Extech Instruments 42529 User manual

User’s Manual

InfraRed Thermometer

with Laser Pointer

MODEL 42529

Introduction

Congratulations on your purchase of the Model 42529 IR Thermometer. This thermometer

makes non-contact (infrared) temperature measurements at the touch of a button. The

built-in laser pointer increases target accuracy while the backlit LCD and handy push-

buttons combine for convenient, ergonomic operation. Proper use and care of this meter

will provide years of reliable service.

Model 42529-EU V2.0 5/09

Safety

Use extreme caution when the laser pointer beam is on

Do not point the beam toward anyone's eye or allow the

beam to strike the eye from a reflective surface

Do not use the laser near explosive gases or in other

potentially explosive areas

Specifications

Infrared Thermometer Specifications

Range / Resolution -20 to 320oC (0 to 600oF) 1oC/F

Accuracy ± 2% of reading or ± 2oC (4oF) whichever is greater.

Note: Accuracy is specified for the following ambient

temperature range: 18 to 28°C (64 to 82°F)

Emissivity 0.95 fixed value

Field of View D/S = Approx. 6:1 ratio (D = distance, S = spot)

Laser power Less than 1mW

Spectral response 6 to 14 m (wavelength)

General Specifications

Display 3½ digit backlit LCD display with function indicators

Display rate 1 second approx.

Over range indication Audible tone sounds and ‘OVER’ appears on the LCD when

the measurement exceeds the measurement range spec.

Operating Temperature 0°C to 50°C (32°F to 122°F)

Operating Humidity Max. 80% RH.

Power Supply 9V battery

Automatic Power Off Meter shuts off automatically after 7 seconds

Weight 180g / 6.35 oz.

Size 211 x 89 x 38mm (8.3 x 3.5 x 1.5”)

Meter Description

1. LCD Display

2. Function Buttons

3. Handle Grip

4. Laser Pointer

5. IR Sensor

6. Measurement Trigger

7. Battery Compartment

Model 42529-EU V2.0 5/09

Operating Instructions

1. Hold the meter by its Handle Grip and point it toward the device whose temperature is

to be measured.

2. Press and hold the red Trigger to turn the meter on and begin testing. The display will

light if the battery is charged. Replace the battery if the display does not light.

3. While continuing to press the Trigger, push the red Laser button to turn on the laser

pointer. Aim the red beam approximately a half inch higher than the point of test as

shown in the diagram below (pressing the Laser button again turns the laser off).

4. While measuring, the SCAN display icon will appear on the LCD above the

temperature measurement and to the left of the emissivity value (fixed at 0.95.).

5. If the measurement exceeds the useable temperature range (0 to 600oF), the meter will

emit a tone and the LCD will display ‘OVER’.

6. Release the Trigger when the temperature stabilizes. The HOLD display icon will

appear on the LCD indicating that the reading is being held.

7. Set the temperature units (oC or oF) using the blue oCand oFbuttons.

8. Press the yellow Backlight key to turn on the LCD backlighting function.

9. The meter will automatically power down after 7 seconds.

Field of View

The meter’s field of view is 6:1. For example, if the meter is 30.4cm from the target (spot),

the diameter of the target must be at least 5.08cm. Other distances are shown below in the

field of view diagram.

Note that measurements should normally be made less than 60.9cm from the target. The

meter can measure from further distances but the measurement may be affected by

external sources of light. In addition, the spot size may be so large that it encompasses

surface areas not intended to be measured.

Model 42529-EU V2.0 5/09

Measurement Notes

1. The object under test should be larger than the spot (target) size calculated by the field

of view diagram (see diagram on previous page or on side of the meter).

2. If the surface of the object under test is covered with frost, oil, grime, etc., clean before

taking measurements.

3. If an object's surface is highly reflective apply masking tape or flat black paint before

measuring.

4. The meter cannot measure through transparent surfaces such as glass.

5. Steam, dust, smoke, etc. can obscure accurate measurements.

6. The meter compensates for deviations in ambient temperature. It can, however, take

up to 30 minutes for the meter to adjust to extremely wide ambient temperature

changes.

7. To find a hot spot, aim the meter outside the area of interest then scan across (in an up

and down motion) until the hot spot is located.

Battery Replacement

When the low battery symbol appears on the LCD, replace the meter’s 9V battery.

The battery compartment is located on the bottom of the meter's handle. Open the

compartment by sliding the battery compartment cover off in the direction of the arrow.

Replace battery and re-install the battery compartment cover.

You, as the end user, are legally bound (Battery ordinance) to return all used

batteries and accumulators; disposal in the household garbage is prohibited!

You can hand over your used batteries / accumulators at collection points in your

community or wherever batteries / accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the

device at the end of its lifecycle

Other Extech Instruments Thermometer manuals

Extech Instruments

Extech Instruments 42570 User manual

Extech Instruments

Extech Instruments SL250W User manual

Extech Instruments

Extech Instruments IRT25 User manual

Extech Instruments

Extech Instruments RH200W User manual

Extech Instruments

Extech Instruments 42520 User manual

Extech Instruments

Extech Instruments 42510A User manual

Extech Instruments

Extech Instruments SD200 User manual

Extech Instruments

Extech Instruments TM55 User manual

Extech Instruments

Extech Instruments IR260 User manual

Extech Instruments

Extech Instruments IR255 User manual

Extech Instruments

Extech Instruments 39240 User manual

Extech Instruments

Extech Instruments HD550 User manual

Extech Instruments

Extech Instruments IR100 User manual

Extech Instruments

Extech Instruments 445703 User manual

Extech Instruments

Extech Instruments IR400 User manual

Extech Instruments

Extech Instruments 42535 User manual

Extech Instruments

Extech Instruments TM20 User manual

Extech Instruments

Extech Instruments IR270 User manual

Extech Instruments

Extech Instruments RH490-NIST User manual

Extech Instruments

Extech Instruments SD500 User manual

Extech Instruments

Extech Instruments IR200 User manual

Extech Instruments

Extech Instruments K.J.E.T. 422324 User manual

Extech Instruments

Extech Instruments RH200W User manual

Extech Instruments

Extech Instruments IR250 User manual

Popular Thermometer manuals by other brands

Delton

Delton 981A instruction manual

Baker

Baker MM2P instruction manual

Tarmo

Tarmo 320281 manual

Citizen

Citizen CTD 504 instruction manual

TFA

TFA 14.1500 instruction manual

Vive

Vive DMD1010 user manual

Gotemp

Gotemp THB4002 user guide

GREISINGER

GREISINGER G 1202 Quick reference guide

Amprobe

Amprobe TMD-53W user manual

Trotec

Trotec BP10 operating manual

Radiance instruments

Radiance instruments RT616 Series product manual

Eurolec

Eurolec IR151 operating instructions

Scaneo

Scaneo TS42B instruction manual

Sper scientific

Sper scientific 800043 instruction manual

Microlife

Microlife NC 200 Operating instructions manual

Motorola

Motorola MBP69SN General questions

The MeatStick

The MeatStick The MeatStick quick start guide

Hama

Hama TH35-A operating instructions