EverFocus ED300 Series User manual
ED300 Series
User’s Manual
and
Operation Instructions
Version 1.1
Notice
This manual is presentED300 to the users of ED300 by EverFocus Electronics Corp.
With years of engineering researches, EverFocus has sparED300 all efforts to
provide the high quality products to the worldwide users. For the policy of
continual product improvement, EverFocus reserves the right to make changes to the
product specifications and documentation without notice. All the components of
the products, including accessories, components, and outlook, are bas ED300 on the
agreements of each deals to satisfy all kinds of users. Please be advis ED300 that
every step of operation must follow the instruction of this manual to keep ED300
working under the best condition. Please notice that EverFocus will not be
chargED300 any claims or renewing cases resultED300 from inappropriate
operation.
Table of Contents
Safety Warning...............................................................................1
Introduction....................................................................................3
Specification...................................................................................4
Major Parts Names and Functions...........................................5
Installation Instructions ............................................................7
Lens Adjustments.......................................................................8
Adjustments................................................................................9
Safety Warning
1. Do not expose the camera to humidity and dust.
Moisture can damage the camera and cause the danger of electric shock.
If the camera is mountED300 outdoors, a camera housing is
requirED300. Do not install the camera at where there is greasy smoke
or steam, where the humidity is too high, or where there is a lot of dust
to prevent damages to the camera.
2. Do not disassemble the camera.
Do not disassemble the camera body as it is dangerous and may cause
the damages to the camera. Refer all servicing to qualifiED300 service
personnel.
3. Handle the camera with care.
Be careful when handling the camera, do not drop it or subject it too
strong shock or vibration to prevent any damages to it.
4. Do not install the camera near electric or magnetic fields.
InstallED300 the camera away from TV, radio transmitter, magnet,
electric motor, transformer, audio speakers because the magnetic fields
generate from above devices will distort the video image.
1.
5. Do not install the camera in the high temperature environment.
InstallED300 the camera away from stoves, or other heat generating
devices, or where it could be subject to direct sunlight as the high
temperatures could cause deformation, discoloration or other damages of
the camera. Install the camera at where the temperature range will stay
between 0℃to 50℃(32℉to 122℉).
6. Cleaning
Use a soft cloth to remove the dirt from the unit. Use lens tissue or a
cotton tippED300 applicator and ethanol to clean the camera lens.
2.
Introduction
The High Resolution Dome Camera Series are compact, full
functionED300 CCD Color Cameras. Their stylish appearance can be
appliED300 as per installer's ideal locations on the ceiling. The dome
camera designED300 with advancED300 digital processing curcuitry for
high resolution 1/3" color interline transfer CCD sensor, it has DIP switch
for AGC on/off, BLC on/off. The dome camera uses a vari focal auto iris
lens for discreet surveillance or close-up viewing and it features with iris
LEVEL volume control for the best viewing quality.
Main Features:
??DesignED300 with advancED300 digital signal processing circuitry for high
image quality.
??The high sensitivity of 1.42 lux / F=1.6is achievED300 by high-resolution 1/3”
Interline transfer CCD.
??Built-in Vari Focal type, mechanical auto iris lens
??Able to adjust the viewing range with manual zoom lens. c
??With manual PAN/TILT mechanism.
??BLC and AGC function on/off switchable.
??Compact size : 108mm O.D. x 80mm H.
??System available for NTSC or PAL
3.
Specification
Pickup device: 1/3" Interline transfer CCD
Video format: NTSC/PAL
Scanning system: NTSC: 525 TV lines, 60 fields/sec; PAL: 625 TV lines, 50 fields/sec.
Picture elements: NTSC: 811(H) x 508 (V); PAL: 795 (H) x 596 (V)
Effective picture elements:
NTSC: 768 (H) x 494 (V); PAL: 752 (H) x 582 (V)
Horizontal resolution: 480 TV lines
Sensitivity: 1.42 lux / F=1.6
S/N ratio: > 48 Db
Varifocal lens: manual zoom and focus adjustment, mechanical auto IRIS
IRIS level: Adjustable
Back light comp.: On / Off Switch
Auto Gain Control: On / Off Switch
Auto white balance: Yes
Gamma correction: 0.45
Monitor output pin: Yes, 1.0 Vp-p / 75 ohm, test point pin
Video output: 1.0Vp-p/75ohm
Sync. mode: Internal sync.
Audio Available for model High Resolution Dome A
Power source 12VDC or 24VAC, 300mA
Dimension: 108 mm O.D. x 80 mm H
Operating temperature: 0oC to +50oC/20~80%
Power consumption: 5W max.
4.
Major Parts Names and Functions
《ED300》《ED300-A》
?
?
?
11
?
?
?
?
?
?
?
12
5.
?
12
13
?Camera Cover
This cover will protect the camera from dust
and damage.
?Lens
This Vari-
Focal Lens allows users to adjust
the Zoom and Focus manually.
?Base
The c
amera unit is set in the dome base when
it is shippED300 from the factory.
?Focus Ring
To set the focus, loosen the Focus ring knob
first, then turn the ring toward <∞
> or <N>
as necessary. When the focus is
obtainED300 as desirED300, tighten the
focus ring knob.
?Zoom Ring
Loosen the zoom ring knob, then you can
adjust the viewing range. Turn the ring
towards <W> for WIDE or <T> for TELE as
necessary. When the setting is
finishED300, tighten the zoom ring knob.
?Auto Gain Control on/off switch.
The factory setting is AGC on.
?Back Light Compensation on/off
switch
The factory setting is BLC off.
?Level Volume Control
The iris level control for the lens.
?Ground Pin
For monitor use. Please see ?.
?Monitor Pin
When setting up the camera,
connect a
monitor to this video output pin and to the
GROUND pin using alligator clip cables, then
using the image displayED300 on the monitor,
set the surveillance angle.
Power input
Use the connector to connect with 12VDC
or 24VAC-power adaptor.
Video Output BNC Connector
Use the connector to connect with the video in
connector of a monitor.
11
13
6.
12
Installation Instructions
1. Remove the plastic dome cover.
2. Lossen the two screws of the supporting bracket to remove the camera
body.
3. Using four screws to fix the camera base on the ceiling.
4. Put the camera body back to the supporting bracket, then tighten the two
screws to fix the camera.
5. Connect the BNC connector of the camera to a color monitor, or other
video device through a 75 ohm type coaxial cable with BNC female
connector at cable extension.
6. Connect the DC+12V or 24VAC regulatED300 power source of the
camera (DC Jack) to the DC12V or 24VAC Power-in jack with 2mm,
center+, outer-plug.
7. Connect the audio output connector of the camera(model High
Resolution Dome A) to the audio in connector of the monitor.
NOTE: Be very careful not to scratch or damage the lens while making any kind
of setting.
7.
Other manuals for ED300 Series
3
Table of contents
Other EverFocus Security Camera manuals
EverFocus
EverFocus ECMD100i Technical manual
EverFocus
EverFocus eZ Tracker EFN3320 User manual
EverFocus
EverFocus EQ150 User manual
EverFocus
EverFocus 380TVL, 520TVL User manual
EverFocus
EverFocus EHA2580 eZ.HD Series User manual
EverFocus
EverFocus EPTZ3000 User manual
EverFocus
EverFocus EZ350 User manual
EverFocus
EverFocus EZ350 User manual
EverFocus
EverFocus eZ.HD Series User manual
EverFocus
EverFocus ED610 User manual
EverFocus
EverFocus EQ610x User manual
EverFocus
EverFocus 1/3" B/W CCD Camera None User manual
EverFocus
EverFocus EBD331e User manual
EverFocus
EverFocus EB100 User manual
EverFocus
EverFocus EPTZ3602 User manual
EverFocus
EverFocus ED200 Series User manual
EverFocus
EverFocus EQH5102 User manual
EverFocus
EverFocus Indoor Pendent Dome Camera EPD200 User manual
EverFocus
EverFocus Speed Dome EPTZ3100I User manual
EverFocus
EverFocus ED350 User manual
