Erreka PUMA-I Operating instructions

PUMA-I

Quick installation and programming guide English

WARNING

This quick guide is a summary of the complete installation manual. The manual contains safety warnings and

other explanations which must be taken into account. The installation manual can be downloaded by going

to the "Downloads" section of Erreka website:

http://www.erreka-automation.com

D268A

D268B

E268C

Assembly levels (mm) Unlocking

Locking for operation

motorised:

•Turn the handle (2) anti-clockwise 270°

without forcing it.

•Turn the key (1) anti-clockwise and remove.

•Push the cylinder (3) inward and manually

move the gate to interlock it in the operator

mechanism

E268D

Electrical wiring

A: Main power supply

B/E: Flashing light/Antenna

C: Photocells (Tx / Rx)

D: Pushbutton/wall key

Elements of the complete installation

Unlocking Locking

Unlocking for manual

operation:

•Insert the key (1) and

turn clockwise without

forcing it.

•Turn the handle (2)

clockwise 270°,

through to the stopper

but without forcing it.

WARNING: The PUMA-I

operator is supplied

without a capacitor for the

motor, since the control

board's Inverter

technology makes it

unnecessary. If this board

is used to replace another

operator, do not use a

capacitor for the motor.

R.E.

(ST1)

(ST2)

(DIP6=OFF: FCA)

(DIP6=ON: FCC)

FC1

(DIP6=OFF: FCC

(DIP6=ON: FCA)

FC2

P268Y

DL1 DL2 DL3

ST1

ST2

SW1

DL6

F1-0,315A

SW2

F5-3A F6-0,5A

ST1

FT1

ST2

FT2

+12 GND

STOP LAMP

G2 G1 C N L

MOTOR POWER

(FT1)

SG. A (FT2)

RADIO

RECEIVER

DL21

DL8

Waiting

Time

POT2

DL11 DL

DL9

DL10

(12Vdc)

DL26

General connections

DIP6=OFF DIP6=ON

Check and configure turning direction and limit switches

Encoder (DIP7): for the correct operation of the encoder, ensure DIP7 is in ON. The operation needs to be

reprogrammed if the encoder is disabled.

Check that DL21 flashes during gate movement.

‹A capacitor should not be used for the motor with the PUMA-I

operator fitted with Inverter technology control board.

DL1 Automatic closing LED

DL2 Radio programming LED

DL3 Travel programming LED

DL6 FT2 photocell LED

DL7 FC1 limit switch LED

DL8 FC2 limit switch LED

DL9 FT1 photocell LED

DL10 ST2 pushbutton LED

DL11 ST1 pushbutton LED

DL21 Encoder LED

DL26 DC Bus LED

‹

Motor with

no capacitor

Turning direction: check operation using ST1 and ST2 mini-pushbuttons with DIP1=ON. If turning direction is not as

indicated for position DIP6, interchange the wires connected to the G1 and G2 terminals.

PEDESTRIAN

TOTAL

E268L

SW1

SW1 Functions during programming (DIP1=ON)

DIP1=ON: programming enabled (DL3 lights up); ST1: open, ST2: close

DIP1=ON and DIP2=ON: total open/close programming

DIP1=ON and DIP3=ON: pedestrian open/close programming

DIP1=ON and DIP4=ON: total opening radio code programming

DIP1=ON and DIP6=ON: pedestrian opening radio code programming

Total opening radio code programming (with RSD receiver only)

1 Connect the power supply and

close the gate with DIP1 in ON

position and keeping ST2 pressed

down.

2 Select the code in the transmitter. 3 Place the DIPs as shown in the

figure (DIP1=ON, DIP4=ON). DL3

lights up to show programming

mode enabled.

R268A

ST2

R268C

R268B

SW1

Press the button of the required channel

DL2 flashes when programming is complete

5 Place DIP1 and DIP4 in OFF.

DL3 remains off.

6 Disconnect and reconnect the

electrical power supply.

Programming is carried out in the

same way, using DIP6 instead of DIP4.

R268D

R268E

SW1

Pedestrian opening radio

code

ZIf a receiver other than RSD is used, see the corresponding instructions.

Total open/close programming

Connect the power supply and close

the gate with DIP1 in ON position

and keeping ST2 pressed down.

2 Place the DIPs as shown in the

figure (DIP2=ON, DIP1=ON).

DL3 lights up to show

programming mode enabled.

R268A

ST2

G268Z

SW1

3 Press ST1 to start opening. 4 Press ST1 to start slowdown. 5 Wait for it to come to a stop at the

end of travel.

G268A

ST1

G268B

ST1

6 Press ST1 to start closing. 7 Press ST1 to start slowdown. 8 Wait for it to come to a stop at the

end of travel.

G268D

ST1

G268E

ST1

9 Place DIP1 and DIP2 in OFF. DL3

remains off.

R268E

SW1

Pedestrian open/close programming

This is carried out in the same way as total travel

programming, with the following differences:

•DIP1 and DIP3 are used instead of DIP1 and DIP2

•ST2 is used instead of ST1

•In step 5, stop the gate with ST2

DIP Modes and functions Option Effect

DIP1 OFF

DIP2 Advance warning

ON the flashing light comes on and the operation begins after a 3

second warning

OFF the flashing light comes on and the operation begins

immediately

DIP3 Opening mode

ON step-by-step opening (the gate halts if a key command is

activated during opening, and closes if activated again)

OFF collective opening (the control board does not obey the key

commands during opening)

DIP4 Automatic or step-by-step mode

(for pedestrian and total operation)

ON automatic mode (the gate closes automatically after standby

time has passed, which is adjusted using T.E.). A key command

(or photocell activation) causes standby time to restart

OFF step-by-step mode (the gate only closes when receiving the key

command)

DIP5 Automatic mode optional

(only if DIP4 = ON)

ON during standby, the gate obeys the key commands (can be

closed before standby time finishes)

OFF the gate cannot be closed until standby time finishes; a key

command will cause standby time to restart

DIP6 Gate movement

direction

ON gate which opens to the left

OFF gate which opens to the right

DIP7 Encoder ON encoder enabled

OFF encoder disabled

DIP8 Slowdown ON the gate reduces its speed before reaching the stopper

OFF the gate reaches the stopper at high speed

Function and mode selection using SW1 (DIP1 = OFF)

T.E (Standby Time): gate open standby time

If automatic functioning mode has been programmed

(DIP4=ON), set T.E. to adjust standby time with the gate

open (before automatic closing begins).

•Minimum value: 0 seconds; maximum value: 90

seconds

P.M (Torque Regulator): motor torque

Use P.M. to adjust the maximum motor power value.

‹Adjust the torque to respect the maximum closing

thrusts set out in Standard EN12453:2000. Make

the measurements as described in Standard EN

12445:2000.

Waiting

Time

POT2

P268M

Potentiometer adjustment

Other manuals for PUMA-I

Other Erreka Gate Opener manuals

Erreka

Erreka ARC Series User guide

Erreka

Erreka AXIL Operating instructions

Erreka

Erreka CICLON Operating instructions

Erreka

Erreka VULCAN S User manual

Erreka

Erreka MAGIC User guide

Erreka

Erreka TORO KM1800 Operating instructions

Erreka

Erreka KAIROS MSB-027/01 User manual

Erreka

Erreka Dolfin Operating instructions

Erreka

Erreka TEMIS User manual

Erreka

Erreka MAGIC User guide

Erreka

Erreka TOPO User guide

Erreka

Erreka MAGIC Operating instructions

Erreka

Erreka MAGIC Operating instructions

Erreka

Erreka BUL BL33 Operating instructions

Erreka

Erreka CAT Operating instructions

Erreka

Erreka ARES Series User guide

Erreka

Erreka Puma Operating instructions

Erreka

Erreka VIVO-M201 Operating instructions

Erreka

Erreka KAIROS User manual

Erreka

Erreka LINCE Operating instructions

Erreka

Erreka VIVO-M101 Operating instructions

Erreka

Erreka DINGO Operating instructions

Erreka

Erreka VULCAN D VUA12 User guide

Erreka

Erreka HERA Technical document

Popular Gate Opener manuals by other brands

Elite

Elite CSW200UL instruction manual

CAME

CAME FROG-PM4 installation manual

SOMFY

SOMFY FX230 installation manual

Aprimatic

Aprimatic ONDA 500 installation instructions

Turnstiles

Turnstiles FSW 900 manual

Beninca

Beninca R1-2 WBV quick start guide

Motorline professional

Motorline professional FORT User& installer's manual

Beninca

Beninca BOB5024 manual

AGA

AGA GATEMASTER 900 HD installation manual

Chamberlain

Chamberlain MotorLift HC280ML Mechanical installation

SOMFY

SOMFY Dexxo RTS Pro INSTALLATION INSTRUCTIONS-ILLUSTRATIONS

Cardin

Cardin BL Series manual

Westfalia

Westfalia 85 27 06 instruction manual

CAME

CAME F500 installation manual

Extel

Extel VERA quick guide

Comunello Automation

Comunello Automation ABACUS 220 Installation and user manual

CAME

CAME FA40230CB installation manual

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES installation manual