Erreka TEMIS User manual

E F

TC H

TEMIS

Quick Installation Guide MSB-026/04

WARNING

Elements of the complete installation

150

160

170

180

190

150 160 170 180 190

200

210

200 210140

140

>120° 110°~120°

100°~110°

90°~100°

BD Aprox

TATA

This quick guide is a summary of the complete installation manual. The manual contains safety warnings and

other explanations which must be taken into account. The installation manual can be downloaded by going

to the "Downloads" section of Erreka website:

http://www.erreka-automation.com

Electrical Wiring

A.B: 24v DC Motor(2x1mm²)

C: Photocell 2x0.5mm² (max 20m)

D: Control Box (3x1.5mm²)

E: Push Botton 2x0.5mm²(max 25m)

Assembly levels, inward opening

TEMIS It is not applicable to an insecure or lacking rigidity door nor solves the defects due to incorrect installation or mainte-

Check the following points before starting the installation:

1). Hinges are properly positioned and greased.

2). No obstacles in the moving area and no frictions between two gate leafs or with the ground while moving.

3). “C” value is 139mm.

4). “D” can be measured from the gateeasily.

5). “A” = “C” + “D”

6). The value of “B” can be calculated from the value of “A” and the leaves opening angle.

Ex. If “A”=160mm with the leaves opening angle of 100 degrees, then the value of “B” is approximate 190mm.

Please make sure B and A are similar or the same in value that the leaves can be

operated smoothly, also to reduce the burden of the motor.

Open Interior

F: Key Selector(2x0.5 mm²)

G: Flash Light (2x0.5mm²)

H.I: Electric Lock (2x1mm²)

TA: Open Stopper

TC: Closed Stopper

Assembly

Unlocking

Unlocking for manual operation: Motorised operation locking:

1 2

Place the two brackets on the surface and the

position where they will be installed, please make

sure that the front bracket is installed completely

horizontally.

Place the motor on rear bracket with screw (A) and nut (B).

1 1

1. Insert the key to the release slot.

2. Turn counterclockwise to release the motor.

1. Insert the key and turn clockwise .

2. Remove the key.

Assembly levels, outward opening

Please make sure B and A are similar or the same in value that the leaves can be operated smoothly, also to

reduce the burden of the motor.

Open exterior

3 4

Release the gate opener with the door in closed

position. Place the front bracket without xing it..

Check the door manually which can be moved easily in

entire route.

Horizontal 180O

Technical Feature

Dimensions

Max gate length

Max gate weight

Power supply

Motor power supply

Gear Type

Peak Thrust

Normal Thrust

Operation Stroke

Piston extention

Opening Time

Duty Cycle

Protection Grade (IP)

Operation temperature

Absorbed current (A)

Absorbed Power (W)

Manual Release

Enclosure Dimensions

2.2M

200kg

110V/230VAC (50-60Hz) SMART-D201M / SMART-D201

24VDC

Worm and worm gear

2200N

1500N

400mm

19.8mm/sec

<20 sec

20%

IP44

-20

C~+50

4.2A for 10 sec

60W

Key

803mm*100.5mm*185mm

Block the motor and make the electrical wiring to connect the cables M1 and M2 correctly. If you only

install one gate, connect the wires to the terminal M1.

100mm

100.5mm

185mm

803mm

765mm

ADC

BDAprox

Motor 1 Motor 2

(+)

(-)

(+)

(-)

Electrical connections

Flash Light 24Vdc

Electric Lock 24Vdc

Key

Selector Push

Botton

Transformer

Antenna

TX1 TX2

FT1 FT2

RX1 RX2 Green Box

M2-M1-

Lat-

Lit- Lmt4Lmt3

Lmt2

Lit+ SKey

M2+

M1+Lat+ Ph2Ph1 PhVcc PhVcc

S25V

ANT

GND

DKey GND

GND GND GND

Lmt1 GND

Q17

K2K1

J4 J3

DB1

NC NO

+--+

NONC

NC NO

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

LED3

LED4

LED2

LED Display

LED1 System Learning

LED2 RF Learing

LED3 Photocell 1

LED4 Photocell 2

SET

DOWN

RF-LEARN

Batteries recharger incorporated in control board, no need to connect extra recharger.

Maximum batteries capacity connection is up to 15Ah.

The battery housing on the box is prepared for 2 batteries of 1.3 Ah.

Batteries connection

Display indications

Operation for Function settings

For example: How to set the Function “F1-2”; the steps are following:

(1) Press the “SET” button for 3seconds, the LED will display F1.

(*) To enter “F2” Function or another Functions, press the “UP”

button to adjust F2 ~ F8.

Step Operations LED Display after the Step

(2) After completing the operation (1) then press the “SET” button

again, you will enter the second option.

(3) Continually, press “UP” button until you search the Function “2”

(**) of F1 as the right hand-side picture. “F1-2” is set completely.

(**) If you would like to set one of Function “0 ~ 8” as the second

option, please press “UP” or “DOWN” button to adjust it.

(4) If you would continue setting up the next Functions, press “SET”

to return the first option, like F1, F2, F3.....etc.

For example, after complete F1-2 setting. You would continue

setting F2-2, please press “SET” to return the formal option. The

LED display shows the first two numbers as the first option F1. And

then follow the operation (*) and (2) ~ (3) until complete the setting.

After setting all Functions you need, then wait for 10 seconds, the

LED will display “RUN”. And you can use transmitter to operate the

gate.

LED Display Programmable Functions

“N-L”: The system learning is not done.

“RUN”: The system is in normal

performing.

“CLN” the memory of the system is all

cleaned/deleted. Press “UP+DOWN”

for 5 seconds.

“STP”: the motor stop in the middle of

the operating process.

“ARN”: The system learning is in

progress.

“ME”: Motor operation error.

“LEA”: Enter learning mode and then

wait for learning instructions.

The operation of gate learging:

(1). Press “SET” + “DOWN” + “UP”

for 3 seconds, and the LED display shows

“LEA” +”DG”; and then press the

transmitter A botton one time. After

1~3seconds, the LED display shows the

current value during learning mode, it

shows 10 for 1A

Open/close programming

Gate-moving Logic

(A) In gate-opening phase: the gates stop if the transmitter/push button/key selector is activated, and close when

you press the button again.

(B) In gate-closing phase: the gates stop if the transmitter/push button/key selector is activated, and open when you

press the button again.

Step1: Set the Function F2-1 for double leaf gate learn; or set the Function F2-2 for single leaf gate learning.

Step2: Press and hold the “UP+SET+DOWN” for 3 seconds. LED show “LEA D-G”.

Step3: Press A button on the transmitter for double leaf gate system learning or B button for single gate.

In system learning mode, the gates will proceed with the following procedures:

$'RXEOH/HDYH*DWH'*0&ORVHĺ0&ORVHĺ02SHQĺ02SHQĺ0&ORVHĺ0&ORVH

%6LQJOH/HDI*DWH6*0&ORVHĺ02SHQĺ0&ORVH

Advise: If change the configuration of F2, you should program the system learning again.

The completion of system learning:

(A) For Double leaf gate (D-G) installation: Show RUN on LED display

(B) For Single leaf gate (S-G) installation: Show RUN on LED display.

Notes:

(A) System learning fails and needs to be learned again when an unpredictable interruption occurs.

In this case, please make sure the Function F3 is in F3-1.

(B) Once the system learning is completed, there is no need to proceed with the learning process again when

there is a power failure.

Radio code programming

Radio code deleting

1 2 3

Press and hold the RF-Learn button on the PCB for 10 seconds until

blue LED off.

Blue LED ON

1 s 5 s 5 s

RF-Learn

Press and hold the RF-Learn for 1

second, the blue LED on the RF board

will be ON.

Press A button for 5 seconds for double leaf

gate Radio code programming installation.

Press B button for 5 seconds for single-gate

installation.

10 s

LED Display

¡ ATTENTION ! The 24Vdc ﬂash light output is not ﬁxed output but ﬂashing. To connect a ﬁxed or a ﬁxed mode ﬂash

light for the proper Function.

NOTE (Parameter F9)

Exterior Photocell: Only be activated in case of door closing.

Interior Photocell: Can be activated in door opening and door closing..

Complete programming chart (1)

Encoder/ Limit switch

Number of operators

Maximum trapping force

Gate speed

Slowdown

Soft stop speed

Lapse between leaves in

opening and closing

Semi-automatic or

automatic

operation mode and

stand-by

time (in seconds) in

automatic

mode

Photocell Function mode

(Open-close,

interior-exterior)

Pedestrian opening

Flashing light pre-warning

F1-1

F1-2

F1-3

F2-1

F2-2

F3-1

F3-2

F3-3

F3-4

F4-1

F4-2

F5-1

F5-2

F6-1

F6-2

F7-1

F7-2

F7-3

F7-4

F7-5

F7-6

F7-7

F7-8

F7-9

F8-0

F8-1

F8-2

F8-3

F8-4

F8-5

F8-6

F8-7

F8-8

F9-1

F9-2

F9-3

F9-4

FA-0

FA-1

FB-0

FB-1

Motor only

Motor with limit switch

Motor with encoder

Two Operators

One Operator

100% Full Speed

80% Full Speed

Function ON

Function OFF

70% Full Speed

50% Full Speed

F6-3

35% Full Speed

F6-4

25% Full Speed

2 sec.

3 sec.

4 sec.

5 sec.

6 sec.

7 sec.

8 sec.

9 sec.

10 sec.

OFF

3 sec.

10 sec.

20 sec.

40 sec.

60 sec.

120 sec.

180 sec.

300 sec.

Mode 1

Mode 2

Mode 3

Mode 4

OFF

1. The factory setting is "F1-1".

1. The factory setting is "F2-1".

1. The factory setting is "F3-1".

2. Please make sure that the parameter F3 is always in F3-1

in case of system learning process.

1. The factory setting is "F4-1".

1. The factory setting is "F5-1".

1. The factory setting is "F6-2".

1. The factory setting is "F7-1".

1. The factory setting is "F8-0".

1. The factory setting is "F9-1".

Mode 1: Photocell Exterior FT1- Photocell Interior FT2

Mode 2: Photocell Exterior FT1- Safety Belt FT2

Mode3: Photocell Exterior FT1- Open Device FT2

Mode 4: Photocell Interlock FT1- Fotocélula Interior FT2

1. When Function on and push B key in the transmitter, one

gate will open partically.

2. The factory setting is "FA-0".

1. When Function ON, the light will ﬂash before the gate

operate 3 seconds. If set OFF, the ﬂash light will operate

with motor in the same time.

2. The factory setting is "FB-0".

LED Display Deﬁnition Parameter Mode Description

Complete programming chart (2)

Note (Parameter F3)

Please set F3 Function after system learning. The LED display 10 to indicate all of the recorded values will increase 1 ampere as

the over current value. In other words, the LED shows 20 to indicate all the recorded values will increase 2 ampere as the over

current value. The value can be adjusted by pressing button UP and DOWN. The maximum value is 40(4.0A) and the minimum

value is 05 (0.5A)

LED Display Deﬁnition Parameter Mode Description

Photocell1

Photocell2

Buzzer Function

Reverse Impulse for

Electric Lock

Open/Stop/Close/Stop

Function key

Pedestrian Mode Function

key

Auto-Close Function key

FC-0

FC-1

FD-0

FD-1

FE-0

FE-1

FF-0

FF-1

FG-1

FG-2

FG-3

FG-4

FH-0

FH-1

FH-2

FH-3

FH-4

FI-0

FI-1

FI-2

FI-3

FI-4

OFF

A key

B key

C key

D key

OFF

A key

B key

C key

D key

OFF

A key

B key

C key

D key

1. The factory setting is "FC-0".

1. The factory setting is "FD-0".

1. The factory setting is "FE-0".

1. if the Function is on, the gate will move forward a

little before the gate operate for releasing the Latch

2. The factory setting is "FF-1".

1. The factory setting is "FG-1".

1. The factory setting is "FH-2".

1. The key is to turn on or off the Auto-Close Function.

2. The factory setting is "FI-0".

3. When the ﬂasher and buzzer is running, the auto

closed button has no Function till ﬂasher and buzzer

ﬁnish running.

Table of contents

Other Erreka Gate Opener manuals

Erreka

Erreka TORO KM1800 Operating instructions

Erreka

Erreka IZAR User guide

Erreka

Erreka PUMA-I Operating instructions

Erreka

Erreka Dolfin Operating instructions

Erreka

Erreka JEDI JES100E User manual

Erreka

Erreka VULCAN D User manual

Erreka

Erreka PUMA-I Operating instructions

Erreka

Erreka CICLON Series User manual

Erreka

Erreka AXIL Operating instructions

Erreka

Erreka VIVO-M101 Operating instructions

Erreka

Erreka HERA Technical document

Erreka

Erreka KAIROS User manual

Erreka

Erreka DINGO Operating instructions

Erreka

Erreka VIVO-M201 Operating instructions

Erreka

Erreka KAIROS MSB-027/01 User manual

Erreka

Erreka VIVO-D102 Operating instructions

Erreka

Erreka BUL BL33 Operating instructions

Erreka

Erreka CICLON Operating instructions

Erreka

Erreka Fenix User guide

Erreka

Erreka VULCAN S User manual

Erreka

Erreka TOPO User guide

Erreka

Erreka VULCAN D VUA12 User guide

Erreka

Erreka TORO KM1800 Operating instructions

Erreka

Erreka ARES User guide

Popular Gate Opener manuals by other brands

Elite

Elite CSW200UL instruction manual

CAME

CAME FROG-PM4 installation manual

SOMFY

SOMFY FX230 installation manual

Aprimatic

Aprimatic ONDA 500 installation instructions

Turnstiles

Turnstiles FSW 900 manual

Beninca

Beninca R1-2 WBV quick start guide

Motorline professional

Motorline professional FORT User& installer's manual

Beninca

Beninca BOB5024 manual

AGA

AGA GATEMASTER 900 HD installation manual

Chamberlain

Chamberlain MotorLift HC280ML Mechanical installation

SOMFY

SOMFY Dexxo RTS Pro INSTALLATION INSTRUCTIONS-ILLUSTRATIONS

Cardin

Cardin BL Series manual

Westfalia

Westfalia 85 27 06 instruction manual

CAME

CAME F500 installation manual

Extel

Extel VERA quick guide

Comunello Automation

Comunello Automation ABACUS 220 Installation and user manual

CAME

CAME FA40230CB installation manual

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES installation manual