Epson 1520 - Stylus Color Inkjet Printer Specification sheet
Quick Setup
Unpack the Printer
Remove any packing material from the printer, as described on
the Notice Sheet in the box. Save all the packaging so you can
use it if you need to transport the printer later. You’ll find these
items inside:
4007158
Place the printer flat on a stable desk near a grounded outlet.
Leave plenty of room in back for the cables and for a stack of
continuous paper, if you use it. Leave enough room in front for
the paper support and output tray you’ll install in the next step.
Do NOT put the printer:
◗In an area with high temperature or humidity
◗In direct sunlight or dusty conditions
◗Near sources of heat or electromagnetic interference, such
as loudspeakers or cordless telephone base units
Also, be sure to follow the Safety Instructions in the Introduction
of your User’s Guide.
Here’s how to set up your new
EPSON Stylus®COLOR 1520 printer ...
○○○○○
black ink
cartridge
○○○○○
○○○○○○
color ink
cartridge
output tray
paper support
○○○○○○
cable cover
○○○○○○
1
Quick setupLoire2 5/22/97, 10:29 AM1
1. Place the hole in the right side of the paper support on
the printer’s right post. Then slightly lift the left side of the
paper support and push the notch down over the printer’s
left post.
Attach the Paper Support and OutputTray
○○○○○○○○
hole
○○○○○○○○○
notch
2. Press the two notches at the back of the output tray onto
the metal posts inside the printer.
Then flip down the legs on the underside of the output
tray so it sits up on the paper support.
○○○○○○○○○○
leg
○○○○○○○○○○○
post
○○○○○○○○○○
post
○○○○○○
leg
2
Quick setupLoire2 5/22/97, 10:29 AM2
Caution:
Do not plug the printer
into an outlet
controlled by a wall
switch or timer, or on
the same circuit as a
large appliance. This
may disrupt the power,
which can erase the
printer’s memory and
damage the power
supply.
1. First make sure the power is off. Check the Operate
button; it’s off when its surface is even with the button
guards on each side.
Plug In the Printer
○○○○○○○○○○○
Operate
2. Plug the power cord into a properly grounded outlet. To
protect the printer from power surges, you may want to
use a surge protector.
Install the Ink Cartridges
1. Press the Operate button to turn on the printer. The
Operate and Ink Out lights come on and the ink
cartridge holders move to the installation position. The
Pause light begins flashing.
2. Open the cover. The Cover Open light comes on.
3
Quick setupLoire2 5/22/97, 10:29 AM3
Warning:
If ink gets on your
hands, wash them
thoroughly with soap
and water. If ink gets in
your eyes, flush them
immediately with water.
3. Open the ink cartridge packages. Completely remove the
disposable yellow portion of the tape seal on top. Don’t
remove the white portion.
Caution:
You must completely
remove the yellow
portion of the tape seal
or you will permanently
damage the ink
cartridge. Don’t
remove the tape seal
from the bottom or ink
will leak.
5. Lower the ink cartridges into their holders with the labels
face up and the arrows pointing toward the back of the
printer.
4. Pull up the ink cartridge clamps.
4
Quick setupLoire2 5/22/97, 10:30 AM4
single sheet
icon
Load the Paper
6. Push down the clamps until they lock in place.
7. Press the Alt button to return the print heads to their home
position and charge the advanced ink delivery system.
Charging takes up to 7 minutes, with the Pause light
flashing until it’s finished; then the Pause light stays on.
Don’t turn off the printer or interrupt this important
process or you’ll use up more ink than necessary.
8. Close the printer cover. Then press the Pause button to turn
off the Pause light.
Caution:
Never turn off the printer
when the Pause light is
flashing. However, if the
Pause light is still flashing
after 10 minutes and the
printer is not moving or
making noise, you may
turn off the printer.
To test the printer operation, load about 10 sheets of letter-size
plain paper in the built-in sheet feeder as described here.
1. Make sure the paper release lever is set to the single sheet
position (the appears beneath the lever handle).
○○○○○○
5
Note:
For instructions on
loading other types of
paper or using the other
paper feeders, see your
User’s Guide
.
Quick setupLoire2 5/22/97, 10:30 AM5
2. Lock the output tray in an upright position on the two
upper posts.
3. Slide the right edge guide all the way left until it stops.
Then slide the left edge guide to match the approximate
width of your paper.
○○○○○○○○○○○
center this
midway
○○ ○○○○○
slide this to
paper’s width
○○○○○○
slide this left
4. Move the center support midway between the two edge
guides.
6
Quick setupLoire2 5/22/97, 10:30 AM6
5. Slide out the rear paper support guide until it stops.
6. Fan a stack of paper and then even the edges.
7. Load the stack with the printable surface face down and
slide it all the way into the feeder. Press the stack against
the right edge guide.
8. Slide the left edge guide against the left side of the paper.
Then slide the rear paper support guide against the end of
the paper.
9. Lower the output tray.
7
Quick setupLoire2 5/22/97, 10:30 AM7
Test the Printer
1. Turn off the printer and wait until the Operate light turns
off.
2. While holding down the Load/Eject button, turn on the
printer. Then release the Load/Eject button.
3. The first page prints on the first and last lines to measure
the page length. The next sheet prints a multicolor nozzle
check pattern and character samples at 360 dpi (dots per
inch).
Press the Pause button after the second page prints to
stop the test.
4. Press the Load/Eject button to eject any loaded pages.
Then turn off the printer.
If you have any problems with the test, see Chapter 7 in your
User’s Guide for more information.
Connecting to a PC
Connect the Printer toYour Computer
You can connect your EPSON Stylus COLOR 1520 printer to
either an IBM®compatible PC or an Apple®Macintosh.
®You’ll
need a shielded parallel cable to connect directly to a PC or an
Apple System Peripheral-8 serial cable to connect directly to a
Macintosh. (For a complete list of system requirements, see the
Introduction in your User’s Guide.)
To connect your printer to a network interface you must first
install an optional interface card. See Appendix A of your
User’s Guide for instructions.
1. Turn off the printer and your computer.
2. Connect the cable to the printer’s parallel interface; then
squeeze the wire clips together until they lock in place. (If
your cable has a ground wire, connect it now.)
8
Caution:
Never turn off the printer
while it’s printing test
pages. Always press the
Pause button and eject
any loaded paper first.
Quick setupLoire2 5/22/97, 10:30 AM8
Note:
The printer is assigned to
parallel port LPT1 when
you install the software; if
you want to use a different
port, see your Windows®
documentation for
instructions.
3. Connect the other end of the cable to your computer’s
parallel port and secure it as necessary. (See your
computer documentation for details.)
1. Turn off the printer and your Macintosh.
2. Connect one end of the cable to the serial connector on
the back of the printer.
Connecting to a Macintosh
3. Connect the other end of the cable to either the printer
port or the modem port on your Macintosh.
Note:
If you’re using a
PowerBook®with a
combination printer/modem
port, connect the printer to
that port. In the PowerBook
setup, set the port to
Normal. See your
PowerBook documentation
for more information.
If your Macintosh has a
built-in modem, use the
printer port.
if you have a ground
wire, connect it here
○○○○○○○○○
9
Quick setupLoire2 5/22/97, 10:30 AM9
Install the Printer Software
Now you need to install the printer software so you can
control printing from your computer.
You can install the printer software for Windows®95,
Windows 3.1, or Windows NT™3.51/4.0 from the EPSON
printer software CD-ROM. If you don’t have a CD-ROM drive,
you can create diskettes from the CD-ROM using another
computer.
The installation instructions are slightly different for each
Windows version. See the sections below for your operating
system.
Windows 95 Plug-and-Play
1. Turn on your printer, then turn on your computer.
2. At the New Hardware Found screen, make sure your
printer name is displayed and the Driver from disk
provided by hardware manufacturer button is selected.
Then click OK. (If you don’t see the New Hardware
Found screen, see “While Running Windows 95” below.)
3. Insert the EPSON printer software CD-ROM or diskette.
4. Type D:\or A:\(or the correct drive letter) and click OK.
5. At the next screen, keep or change the printer model
name. Then select Yes (No is the default) to use the
printer as the Windows default printer. Click Finish.
6. Follow the instructions on the screen. Your printer
software icons appear in an EPSON folder and a printer
icon appears in the Printers folder.
Installing on a PC
10
Note:
You’ll also find diskettes
for the EPSON Plot! utility
and AutoCAD®in your
printer box. (These utilities
are also on the CD-ROM.)
You don’t need to install
these utilities unless you
need to. See page 1 of
the Introduction to your
User’s Guide
for details.
Quick setupLoire2 5/22/97, 10:30 AM10
Other manuals for 1520 - Stylus Color Inkjet Printer
11
Table of contents
Other Epson Printer manuals
Epson
Epson Stylus Photo R265 Series Instruction Manual
Epson
Epson Stylus Photo 1270 User manual
Epson
Epson Aculaser 8500 User manual
Epson
Epson LX-80 User manual
Epson
Epson STYLUS PRO WT7900 User manual
Epson
Epson R340 - Stylus Photo Color Inkjet Printer Instruction Manual
Epson
Epson TX110 - Stylus Color Inkjet User manual
Epson
Epson TM-U330 Series User manual
Epson
Epson LQ-1070+ User manual
Epson
Epson DFX-9000 Instruction Manual
Epson
Epson STYLUS COLOR 777i User manual
Epson
Epson WF-100 User manual
Epson
Epson Stylus Office B1100 User guide
Epson
Epson ET-4550 Instruction Manual
Epson
Epson LX-1170 User manual
Epson
Epson WorkForce Pro WP-4500 Series User manual
Epson
Epson Expression Home XP-305 Assembly instructions
Epson
Epson Stylus COLOR 1160 Instruction Manual
Epson
Epson AcuLaser M1400 Series User manual
Epson
Epson WF-8090 User manual
