Extech Instruments PRC10 User manual
USER GUIDE
Current Calibrator
Model PRC10
Extech PRC10 Current Calibrator Meter
Extech PRC15 Current and Voltage Calibrator Meter
Extech PRC20 Multi Thermocouple Calibrator
Extech PRC30 Multifunction Process Calibrator
actoolsupply.com
actoolsupply.com
actoolsupply.com
2PRC10-EU-EN-V1.2 01.13
Introduction
Thank you for selecting the Extech Model PRC10. This device is shipped fully tested and calibrated
and, with proper use, will provide years of reliable service. Extech Instruments is an ISO-9001
certified company.
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the
manual for further information.
This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages
may be present
Double insulation
Safety Notes
Do not exceed the maximum allowable input range.
Turn the unit OFF when the device is not in use.
Remove the batteries if the device is to be stored for longer than 60 days.
Never dispose of batteries in a fire. Batteries may explode or leak.
Never mix battery types. Always install new batteries of the same type.
Cautions
Improper use of this meter can cause damage, shock, injury or death. Read and understand
this user manual before operating the meter.
Always remove the test leads before replacing the battery.
Inspect the condition of the test leads and the meter itself for any damage before operating the
meter. Repair or replace any damage before use.
If the equipment is used in a manner not specified by the manufacturer, the protection provided
by the equipment may be impaired.
actoolsupply.com
actoolsupply.com
3PRC10-EU-EN-V1.2 01.13
Meter Description
1. AC adaptor input jack
2. Display
3. Power
ON/OFF
4. Source output adjustment arrow buttons
5. Set
button
6. Unit button (mA or %)
7. I/O MODE button
8. MEM (memory STEP button)
9. Backlight/ZERO
button
10. Test lead inputs
Display Layout
1. SOURCE mode icon
2. ZERO function status icon
3. MEASURE mode icon
4. Loop Power icon
5. Auto Power OFF active icon
6. Battery status icon
7. Measure mode value
8. Measure mode units icon
9. Datalogger memory location
10. Source mode value
11. Source mode units icon
3
4
5
6
7
8
10
9
2
1
actoolsupply.com
actoolsupply.com
4PRC10-EU-EN-V1.2 01.13
Keypad Descriptions and Operation
POWER BUTTON and AUTO POWER OFF FEATURE
1. Use the POWER button to turn the unit ON or OFF. When the unit is powered up, a short
self-test will ensue after which the display will stabilize.
2. When the battery symbol flashes on the display, replace the battery as soon as possible.
Low battery power may cause inaccurate readings and erratic meter operation.
3. This instrument is equipped with Auto Power OFF which turns the meter off after 10 minutes
of inactivity. To override this feature; press and hold the POWER button until the display
icon “ATP” turns off.
UNIT BUTTON
Press the UNIT button to select mA or %units.
I/O BUTTON
Momentarily press the I/O button to select either SOURCE (output) or MEASURE (input).
MODE BUTTON (Loop Power)
In the MEASURE mode, Press and Hold the MODE (I/O) button for 1seconds to turn loop power on
or off.
(Backlight) BUTTON
Momentarily press the Backlight button to turn the backlight on or off.
ZERO ( ) BUTTON
In the MEASURE or SOURCE mode, Press and Hold the ZERO ( ) button for 1seconds to zero
the meter.
► ◄ ▼and ▲BUTTONS
The arrow buttons are used to set the output value in the SOURCE mode.
1. Select the SOURCE mode
2. Press the ►or ◄button select a digit for adjustment. The blinking underline curser
identifies the digit selected.
3. Press the ▼or ▲button to adjust the value of the digit. Press and Hold the ▼or ▲button to
rapidly adjust the value.
actoolsupply.com
actoolsupply.com
5PRC10-EU-EN-V1.2 01.13
SET BUTTON
The SET button is used to manually step through the 5 stored output values.
1. Select the SOURCE mode
2. Press the SET button and the value stored in memory location 01 will be sourced. “MEM.01”
appears in the display.
3. Each press of the SET button will step through the 5 memory locations.
4. The arrow buttons can be used to adjust the value in each memory location.
STEP/MEM BUTTON
The STEP/MEM button is used to automatically step through the 5 stored output values. The meter
can be set for a single cycle of the stored values or a continuous cycle.
1. Select the SOURCE mode
2. Press and HOLD the STEP/MEM button. ”STEPSS” (single cycle) and “STEPSC”
(continuous cycle) will alternately appear in the display. Release the button when the
desired mode is displayed.
3. In single cycle mode the meter will source the current displayed in MEM01 for 5 seconds.
The meter will then advance to MEM02 for 5 seconds. This will continue through MEM05
and then step down through the memory locations. The cycle will end when MEM01 has
been reached.
4. In the continuous mode the cycle will continue until manually stopped.
5. Momentarily press the STEP/MEM button to stop the cycle. “END” will briefly appear in the
display.
STORING VALUES INTO MEMORY
The default values stored in the memory locations are:
Memory
Location mA %
M1 4.00mA 0.0%
M2 8.00mA 25%
M3 12.00mA 50%
M4 16.00mA 75%
M5 20.00mA 100%
To change the values in memory:
1. Select the SOURCE mode
2. Press the SET button to select the memory location to be changed.
3. Press the arrow buttons to adjust to the new value
4. Momentarily press the MEM button to store the value. The memory location icon will blink
while the value is being stored.
actoolsupply.com
actoolsupply.com
6PRC10-EU-EN-V1.2 01.13
Modes of Operation
MEASURE (Input) Mode of Operation
In this mode, the unit will measure up to 50mADC.
1. Turn the meter ON.
2. “MEASURE” will appear in the display.
3. Press the UNIT button to select mA or %
4. Press and HOLD the “MODE-I/O” button for 2 seconds if 24V loop power is required.
“Lp.POWER” will appear in the display.
5. Connect the Calibration Cable to the meter.
6. Connect the Calibration Cable to the device or circuit under test.
7. Read the measurement on the LCD display.
SOURCE (Output) Mode of Operation
In this mode, the unit can source current up to 24mADC at 1000 ohms. The current can be output
either manually or stepped from memory as described earlier.
1. Turn the meter ON
2. Press the “I/O” button to select SOURCE.
3. Use the UNIT button to select %or mA.
4. Connect the Calibration Cable to the meter
5. Connect the Calibration Cable to the device or circuit under test
6. Use
the
arrow buttons to set the desired output value in the lower display. The upper
display indicates the actual current value being sourced. If the upper display does not match
the set value, either the batteries need to be replaced or the load impedance is beyond the
specified range.
actoolsupply.com
actoolsupply.com
7PRC10-EU-EN-V1.2 01.13
Tilt Stand / Hanger
The rear stand is provides two methods for convenience in viewing.
1. Pull the bottom portion of the stand out to place the unit on a flat surface for viewing.
2. Pull the bottom and top portions of the stand out, and then rotate the stand to allow the unit to
be hung.
Battery Replacement
When the battery icon appears on the display, the six AA batteries must be replaced.
The battery compartment is located on the rear of the meter.
1. Open the tilt stand, loosen the captive Philips head screw and remove the battery cover.
2. Remove and replace the batteries, observing polarity.
3. Replace and secure the battery cover.
All EU users are legally bound by the Battery Ordinance to return all used batteries to
community collection points or wherever batteries / accumulators are sold.
Disposal in household trash or refuse is prohibited.
Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the
end of its lifecycle
Battery Safety Reminders
Please dispose of batteries responsibly; always observe local, state, and federal regulations
with regard to battery disposal.
Never dispose of batteries in a fire. Batteries may explode or leak.
Never mix battery types or old and new batteries. Always install new batteries of the same
type.
actoolsupply.com
actoolsupply.com
8PRC10-EU-EN-V1.2 01.13
Specifications
General Specifications
Display Dot matrix LCD
Maximum Load 1000 ohms @ 24mA
Meter Power 6 AA batteries or AC adaptor
Auto Power OFF Meter automatically powers off after 10 minutes of inactivity
Current output capability 24mADC at 1000 ohms
Operating Temperature 41ºF to 104ºF (5ºC to 40ºC)
Storage Temperature - 4oF to 140oF (-20oC to 60oC)
Operating Humidity Max 80% up to 87ºF (31ºC) decreasing linearly to 50% at 104ºF
(40ºC)
Storage Humidity <80%
Operating Altitude 7000ft (2000meters) maximum
Dimensions 159 x 80 x 44 mm (6.3 x 3.2 x 1.7")
Weight 232g (8.2 oz.) without batteries
Range Specifications
Mode Function Range (Resolution) Accuracy (% of reading)
Current 0 to 50mA (0.01mA)Measure
Percent (%) -25% to +230% (0.1%)
Current 0 to 24mA (0.01mA)Source
Percent (%) -25% to +125% (0.1%)
± (0.01% + 1 digit)
Power Loop Power 24 to 30VDC, <50mA
actoolsupply.com
actoolsupply.com
Table of contents
Other Extech Instruments Test Equipment manuals
Extech Instruments
Extech Instruments 380260 User manual
Extech Instruments
Extech Instruments 380320 User manual
Extech Instruments
Extech Instruments ExStik PH150-C User manual
Extech Instruments
Extech Instruments HDV700 User manual
Extech Instruments
Extech Instruments 412300A User manual
Extech Instruments
Extech Instruments PRC15 User manual
Extech Instruments
Extech Instruments CB10 User manual
Extech Instruments
Extech Instruments ET60 User manual
Extech Instruments
Extech Instruments ExStik CL200 User manual
Extech Instruments
Extech Instruments prc20 User manual
Extech Instruments
Extech Instruments 382357-NIST User manual
Extech Instruments
Extech Instruments 382252 User manual
Extech Instruments
Extech Instruments MG320 User manual
Extech Instruments
Extech Instruments MS6100 User manual
Extech Instruments
Extech Instruments 407744 User manual
Extech Instruments
Extech Instruments ET25 User manual
Extech Instruments
Extech Instruments GX930 User manual
Extech Instruments
Extech Instruments 412300 User manual
Extech Instruments
Extech Instruments 480303 User manual
Extech Instruments
Extech Instruments 480303 User manual
