Ericsson HM210dp User manual
ADSL Modem HM210dp/di - User Guide
© Ericsson AB 2003
All rights reserved
ADSL Modem HM210dp/di
User Guide
2 (98) EN/LZT 108 6492 R1
April 2003
Copyright
This manual is published by Ericsson AB, without any warranty. Improvements and changes to this manual necessitated by
typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by
Ericsson AB at any time and without notice. Such changes will, however, be incorporated into new editions of this manual.
All rights reserved.
© Ericsson AB 2003
EN/LZT 108 6492 R1 3 (98)
April 2003
Contents page
1 Introduction 6
1.1 Features 6
1.2 Package Contents 6
1.3 System Requirements 6
2 Hardware Description and Connection 8
2.1 Front Panel and LED Indicators 8
2.2 Back Panel and Connectors 9
2.3 Placement 9
2.4 Connecting the Hardware 10
3 Local PC Configuration 11
3.1 Configuring your PCs as DHCP Clients 11
3.1.1 In Windows 95, 98 and Me 11
3.1.2 In Windows 2000 and XP 11
3.2 Assigning Static IP Information to your PCs 12
4 Getting Started with the Configuration Manager 13
4.1 Accessing the Configuration Manager 13
4.2 Commonly Used Buttons and Icons 15
4.3 Committing Changes to Permanent Storage 16
4.3.1 Rebooting the HM210dp/di using the Configuration Manager 17
4.4 Quick Configuration 18
5 Basic Configuration 20
5.1 Bridge Mode 20
5.1.1 Configuring the HM210dp/di 20
5.1.2 Check Your Connection Status 24
5.1.3 Configuring the PC 24
5.2 PPP Connection Mode 25
5.2.1 Configuring the HM210dp/di 25
5.2.2 Check Your Connection Status 28
5.2.3 Configuring the PC 28
5.3 Router Connection Mode 28
5.3.1 Configuring the HM210dp/di 28
5.3.2 Check Your Connection Status 31
5.3.3 Configuring the PC 31
6 Configuring IP Routes 32
6.1 Viewing the IP Routing Table 32
6.2 Adding IP Routes 33
7 DHCP Configuration 34
4 (98) EN/LZT 108 6492 R1
April 2003
7.1 HM210dp/di DHCP Modes 34
7.2 Configuring DHCP Server 34
7.2.1 Creating IP Address Pools 34
7.2.2 Enabling DHCP Server Mode 36
7.2.3 Configuring Your PCs as DHCP Clients 36
7.2.4 Modifying IP Address Pools 36
7.2.5 Viewing Current DHCP Address Assignments 37
7.3 Configuring DHCP Relay 37
7.3.1 Defining the DHCP Relay Interface(s) 37
7.3.2 Enabling DHCP Relay Mode 38
7.3.3 Configuring Your PCs as DHCP Clients 38
8 NAT Configuration 39
8.1 Default NAT Setup 39
8.2 Viewing NAT Configuration 39
8.3 Viewing NAT Rules and Rule Statistics 41
8.4 Viewing Current NAT Translations 42
8.5 Adding NAT Rules 43
8.5.1 The NAPT Rule 44
8.5.2 The RDR Rule 45
8.5.3 The BASIC Rule 46
8.5.4 The FILTER Rule 47
8.5.5 The BIMAP Rule 49
8.5.6 The PASS Rule 50
9 DNS Configuration 51
9.1 DNS Relay Overview 51
9.2 Configuring DNS Relay 51
10 RIP Configuration 54
10.1 Configuring the RIP 54
10.2 Viewing RIP Statistics 56
11 Firewall Configuration 57
11.1 Global Firewall Settings 57
11.2 IP Filter Configuration 60
11.2.1 Viewing Your IP Filter Configuration 60
11.2.2 Configuring IP Filter Global Settings 60
11.2.3 Creating IP Filter Rules 61
11.2.4 Viewing IP Filter Statistics 67
11.2.5 Managing Current IP Filter Sessions 67
11.3 To Block Specific Protocols 68
12 Administration Tasks 70
12.1 Changing the System Date and Time 70
12.2 Adding Login User ID and Changing Login Password 71
EN/LZT 108 6492 R1 5 (98)
April 2003
12.3 Image Upgrade 72
12.4 Diagnostics 74
12.5 Port Settings 75
12.6 View System Alarms 76
13 View DSL Parameters 77
14 Troubleshooting 80
14.1 LEDs 81
14.2 Internet Access 81
14.3 Configuration Manager Program 81
15 Important Information 83
15.1 Product Care and Maintenance 83
15.2 Regulatory Information 83
15.2.1 EU Directives 83
15.2.2 Safety Approvals 87
15.2.3 EMC Approvals 87
15.2.4 Telecom Approval 90
15.2.5 Caution 90
15.2.6 Power Supply 91
15.2.7 Environmental Information 91
15.2.8 Intended Use 91
Glossary 92
Introduction
6 (98) EN/LZT 108 6492 R1
April 2003
1 Introduction
Congratulations on becoming the owner of an Ericsson ADSL Modem HM210dp/di.
Your LAN (Local Area Network) will now be able to access the Internet using your
high-speed ADSL connection. This User Guide describes how to install and set up
your HM210dp/di in a Windows environment, and how to customize its configuration
to get the most out of your new product.
1.1 Features
The ADSL Modem HM210 comes in two versions: HM210dp and HM210di. Both
products offer the same features, but they rely on different types of telephone line in
order to provide the ADSL service. HM210dp offers ADSL service over POTS (Plain
Old Telephone System) lines, while HM210di uses ISDN (Integrated Services Digital
Network) lines to provide the ADSL service.
The main features of the HM210dp/di are listed below:
•Internal ADSL modem for high-speed Internet access.
•10/100Base-T Ethernet router to provide Internet connectivity to all computers on
your LAN.
•Network address translation (NAT) and IP filtering functions to provide firewall
protection for your computers.
•Network configuration through DHCP.
•Configuration Manager program you access via a web browser.
1.2 Package Contents
Your package should contain all the components listed below. If any component is
missing or damaged, please contact the ADSL modem provider.
•ADSL Modem HM210dp/di
•A Power Supply Adapter with connecting cable
•Ethernet cable (straight-through)
•ADSL Line cable
•Quick Installation Guide.
Note:
Your package may also include other materials
provided by your ADSL operator.
1.3 System Requirements
In order to use your HM210dp/di, you must have the following:
•ADSL service up and running on your telephone line, with at least one public
Internet address for your LAN.
Introduction
EN/LZT 108 6492 R1 7 (98)
April 2003
•One or more computers each containing an Ethernet 10Base-T/100Base-T
network interface card (NIC).
•An Ethernet hub/switch, if you are connecting the device to more than one
computer.
•For system configuration using the built-in Configuration Manager program: a
web browser such as Internet Explorer v5.0 or later, or Netscape v5.0 or later.
Hardware Description and Connection
8 (98) EN/LZT 108 6492 R1
April 2003
2 Hardware Description and Connection
2.1 Front Panel and LED Indicators
The front panel of the HM210dp/di contains five control lamps (LEDs) that indicate
the status of the modem:
Figure 1: Front Panel of HM210dp/di
Label Color Function
PWR green ON: Unit is powered on.
OFF: Unit is powered off.
DIAG green Flashes ON/OFF at boot-up to indicate that the device software is
operational.
LAN green OFF: No Ethernet link detected.
ON: Ethernet link established and active.
ACT green Flashes when ADSL data activity occurs. May appear solid when data
traffic is heavy.
DSL green OFF: No ADSL link detected.
ON: ADSL link established and active.
Hardware Description and Connection
EN/LZT 108 6492 R1 9 (98)
April 2003
2.2 Back Panel and Connectors
The back panel of the HM210dp/di contains the connectors for the unit’s data and
power connections as described below:
Figure 2: Back Panel of HM210dp/di
Label Function
DSL Connects the HM210dp/di to an ADSL outlet (splitter/filter or phone outlet) using the
supplied ADSL Line cable.
LAN Connects the HM210dp/di to your PC's Ethernet port, or to the uplink port on your
LAN's hub, using the supplied Ethernet cable.
Reset button
(tiny hole)
Used to restore the HM210dp/di to its original factory default settings.
To reset the device to factory defaults, you don't need to power off the device. Just
push a paper clip into the hole and hold for 3 times before releasing. Then wait for the
device to finish boot-up.
Power
button Used to switch the HM210dp/di ON and OFF.
PWR Power socket for connecting the HM210dp/di to a power outlet by using the supplied
power adapter.
2.3 Placement
The HM210dp/di should be placed on a flat surface. Be sure to choose a location that
enables you to see the LEDs, is close to a power outlet, ADSL outlet, and the PC.
Note:
Proper ventilation is necessary to prevent the product
from over-heating. Do not block or cover the slots and
openings on the device, which are intended for
ventilation and proper operation.
Hardware Description and Connection
10 (98) EN/LZT 108 6492 R1
April 2003
2.4 Connecting the Hardware
Follow the procedures below to connect related devices. Before you begin, turn the
power off for all devices. These include your computer(s), your LAN hub/switch (if
applicable), and the HM210dp/di.
1Connect to the ADSL Line.
Connect one end of the provided ADSL Line cable to the port labeled DSL on
the back panel of the HM210dp/di. Connect the other end to your ADSL service
port (splitter/filter or phone outlet).
Note:
Depending on the service type offered by your ISP, an
additional splitter may be needed. If this is the case,
consult with your ISP for actual connection.
2Connect to a PC or hub/switch.
•To a single PC - Attach one end of the provided Ethernet cable
(straight-through) to the port labeled LAN on the HM210dp/di. Connect the
other end to your PC’sEthernet port.
•To a hub/switch - Attach one end of a “cross-over”Ethernet cable to a
hub/switch and the other end to the LAN port on the HM210dp/di.
•To a hub/switch’suplink port: - Use a “straight-through”cable to connect it
to the uplink port and the other end to the LAN port on the HM210dp/di.
3Attach the power connector.
Connect the provided Power cable to the PWR socket on the HM210dp/di. Plug
the power supply adapter into a power source (wall outlet or power strip).
4Turn on the HM210dp/di and power up your systems.
Press the Power button on the back panel of the HM210dp/di to turn on the
device.
Turn on and boot up your computer(s) and any LAN devices such as hubs or
switches.
This manual suits for next models
1
Table of contents
Other Ericsson Modem manuals
Ericsson
Ericsson 2400 User manual
Ericsson
Ericsson MINI-LINK PT 2010 ETSI Parts list manual
Ericsson
Ericsson HM210DP/DI User manual
Ericsson
Ericsson HM200c/HM201c User manual
Ericsson
Ericsson PipeRider HM200c User manual
Ericsson
Ericsson F3607gw User manual
Ericsson
Ericsson GC 75 User manual
Ericsson
Ericsson F5521gw User manual
Ericsson
Ericsson HM220d User manual
Ericsson
Ericsson C3607w User manual
