) ............................................................. 1-7

D. Keyboard Configuration 5 (FIRE B) ............................................................. 1-8

E. Keyboard Configuration 6 (RECOVERY)..................................................... 1-9

F. Keyboard Configuration 7 (CLEARBOARD) ............................................... 1-11

G. Keyboard Configuration 8 (DEMO) .............................................................. 1-11

SECTION II - CONFIGURATION

2-1 General ........................................................................................................................ 2-1

2-2 Sample Configuration Session

A. Enter Configuration Mode ............................................................................ 2-1

B. Level 1 Configuration .................................................................................... 2-2

C. Level 2 Configuration .................................................................................... 2-3

2-3 Configuration Restrictions .......................................................................................... 2-8

2-4 Configuration Worksheet ............................................................................................ 2-9

2-5 Test After Configuration ............................................................................................. 2-9

2-6 Configuration Mode Disable/Enable

A. Disable............................................................................................................ 2-9

B. Enable ............................................................................................................ 2-9

2-7 Configuration Quick Reference

A. Level 1 Configuration .................................................................................... 2-9

B. Level 2 Configuration .................................................................................... 2-11

SECTION III - MICROPROCESSOR INSTALLATION

3-1 General ........................................................................................................................ 3-1

3-2 Installation

A. Control Head .................................................................................................. 3-1

B. Interface/Relay Unit ...................................................................................... 3-1

C. Bar Controller ................................................................................................ 3-1

3-3 Software Revision Label Installation ......................................................................... 3-2

SECTION I

OPERATION

SAFETY MESSAGE TO OPERATORS OF

FEDERAL SIGNAL LIGHT SYSTEMS

WARNING

The lives of people depend on your safe opera-

tion of Federal products. It is important to read and

follow all instructions shipped with the products. In

addition, listed below are some other important

safety instructions and precautions you should

follow:

QUALIFICATIONS

• To properly use a light system: you must have a

good understanding of general vehicle operation, a

high proficiency in the use of safety warning equip-

ment, and thorough knowledge of state and federal

UNIFORM TRAFFIC CODES.

SIGNALING LIMITATIONS

• Be aware that the use of your visual signaling

devices does not give you the right to force your way

through traffic. Your emergency lights and actions

are REQUESTING the right-of-way.

• Although your warning system is operating

properly, it may not alert everyone. People may not

hear, see, or heed your warning signal. You must

recognize this fact and continue driving cautiously.

• Situations may occur which obstruct your

warning signal when natural or man-made objects

are between your vehicle and others, such as when

you raise your hood or trunk lid. If these situations

occur, be especially careful.

• The control head’s LED display simulates the

light pattern(s) being executed by the warning

system. The display is intended ONLY as a guide and

NOT as an indication of proper warning system

operation. Before using the warning system, its

operation should be observed from outside the

vehicle.

DRIVING LIMITATIONS

• At the start of your shift, you should ensure that

the light system is securely attached to the vehicle

and operating properly.

• If the unique combination of emergency vehicle

equipment installed in your vehicle has resulted in

the light/siren controls being installed in a position

that does not allow you to operate them by touch

only, OPERATE CONTROLS ONLY WHILE YOUR

VEHICLE IS STOPPED.

• If driving conditions require your full attention,

you should avoid operating the light/siren controls

while the vehicle is in motion.

CONTINUING EDUCATION

• File these instructions in a safe place and refer

to them periodically. Give a copy of these instructions

to new recruits and trainees.

Failure to follow these safety precautions may

result in property damage, serious injury, or death to

you, to passengers, or to others.

1-1

1-1. GENERAL.

IMPORTANT

Since most Vision features are programmable,

operation is described only for the “standard”

keyboard configurations. System configura-

tion and any changes to the “standard” key-

board configurations (if any) MUST be provided

to the operator by the installer or person re-

sponsible for programming. It is the operator’s

responsibility to understand how his particular

system is configured (programmed) to operate.

The Vision control head is designed to assist the

operator’s selection of functions. Each control head

switch is recessed and aids guiding the operator’s

finger to the switch’s center for activation. When a

switch is pressed, “tactile feedback” provides function

selection indication as follows: a click is felt, a beep is

heard, the selected function’s LED is illuminated,

and the control head’s V-shaped LED display indi-

cates which warning system lights are illuminated. If

the optional SignalMaster directional light is in-

stalled, the control head display simulates the

directional light pattern being executed.

The control head switches are grouped and

color-coded red, amber, and green to indicate the

priority level. Switches that are color-coded red have

the highest priority. Amber color-coded switches have

a lower priority than the red switch group, and the

green color-coded switches have the lowest priority.

Seven selectable “standard” keyboard configura-

tions are available. Each keyboard configuration has

a different function assigned to the keyboard

switches. Only one keyboard configuration can be

selected at a time. System operation is different for

each keyboard configuration. Keyboard configuration

selection (described in Section II) is performed, if

required, when the warning system is installed.

The seven keyboard configurations’ names

suggest a possible application as follows:

• Keyboard Configuration 1 (Federal Signal

use only).

• Keyboard Configuration 2 (POLICE A).

• Keyboard Configuration 3 (POLICE B).

• Keyboard Configuration 4 (FIRE A).

• Keyboard Configuration 5 (FIRE B).

• Keyboard Configuration 6 (RECOVERY).

• Keyboard Configuration 7 (CLEAR-

BOARD).

• Keyboard Configuration 8 (DEMO - sales

use only).

WARNING

Peoples’ lives depend on your safe operation

of this warning system. Ensure that you are

thoroughly familiar with the selected keyboard

configuration’s function selection and warning

system operation.

1-2. POWER-UP.

The Vision warning system does not have a

separate on-off switch. It is usually wired to the

vehicle’s ignition switch and is enabled when the

vehicle’s ignition switch is “on”.

If a user-supplied switch is installed, enable the

system by operating the switch to its “on” position.

CAUTION

The Vision warning system draws approxi-

mately 2.5A (all functions deactivated) and

will eventually discharge the vehicle battery.

Do not leave the system powered-up unless

the vehicle engine is running.

After power is applied, the system will power-up

as follows:

A. The RESET LED will flash for approxi-

mately four seconds to indicate that the system is

performing a self-test. During the self-test, the

keyboard will not operate the warning system and

the reflectors in the lightbar will rotate to the “home”

position.

B. After the self-test is completed, the RESET

LED changes from flashing to steady illumination. In

addition, the control head will sound a beep to

indicate the warning system is now ready for use.

NOTE

If the self-test is unsuccessful, the V-shaped

LED display and directional SignalMaster

LED display will flash and a beeping self-test

failure signal will sound. This failure indica-

tion may be caused by lamp failure, communi-

cation link failure, or other failure.

Press the RESET switch to clear the failure

indication. If the failure indication is cleared,

observe for proper warning system operation

from outside the vehicle. Lamps are tested

only once during power-up and should be

observed from outside the vehicle. If the fail-

ure indication is persistent, the warning sys-

tem should be serviced before use.

1-2

1-5. SS2000 SMARTSIREN INTERFACE.

If the SS2000 SmartSiren interface is installed,

operate switch 8 (usually Mode 3) or the foot switch

to activate the SS2000 pursuit function. The

SS2000’s Mode 3 will be activated and sound the

selected siren tone. Operate switch 8, or the foot

switch, again to deactivate Mode 3 and the SS2000

pursuit function.

Refer to the Installation and Operating Instruc-

tions supplied with the SS2000 for additional infor-

mation.

CAUTION

Improper warning system operation may re-

sult if the SS2000 Mode 3 switch is operated

when the SS2000 SmartSiren interface is

installed. Do not operate the SS2000 Mode 3

switch when the SS2000 SmartSiren interface

is installed.

1-6. KEYBOARD CONFIGURATIONS.

IMPORTANT

The control head’s LED display simulates the

light pattern(s) being executed by the warning

system. The display is intended ONLY as a

guide and NOT as an indication of proper

warning system operation.

Before using the warning system, its operation

should be observed from outside the vehicle.

The available “standard” keyboard configura-

tions are as follows:

• Keyboard Configuration 2 (POLICE A).

• Keyboard Configuration 3 (POLICE B).

• Keyboard Configuration 4 (FIRE A).

• Keyboard Configuration 5 (FIRE B).

• Keyboard Configuration 6 (RECOVERY).

• Keyboard Configuration 7 (CLEAR-

BOARD).

• Keyboard Configuration 8 (DEMO - sales

use only).

Determine which keyboard configuration is

selected. The installer or person responsible for

configuration will provide this information. Read and

understand the applicable keyboard configuration

description below.

1-3. LED ILLUMINATION INTENSITY ADJUSTMENT.

The bright LED’s provide maximum visibility in

high ambient lighting conditions. The RESET LED

illumination intensity can be adjusted from bright

illumination to dimmed, dimmer, or extinguished for

night operations. The backlighting illumination

intensity does not change, but does extinguish when

the RESET LED is extinguished.

To adjust, proceed as follows:

A. If any functions are activated, press the

RESET switch. The RESET LED should be illumi-

nated.

B. Press the RESET switch again to decrease

the LED illumination intensity.

C. Continue to press the RESET switch until

the desired LED illumination intensity and back-

lighting are achieved.

NOTE

Operating the foot switch (if installed), or

pressing any control head switch (except

RESET) will cause the LED illumination in-

tensity to revert to bright illumination.

Also, the LED illumination intensity will

revert to bright illumination when the vehicle

ignition switch, or user-supplied switch, is

switched “off” and switched “on”.

1-4. FOOT SWITCH.

Operating the optional foot switch will alternate

between the switch 8 function (usually Mode 3) and

the switch 7 function (usually Mode 2). If installed,

operate the foot switch to activate the switch 8

function. Operate the foot switch again to deactivate

the switch 8 function and activate the switch 7

function. Operating the foot switch a third time does

not deactivate the warning system; it will deactivate

the switch 7 function and reactivate the switch 8

function.

To deactivate a foot switch activated function,

operate the corresponding control head switch.

NOTE

Since the SS2000 SmartSiren® interface is

associated with the switch 8 function, the

siren will deactivate when the switch 7 func-

tion is activated.

1-3

A. Keyboard Configuration 2 (POLICE A).

NOTE

Refer to figure 1-1 while reading paragraph

1-6.A.

1. Switch 1 (RESET).

Press this switch to extinguish all

lights (if activated) in the lightbar. The RESET LED

will illuminate and the reflectors rotate to the “home”

position. All other LED’s will extinguish and acti-

vated functions will deactivate.

NOTE

The RESET switch may be pressed at any time

to deactivate any previously selected function(s).

2. Switch 2 (SignalMaster).

NOTE

This switch may be labeled “LRC-O” indicat-

ing—Left, Right, Center out, and Off.

Pressing this switch controls the

SignalMaster directional signal (if installed). It

provides a flashing arrow signal directing traffic to

move to the left, right, or around both sides of the

vehicle. In this keyboard configuration, the Signal-

Master switch utilizes “step through” activation.

Each press of switch 2 steps through the various

directional signals.

Switch 2 LED illuminates when the

SignalMaster is activated. Also, the row of LED’s

under the V-shaped display simulates the light

pattern being executed by the directional signal.

a. Press switch 2 to activate a left

arrow directional signal.

b. Press switch 2 a second time to

activate a right arrow signal.

c. Press switch 2 a third time to

activate a center out signal.

Figure 1-1. Keyboard Configuration 2.

d. Press switch 2 a fourth time to

deactivate the SignalMaster directional signal and

the switch 2 LED will extinguish.

3. Switch 3 (TAKE-DOWN).

Press switch 3 to activate the take-

down lights. The two lights fitted with clear domes

illuminate and rotate to the take-down (straight

ahead) position. Two LED’s in the V-shaped display

(which represent the take-down lights) will illumi-

nate and the switch 3 LED illuminates. Press switch

3 again to deactivate the take-down lights. The

LED’s in the V-shaped display and switch 3 LED will

extinguish. The take-down lights will return to the

previously activated function, if any.

NOTE

Take-down lights and alley lights can be aimed

or rotated horizontally. Refer to the descrip-

tions for the JOG LEFT and JOG RIGHT

switches below.

4. Switch 4 (RELAY A).

Press switch 4 to activate the auxiliary

device, such as headlight flashers or grille lights,

connected to the relay A output. The installer should

inform you what device (if any) is connected to the

relay A output. The switch 4 LED will illuminate.

Press switch 1 again to deactivate the auxiliary

device and extinguish the switch 4 LED.

5. Switch 5 (RELAY B).

Press switch 5 to activate the auxiliary

device connected to the relay B output. The installer

should inform you what device (if any) is connected to

the relay B output. The switch 5 LED will illuminate.

Press switch 5 again to deactivate the auxiliary

device and extinguish the switch 5 LED.

6. Switch 6 (MODE 1).

Press switch 6 to activate Mode 1. In

this keyboard configuration; a four-light, alternating,

oscillating pattern to the rear is activated. The LED’s

in the V-shaped display will flash indicating the

lights are activated and the switch 6 LED illumi-

nates. Press switch 6 again to deactivate Mode 1. The

LED’s in the V-shaped display and the switch 6 LED

will extinguish.

7. Switch 7 (MODE 2).

Press switch 7 to activate Mode 2. In

this keyboard configuration, four lights rotate at 90

FPM and three lights oscillate to the front. Also, the

auxiliary device (if any) connected to the relay C

output will activate. The installer should inform you

1-4

RESET 2 3 4 5 6 7 8

910 11

1 - Reset

2 - SignalMaster "step through"

3 - Takedown (pods 3 & 5)

4 - Relay A (push-on/push-off)

5 - Relay B (push-on/push-off)

6 - Mode 1 (pattern #42)

7 - Mode 2 (pattern #26 + Relay C)

8 - Mode 3 (pattern #27 + Relay C)

9 - Jog Left (pattern #86)

10 - Left Alley (pod 3 - pattern #76)

11 - Right Alley (pod 5 - pattern #73)

12 - Jog Right (pattern #87)

what device (if any) is connected to the relay C

output. The LED’s in the V-shaped display will flash

indicating the lights are activated and the switch 7

LED will illuminate. Press switch 7 again to deacti-

vate Mode 2. The LED’s in the V-shaped display and

the switch 7 LED will extinguish.

8. Switch 8 (MODE 3).

Press switch 8 to activate Mode 3. In

this keyboard configuration, all seven lights rotate in

synchronization at 90 FPM creating a center-out

pattern. The LED’s in the V-shaped display will flash

indicating the lights are activated and the switch 8

LED will illuminate. Press switch 8 again to deacti-

vate Mode 3. The LED’s in the V-shaped display and

the switch 8 LED will extinguish.

9. Switch 9 (JOG LEFT).

Press switch 9 to manually position

activated take-down/alley lights for use as a spot-

light. Each time switch 9 is pressed with a take-down

light activated, the light will move one step to the left

and the switch 9 LED will illuminate momentarily.

Each time switch 9 is pressed with the alley light(s)

activated, the light(s) will move one step to the rear

and the switch 9 LED will illuminate momentarily.

Press and hold switch 9 until the activated light(s)

rotates left or rear to the desired position.

NOTE

If switch 9 is pressed and held allowing the

activated take-down/alley light to rotate more

than approximately 1-1/2 revolutions, an error

indication will occur. Press switch 1 (RESET)

to clear the error indication and start over.

10. Switch 10 (LEFT ALLEY).

Press switch 10 to activate the left

alley light. The LED in the V-shaped display illumi-

nates to indicate which light is activated and the

switch 10 LED illuminates. Press switch 10 again to

deactivate the left alley light and extinguish the

switch 10 LED.

11. Switch 11 (RIGHT ALLEY).

Press switch 11 to activate the right

alley light. The LED in the V-shaped display illumi-

nates to indicate which light is activated and the

switch 11 LED illuminates. Press switch 11 again to

deactivate the right alley light and extinguish the

switch 11 LED.

12. Switch 12 (JOG RIGHT).

Press switch 12 to manually position

activated take-down/alley lights for use as a spot-

light. Each time switch 12 is pressed with a take-

down light activated, the light will move one step to

the right and the switch 12 LED will illuminate

momentarily. Each time switch 12 is pressed with

the alley light(s) activated, the light(s) will move one

step to the front and the switch 12 LED will illumi-

nate momentarily. Press and hold switch 12 until the

activated light(s) rotates right or forward to the

desired position.

NOTE

If switch 12 is pressed and held allowing the

activated take-down/alley light to rotate more

than approximately 1-1/2 revolutions, an error

indication will occur. Press switch 1 (RESET)

to clear the error indication and start over.

B. Keyboard Configuration 3 (POLICE B).

NOTE

Refer to figure 1-2 while reading paragraph

1-6.B.

1. Switch 1 (RESET).

Press this switch to extinguish all

lights (if activated) in the lightbar. The RESET LED

will illuminate and the reflectors rotate to the “home”

position. All other LED’s will extinguish and acti-

vated functions will deactivate.

NOTE

The RESET switch may be pressed at any time

to deactivate any previously selected function(s).

2. Switch 2 (JOG LEFT).

Press switch 2 to manually position

activated take-down lights for use as a spotlight.

Each time switch 2 is pressed, the activated lights

will move one step to the left and the switch 2 LED

will illuminate momentarily. Press and hold switch 2

until the activated lights rotate left to the desired

position.

1-5

Figure 1-2. Keyboard Configuration 3.

RESET 2 345678

910 1112

1 - Reset

2 - Jog Left (pattern #86)

3 - Takedown (pods 2 & 6)

4 - Jog Right (pattern #87)

5 - Relay A (push-on/push-off)

6 - Mode 1 (pattern #42)

7 - Mode 2 (pattern #26 + Relays B&C)

8 - Mode 3 (pattern #27 + Relays B&C)

9 - SignalMaster - Left

10 - SignalMaster - Center Out

11 - SignalMaster - Alternate

12 - SignalMaster - Right

NOTE

If switch 2 is pressed and held allowing the

activated take-down lights to rotate more

than approximately 1-1/2 revolutions, an error

indication will occur. Press switch 1 (RESET)

to clear the error indication and start over.

3. Switch 3 (TAKE-DOWN).

Press switch 3 to activate the take-

down lights. The two lights fitted with clear domes

illuminate and rotate to the take-down (straight

ahead) position. Two LED’s in the V-shaped display

(which represent the take-down lights) will illumi-

nate and the switch 3 LED illuminates. Press switch

3 again to deactivate the take-down lights. The

LED’s in the V-shaped display and switch 3 LED will

extinguish. The take-down lights will return to the

previously activated function, if any.

NOTE

Take-down lights can be aimed or rotated hori-

zontally. Refer to the switch operation descrip-

tions JOG LEFT (above) and JOG RIGHT

(below).

4. Switch 4 (JOG RIGHT).

Press switch 4 to manually position

activated take-down lights for use as a spotlight.

Each time switch 4 is pressed, the activated light will

move one step to the right and the switch 12 LED

will illuminate momentarily. Press and hold switch 4

until the activated light rotates right to the desired

position.

NOTE

If switch 4 is pressed and held allowing the

activated take-down lights to rotate more

than approximately 1-1/2 revolutions, an

error indication will occur. Press switch 1

(RESET) to clear the error indication and

start over.

5. Switch 5 (RELAY A).

Press switch 5 to activate the auxiliary

device, such as headlight flashers or grille lights,

connected to the relay A output. The installer should

inform you what device (if any) is connected to the

relay A output. The switch 5 LED will illuminate.

Press switch 5 again to deactivate the auxiliary

device and extinguish the switch 5 LED.

6. Switch 6 (MODE 1).

Press switch 6 to activate Mode 1. In

this keyboard configuration; a four-light, alternating,

oscillating pattern to the rear is activated. The LED’s

in the V-shaped display will flash indicating the

lights are activated and the switch 6 LED illumi-

nates. Press switch 6 again to deactivate Mode 1. The

LED’s in the V-shaped display and the switch 6 LED

will extinguish.

7. Switch 7 (MODE 2).

Press switch 7 to activate Mode 2. In

this keyboard configuration, four lights rotate at 90

FPM and three lights oscillate to the front. Also, the

auxiliary devices (if any) connected to the relay B and

C outputs will activate. The installer should inform

you what devices (if any) are connected to the relay B

and C outputs. The LED’s in the V-shaped display

will flash indicating the lights are activated and the

switch 7 LED will illuminate. Press switch 7 again to

deactivate Mode 2. The LED’s in the V-shaped

display and the switch 7 LED will extinguish.

8. Switch 8 (MODE 3).

Press switch 8 to activate Mode 3. In

this keyboard configuration, all seven lights rotate in

synchronization at 90 FPM creating a center-out

pattern. The LED’s in the V-shaped display will flash

indicating the lights are activated and the switch 8

LED will illuminate. Press switch 8 again to deacti-

vate Mode 3. The LED’s in the V-shaped display and

the switch 8 LED will extinguish.

9. Switch 9 (SignalMaster LEFT).

Press switch 9 to activate a left arrow

directional signal directing traffic around the left side

of the vehicle. The switch 9 LED illuminates and the

row of LED’s under the V-shaped display simulates

the light pattern being executed by the directional

signal. Press switch 9 again to deactivate the left

arrow directional signal and extinguish the switch 9

LED.

10. Switch 10 (SignalMaster CENTER

OUT).

Press switch 10 to activate a center out

directional signal directing traffic around both sides

of the vehicle. The switch 10 LED illuminates and

the row of LED’s under the V-shaped display simu-

lates the light pattern being executed by the direc-

tional signal. Press switch 10 again to deactivate the

center out directional signal and extinguish the

switch 10 LED.

1-6

11. Switch 11 (SignalMaster

ALTERNATE).

Press switch 11 to activate an alter-

nating flash pattern(four lamps in the center, then

two outer lamps on both sides). The switch 11 LED

illuminates and the row of LED’s under the V-shaped

display simulates the light pattern being executed by

the directional signal. Press switch 11 again to

deactivate the alternating flash pattern and extin-

guish the switch 11 LED.

12. Switch 12 (SignalMaster RIGHT).

Press switch 12 to activate a right

arrow directional signal directing traffic around the

right side of the vehicle. The switch 12 LED illumi-

nates and the row of LED’s under the V-shaped

display simulates the light pattern being executed by

the directional signal. Press switch 12 again to

deactivate the right arrow directional signal and

extinguish the switch 12 LED.

C. Keyboard Configuration 4 (FIRE A).

NOTE

Refer to figure 1-3 while reading paragraph

1-6.C.

1. Switch 1 (RESET).

Press this switch to extinguish all

lights (if activated) in the lightbar. The RESET LED

will illuminate and the reflectors rotate to the “home”

position. All other LED’s will extinguish and acti-

vated functions will deactivate.

NOTE

The RESET switch may be pressed at any time

to deactivate any previously selected function(s).

2. Switch 2 (Blank).

In this keyboard configuration, this

switch is not assigned a function. The installer/

programmer MUST inform you what function (if any)

is assigned to this switch.

Figure 1-3. Keyboard Configuration 4.

3. Switch 3 (RELAY A).

Press switch 3 to activate the auxiliary

device, such as headlight flashers or grille lights,

connected to the relay A output. The installer should

inform you what device (if any) is connected to the

relay A output. The switch 3 LED will illuminate.

Press switch 3 again to deactivate the auxiliary

device and extinguish the switch 3 LED.

4. Switch 4 (RELAY B).

Press switch 4 to activate the auxiliary

device connected to the relay B output. The installer

should inform you what device (if any) is connected to

the relay B output. The switch 4 LED will illuminate.

Press switch 4 again to deactivate the auxiliary

device and extinguish the switch 4 LED.

5. Switch 5 (RELAY C).

Press switch 5 to activate the auxiliary

device connected to the relay C output. The installer

should inform you what device (if any) is connected to

the relay C output. The switch 5 LED will illuminate.

Press switch 5 again to deactivate the auxiliary

device and extinguish the switch 5 LED.

6. Switch 6 (MODE 1).

Press switch 6 to activate Mode 1. In

this keyboard configuration; the center light oscil-

lates to the front, one light oscillates to the left, and

one light oscillates to the right. The LED’s in the V-

shaped display will flash indicating the lights are

activated and the switch 6 LED will illuminate. Press

switch 6 again to deactivate Mode 1. The LED’s in

the V-shaped display and the switch 6 LED will

extinguish.

7. Switch 7 (MODE 2).

Press switch 7 to activate Mode 2. In

this keyboard configuration, four lights rotate at 90

FPM and three lights oscillate to the front. The

LED’s in the V-shaped display will flash indicating

the lights are activated and the switch 7 LED will

illuminate. Press switch 7 again to deactivate Mode

2. The LED’s in the V-shaped display and the switch

7 LED will extinguish.

8. Switch 8 (MODE 3).

Press switch 8 to activate Mode 3. In

this keyboard configuration, all seven lights rotate in

synchronization at 90 FPM creating a center-out

pattern. The LED’s in the V-shaped display will flash

indicating the lights are activated and the switch 8

LED will illuminate. Press switch 8 again to deacti

1-7

RESET 2 345678

910 11

1 - Reset

2 - No function assigned

3 - Relay A (push-on/push-off)

4 - Relay B (push-on/push-off)

5 - Relay C (push-on/push-off)

6 - Mode 1 (pattern #48)

7 - Mode 2 (pattern #26)

8 - Mode 3 (pattern #27)

9 - V-Bar - Left (pattern #63)

10 - V-Bar - Center Out (pattern #64)

11 - V-Bar - Alternate (pattern #65)

12 - V-Bar - Right (pattern #62)

Other manuals for VISION

Table of contents

Other Federal Signal Corporation Security System manuals

Federal Signal Corporation

Federal Signal Corporation Global G-STR Series User manual

Federal Signal Corporation

Federal Signal Corporation PA300 Series 690009 Owner's manual

Federal Signal Corporation

Federal Signal Corporation PA300 Series 690009 Manual

Federal Signal Corporation

Federal Signal Corporation PA4000 Manual

Federal Signal Corporation

Federal Signal Corporation AV1ST Quick guide

Federal Signal Corporation

Federal Signal Corporation PSCE-R Manual

Federal Signal Corporation

Federal Signal Corporation Commander 371ST-250 Manual

Federal Signal Corporation

Federal Signal Corporation 400HMK-AC User manual

Federal Signal Corporation

Federal Signal Corporation 2-240 Manual

Federal Signal Corporation

Federal Signal Corporation 27XL-024-4 User manual

Federal Signal Corporation

Federal Signal Corporation CommCenter D1 Series Manual

Federal Signal Corporation

Federal Signal Corporation Split Vision VSLR3 User manual

Federal Signal Corporation

Federal Signal Corporation WV450XL Series User manual

Federal Signal Corporation

Federal Signal Corporation Vision SLR Series Manual

Federal Signal Corporation

Federal Signal Corporation CP-PB Series User manual

Federal Signal Corporation

Federal Signal Corporation Premium Vision Quick guide

Federal Signal Corporation

Federal Signal Corporation Informer-IP Wall Mount B Series User manual

Federal Signal Corporation

Federal Signal Corporation 400 Series User manual

Federal Signal Corporation

Federal Signal Corporation SLMBS Series User guide

Federal Signal Corporation

Federal Signal Corporation Global Series User manual

Federal Signal Corporation

Federal Signal Corporation 2001-130 User manual

Federal Signal Corporation

Federal Signal Corporation Pathway User manual

Federal Signal Corporation

Federal Signal Corporation SSTX3-MV Manual

Federal Signal Corporation

Federal Signal Corporation PA300 Series 690009 Quick guide

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual