Erreka CICLON Operating instructions

CICLON

Quick installation and programming guide English

WARNING

This quick guide is a summary of the complete installation manual. The manual contains safety warnings and

other explanations which must be taken into account. The installation manual can be downloaded by going

to the "Downloads" section of Erreka website:

http://www.erreka.com/Automatismos/descargaDocumentos.aspx

*4 x 1mm2

(max. 20m)

E246A

4 x 0,5mm2

(max. 30m)

2 x 0,75mm2

(max. 20m)

3 x 1,5mm2

(max. 30m)

2 x 0,5mm2

(max. 20m)

2 x 0,5mm2

(max. 20m)

RG-58/U

2 x 0,5mm2

(max. 30m)

Elements of the complete installation

Electrical wiring

A: Main power supply

B: LUMI flashing light

C: Photocells (Rx/Tx)

D: Pushbutton/key switch

E: Operator *:

motor: 4x1mm2

brake: 2x1mm2

encoder: shielded cable 2x0.5mm2

F: LUMI built-in antenna

G: Electrolock

VERY IMPORTANT:

The TC closing limit switch must be

installed in all cases, and TA opening limit

switches whenever the articulated arm is

installed.

The electrolock is obligatory for operators without

lock (CL210 and CL250). For operators with lock, the

electrolock must be used for gate leaf lengths of over

1.8m.

*NOTE: the electrical installation of the operator can be

done correctly and straightforwardly using the cable with

AYCY8 code, which ERREKA can supply by metre. This

cable has the characteristics 4x1mm2+2x1mm2+

((2x0.5mm2)) and was developed specifically for this use.

In dual leaf facilities without brake or

encoder, the following should be taken into

account when programming the operations:

when programming the closing of leaf 2 and the

leaf reaches the closing limit switch, wait for a

time equal to the lapse between leaves before

pressing ST1 to end programming. This ensures

that, during the closing operation, leaf 2 remains

at the closing limit switch during lapse until leaf

1 closes completely.

MST-041/00

D246A D246B

Unlocked (only for models with brake)

Unlocked for manual operation:

•Remove the cap and insert the key (1).

•Turn the key 90° anti-clockwise (A). The gate is

free to move manually.

Lock for motorised operation:

•Turn the key (1) 90° clockwise (B).

•Remove the key and position the cap to stop

water from coming in.

500mm

100mm

M246C

100mm

548mm

N32901

580mm

360mm

M246B

548mm

435 mm

N32001

410mm

340mm

M246A

100mm

(80mm)

548mm

(600mm)

500mm

(1000mm)

ACL16/ N32501

610mm

(990mm)

120 mm

Assembly levels

Assembly with sliding arm ACL16/

N32501 (inward opening)

The TC closing limit switch must be

installed with this type of arm.

The levels with no brackets

correspond to models

CLS210F/

CL210F (T2000VFI)/ CL210 with arm

N32501.

The levels between brackets

correspond to models CLS250F/

CL250F/ CL250 with arm ACL16.

Assembly with sliding arm

N32901 (outward opening)

The TC closing limit switch must be

installed with this type of arm.

The exterior opening arm is only

valid for the operators CLS210F/

CL210F (T2000VFI)/ CL210.

Assembly with articulated arm

N32001 (inward opening)

TC closing limit switch and TA

opening limit switch must be installed

with this type of arm.

The N32001 articulated arm is

only valid for the models CLS210F/

CL210F (T2000VFI)/ CL210.

P246E

P246D

P246F

P246H

Assembly

B1 Mount the drag wheel (1) on the operator shaft.

B2 Install the arm (2) and the cap (3) on the drag

wheel.

Close the gate, pull the arm (1) a maximum of

670 mm and mark the positions A and B

. Secure

the bracket (2) in this position.

1 Mount the operator (1) on the bracket (2) using the

screws and washers supplied (3).

Then mount the unit on the wall

Remember that the bracket corresponding to models

CLS210F/ CL210F (T2000VFI) / CL210 is shown.

The bracket for models CLS250F/ CL250F/ CL250 has

some differences, although assembly is carried out in a

similar way.

P246A

A1 Mount the drag wheel (1) on the

operator shaft.

A2 Install the arm (2) and the cap (3)

on the drag wheel.

A3 Close the gate and mark position A

on it.

Open the gate and mark position B

on it.

Secure the track so points A and B

are aligned inside.

A4 Position the closing and opening

limit switches (1) on the track using

the plate (2) (the opening limit

switch is shown in the figure).

P246G

OPTION A: assembly with sliding arm

OPTION B: assembly with articulated arm

P246Z

ENCODER1 ENCODER2

P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23

GND

V+

NG1

NG2

GND

V+

NG1

NG2

-FT

(Test)

AUX

24 Vdc

FT1

P1 P2 P3

FT2

P4 P5 P6

TOP

P7 P8

WARNING

LIGHT

P10

24V

P11

P12

LOCK

Lamp.

G9 G10

G7 G8

Courtesy

Light

G1 G2 G3

MOTOR1

G4 G5 G6

MOTOR2

CN13

POWER - 230V

P24 P25

EDGE

FT1

P1 P2 P3

FT2

P4 P5 P6

TOP

P7 P8

WARNING

LIGHT

P10

24V

P11

P12

LOCK

ST1

V+

GND

SGN1

POWER - 230V

VIVO-M203:

230V, 50Hz

VIVO-M203M:

125V, 60Hz

ST2

EPS1

Electrical connections, control board VIVO-M203

M1 and M2 motor connection:

G4/G1: brown cable

G5/G2: black cable

G6/G3: grey cable

C: capacitor; CL210 / CL210F (T2000VFI) / CLS210F: 5μF; CL250/ CL250F/ CLS250F: 8μF

Encoder connection (if available):

V+: red cable

GND: mesh

SGN1: blue cable

Check the control board instructions to connect the other

components and carry out programming.

EPS1

COM

FR2

FR1

P246Y

M203: 230V/50Hz

Brake cabling by way of EPS1 (VIVO-M203, parameter Ab01)

DL1: Red LED, FR1 activation

DL2: Green LED, FR2 activation

COM: orange cable (models with encoder)

white cable (models without encoder)

L1, L2: purple cable (models with encoder)

red cable (models without encoder)

Other manuals for CICLON

Other Erreka Gate Opener manuals

Erreka

Erreka KAIROS User manual

Erreka

Erreka CICLON Series User manual

Erreka

Erreka AMO02 User manual

Erreka

Erreka TEMIS User manual

Erreka

Erreka MAGIC User guide

Erreka

Erreka DINGO Operating instructions

Erreka

Erreka VULCAN User guide

Erreka

Erreka SIRIUS Operating instructions

Erreka

Erreka ARES Series User guide

Erreka

Erreka DINGO User manual

Erreka

Erreka PUMA-I Operating instructions

Erreka

Erreka NAOS Operating instructions

Erreka

Erreka CICLON Series Operating instructions

Erreka

Erreka VULCAN D User manual

Erreka

Erreka TORO KM1800 Operating instructions

Erreka

Erreka TOPO User guide

Erreka

Erreka DINGO Operating instructions

Erreka

Erreka VULCAN D VUA12 User guide

Erreka

Erreka CICLON User guide

Erreka

Erreka MAGIC Operating instructions

Erreka

Erreka Puma User guide

Erreka

Erreka AXIL Series User manual

Erreka

Erreka CALYPSO Series User manual

Erreka

Erreka ARES User guide

Popular Gate Opener manuals by other brands

Elite

Elite CSW200UL instruction manual

CAME

CAME FROG-PM4 installation manual

SOMFY

SOMFY FX230 installation manual

Aprimatic

Aprimatic ONDA 500 installation instructions

Turnstiles

Turnstiles FSW 900 manual

Beninca

Beninca R1-2 WBV quick start guide

Motorline professional

Motorline professional FORT User& installer's manual

Beninca

Beninca BOB5024 manual

AGA

AGA GATEMASTER 900 HD installation manual

Chamberlain

Chamberlain MotorLift HC280ML Mechanical installation

SOMFY

SOMFY Dexxo RTS Pro INSTALLATION INSTRUCTIONS-ILLUSTRATIONS

Cardin

Cardin BL Series manual

Westfalia

Westfalia 85 27 06 instruction manual

CAME

CAME F500 installation manual

Extel

Extel VERA quick guide

Comunello Automation

Comunello Automation ABACUS 220 Installation and user manual

CAME

CAME FA40230CB installation manual

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES installation manual