EverFocus EHD525EX User manual
EHD525EX
1/3”
Color
Rugged
Dome
True
Day/Night
Camera
1/3” Color Rugged Dome True Day/Night Camera
with
EXView
Sensor
with EXView Sensor
User’s Manual
and
Operation Instructions
Notice
This manual is presented to the users of EHD525EX series by EverFocus
Electronics Corp. With years of engineering researches, EverFocus has
spared no effort to provide the high quality products to the worldwide users.
For the policy of continual product improvement, EverFocus reserves the
right to make changes to the product specifications and documentation
without notice. All the components of the products, including accessories,
components, and outlook, are based on the agreements of each deal to satisfy
all kinds of users. Meanwhile, please be advised that every step of operation
must follow the instruction of this manual to keep EHD525EX series working
under the best condition. Please notice that EverFocus will not be charged
any claims or renewing cases resulted from inappropriate operation.
Table of Contents
Safety Warning ……………………………………. 1
Introduction………………………………………... 2
Specifications………………………………………..3
Installation Instructions…………………………… 4
Dip Switch Functions……………………………… 11
Simple Instructions for the Desiccant Pack……… 13
Safet
y
Warnin
g
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TVs, radio transmitters, magnets,
electric motors, transformers, and audio speakers as the magnetic
fields generated from these devices will distort the video image.
2. Do not install the camera in a high temperature environment.
Install camera away from stoves or other heat generating devices
as the high temperature could cause deformation, discoloration or
other damage to the camera. Install the camera where the
temperature range will stay between -40 ~ 122 degree Fahrenheit.
3. Never face the camera towards the sun.
Never aim the camera at the sun or other extremely bright objects
whether it is in use or not.
4. Cleaning
Do not touch the surface of CCD sensor by hand directly. Use a
soft cloth to remove the dirt from the camera body. Use lens tissue
or a cotton tipped applicator and ethanol to clean the CCD sensor
and the camera lens. When the camera is not in use, put the cover
cap on the lens mount.
5. Heater
Heater elements can be very hot! Heaters are located inside the
camera housing and will activate automatically while the
environment temperature is below 50 degrees Fahrenheit. Do not
touch the heater element while it’s active.
1
Introduction
The most technically advanced EHD series are the newest vandal-resistant
Color Rugged Dome Camera from EverFocus Electronics. The Color Rugged
Dome Camera can withstand a blow from a 10-pound sledgehammer and has a
built-in heater that allows for operation in low temperatures. It is perfect for
all high-profile crime-prone applications such as building entrances, retail
stores, and shopping malls. The extremely durable EHDseries are
unquestionably one of the world's toughest cameras and is your best choice for
vandal resistance. The EHD525EX is designed with True Day/Night function
that allows removable Auto IR Cut and an enhanced B/W sensitivity, while
turning the image from color to B/W.
Main Features for EHD525EX:
zHigh sensitivity designed with 2nd generation SONY EXView sensor.
zSensitivity increases more than 40% compared to other high resolution
sensors
zRevolutionary integrated 10-bit Digital Signal Processor (DSP)
delivers excellent picture quality and performance.
zLow light sensitivity of 0.1 lux/F=1.2 is achieved by using the
advanced 1/3” interline transfer color EXView CCD.
zThe electronic shutter and AGC allow the camera to be used in
environment with varying light levels.
zDC 12V or AC 24V switches automatically power supply; Line Lock
for AC 24V.
zS/N Ratio reaches 52 dB or more.
zIR Vari-focal lens with IR Cut Removable module available.
zTrue Day & Night function.
zCompact size: 5.1” (W) x 3.9” (H) x 5.1” (D).
zZinc base; polycarbonate shell withstand the impact of 10 pounds
sledgehammer, smoke color or clear cover as option.
zUnique security screw lock.
zOperating temperature: -40 ~ 122 degrees Fahrenheit.
zHeater triggered when temperature is less than 50 degree Fahrenheit.
2
S
p
ecifications
Model: EHD525EX
Pickup device: SONY 1/3” interline transfer color EXView CCD
Picture element: NTSC: 768(H) × 494(V)
PAL: 752(H) × 582(V)
Horizontal Resolution: 520 TV Lines
Sensitivity: 0.1 lux / F=1.2
S/N ratio: >52dB(AGC off)
Vari-Focal Lens: 3.6-9mm / 9-22mm IR Lens
IR Cut Removable: Yes (Auto IR Cut Removable and B/W Sensitivity
Enhanced)
Weatherproof Ratings: IP66
Electronic shutter: Up to 1/100,000
IRIS Control: Auto
Auto white balance: YES
Auto gain control: ON/OFF switch
Back light comp.: ON/OFF switch
Line Lock: ON/OFF switch for 24VAC
Flickerless: ON/OFF switch
Gamma correction: 0.45
Video output: 1.0Vp-p, 75ohm
Power source: 12V DC+/-10%, 24VAC+/-10%
Power Consumption: 5W Max. (15W when heater active;
thermostatically controlled)
Sync. mode: Internal Sync. /Line lock (Only for AC24V)
Dimension: 5.1” (W) x 3.9” (H) x 5.1” (D).
Heater auto activated
temperature: 50 degree Fahrenheit
Operating temperature: -40 ~ 122 degrees Fahrenheit, 20~80%
Weight: 3.7 lbs
3
Installation Instructions
1. Loosen the 4 fix screws on the housing cover by using the provided
wrench (Figure 1). Carefully uncap the housing cover as the direction
shown below (Figure 2); please pay attention not to damage the lens. To
remove the housing cover, push the hinges to the bottom of the bracket,
the hinges can be easily removed from the bracket.
Figure 1
Figure 2
2. Remove the camera.
Vari-Focal Lens
Locking Screws
Heater
Figure 3
To remove the camera, first unplug the wire connection on the back of
the camera. Then loosen the 2 locking screws on the camera base, push
the camera base to the right (toward heater direction, as shown in Figure
3), remove the camera from the mounting base. Reinstall the camera and
the cable while the base mounting is completed.
4
3. Mounting the base.
Attach the base to the wall or ceiling; fix the base by the 4 setscrews
provided in the accessory pack. The dome weight is approximately 3.7 lbs,
please make sure if the mounting is strong enough to support the weight.
If not, please reinforce the mounting according to the environment.
Note: The diameter of the screw hole is 4.7mm.
Caution: To prevent moisture leaking into the housing, apply an
appropriate gasket or sealant around the conduit connection.
Conduit plug setscrew
Side conduit entry
Back conduit entry
Mounting Setscrew
Mounting Setscrew
Mounting Setscrew
Mounting Setscrew
Figure 4
The camera comes with a conduit plug
pre-installed in the PF 1/2 conduit entry
on the side. The screw can be removed
and installed in the back conduit entry.
Loosen the conduit plug setscrew (as
shown in Figure 5) before removing the
conduit plug.
Side conduit entry (PF1/2)
Figure 5
Back conduit entry (PF1/2)
Conduit plug
5
4. Re-assemble Camera
I. When mounting COLOR RUGGED DOME CAMERA on the
wall, please aim the “Wall” in line with the triangle “S” marked
on the lead frame. (Factory default)
II. When mounting COLOR RUGGED DOME CAMERA on the
ceiling, please aim the “Ceiling” in line with the triangle “S”
marked on the lead frame.
“Wall”
Figure 6-1
6
“Ceiling”
Figure 6-2
6
5. Wire Connection
Connect the power supply cable (AC24V/DC12V), video output and
alarm output to the proper connectors shown as Figure 7.
The V. Phase adjustment screw is located on the termination board.
The vertical phase may require adjustment to synchronize the vertical
phase of the camera with other cameras in the system when it is to be used
in the line-lock sync mode. Make sure the vertical phase adjustment of
the camera does not match other cameras.
Note: The inner part of power plug is positive. The pigtail wire with the white
stripe is positive.
Termination Board
7
Micro Switch for Alarm trigger
Video
Alarm COM GND
Alarm NO Alarm NC
Power In (+)
Power In (-)
V. Phase Adjustment VR
Figure 7
7
Other manuals for EHD525EX
1
Table of contents
Other EverFocus Security Camera manuals
EverFocus
EverFocus EHD700A Ultra User manual
EverFocus
EverFocus EDH5201 User manual
EverFocus
EverFocus ED335 User manual
EverFocus
EverFocus EHD935F eZ.HD Series User manual
EverFocus
EverFocus EQ200E User manual
EverFocus
EverFocus EZH5102 User manual
EverFocus
EverFocus EQH5102 User manual
EverFocus
EverFocus EZN3160 User manual
EverFocus
EverFocus EHD300/N-2 User manual
EverFocus
EverFocus EHD935 eZ.HD Series User manual
EverFocus
EverFocus M099-VDE101-002 User manual
EverFocus
EverFocus EBA2880 User manual
EverFocus
EverFocus M116-EZ700-001 User manual
EverFocus
EverFocus EQ700 User manual
EverFocus
EverFocus ED710 Owner's manual
EverFocus
EverFocus EAN600 User manual
EverFocus
EverFocus EB200 User manual
EverFocus
EverFocus EDH5240 User manual
EverFocus
EverFocus eZ Tracker EFN3320 User manual
EverFocus
EverFocus EPTZ100 User manual
