Epson MF1466-01 User manual
MF1466-01
CMOS 8-BIT SINGLE CHIP MICROCOMPUTER
(Adapter Board for S1C8F360/8F361)
S5U1C8F360Z1
Manual
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko
Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any
liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or
circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such
as medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there
is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright
infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic
products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from
the Ministry of International Trade and Industry or other approval from another government agency.
© SEIKO EPSON CORPORATION 2001 All rights reserved.
New configuration of product number
Starting April 1, 2001, the configuration of product number descriptions will be changed as listed
below. To order from April 1, 2001 please use these product numbers. For further information, please
contact Epson sales representative.
Devices
S1 C88104 F0A01
Packing specification
Package (D: die form; F: QFP)
Model number
Model name (C: microcomputer, digital products)
Product classification (S1: semiconductor)
Development tools
S5U1 C88348 D1 1
Packing specification
Version (1: Version 1)
Tool type (D1: Development Tool)
Corresponding model number (88348: for S1C88348)
Tool classification (C: microcomputer use)
Product classification
(S5U1: development tool for semiconductor products)
00
00
CONTENTS
S5U1C8F360Z1 MANUAL EPSON i
(ADAPTER BOARD FOR S1C8F360/8F361)
S5U1C8F360Z1 Manual (Adapter Board for S1C8F360/8F361)
This manual describes how to use the Adapter Board (S5U1C8F360Z1) that is a PROM writing and
evaluation tool for the 8-bit Single Chip Microcomputer S1C8F360/8F361.
Contents
CHAPTER 1INTRODUCTION ____________________________________________ 1
1.1 Outline of S1C8F360 Adapter Board (S5U1C8F360Z1) .............................1
1.2 Components of S1C8F360 Adapter Board (S5U1C8F360Z1) ..................... 1
CHAPTER 2PRECAUTIONS ____________________________________________ 2
2.1 Precautions for Operation ............................................................................ 2
2.2 Differences from the ICE88UR (S5U1C88000H5)
+ PRC88816 (S5U1C88816P) ..................................................................... 2
CHAPTER 3CONFIGURATION FOR THE S1C8F361 __________________________ 4
CHAPTER 4NAME AND FUNCTION OF EACH PART ___________________________ 5
CHAPTER 5SERIAL PROGRAMMING ______________________________________ 6
5.1 Setting the Jumpers ....................................................................................... 6
5.2 Connecting the Power Cable ........................................................................ 6
5.3 Pin Assignment of the CN4 Connector for Serial Programming .................6
CHAPTER 6CONNECTING WITH THE TARGET SYSTEM _________________________ 7
CHAPTER 7 S1C8F360 ADAPTER BOARD (S5U1C8F360Z1) SCHEMATIC DIAGRAM _9
CHAPTER 8PRODUCT SPECIFICATIONS ___________________________________ 10
CHAPTER 1: INTRODUCTION
S5U1C8F360Z1 MANUAL EPSON 1
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 1INTRODUCTION
1.1 Outline of S1C8F360 Adapter Board (S5U1C8F360Z1)
The S5U1C8F360Z1 board (hereafter Adapter Board) is a PROM writing tool for the 8-bit Single Chip
Microcomputers S1C8F360 and S1C8F361. The Adapter Board connected to the On Board Programming
Writer (S5U1C88000W3) allows writing user data to the Flash EEPROM built into the S1C8F360/8F361
(package model) placed on its IC socket using the On Board Programming Writer Control Software
(S5U1C8F360Y3).
The Adapter Board can also be used as a software evaluation board by mounting peripheral circuits on
the board.
S5U1C8F360Z1
1.2 Components of S1C8F360 Adapter Board (S5U1C8F360Z1)
After unpacking the S5U1C8F360Z1 package, check to see that all of the following components are
included.
(1) S5U1C8F360Z1 board................................................................ 1
(2) I/O cable (80-pin/40-pin ×2 flat type).................................. 2
(3) I/O cable (60-pin/30-pin ×2 flat type).................................. 1
(4) I/O connector for target system (40 pins)............................. 4
(5) I/O connector for target system (30 pins)............................. 2
(6) Power cable................................................................................. 1
(7) S5U1C8F360Z1 Manual (this manual) ................................... 1
(8) Warranty card............................................................................. 1
(9) User registration card ............................................................... 1
(10) Note for use ................................................................................ 1
CHAPTER 2: PRECAUTIONS
2EPSON S5U1C8F360Z1 MANUAL
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 2PRECAUTIONS
The connectors CN1, CN2 and CN3 have the same pin layout as the Peripheral Circuit Board for
S1C88816/8F360 (S5U1C88816P). This allows connection between the user target system for the
S5U1C88816P and the Adapter Board.
Take the following precautions when using the S1C8F360 Adapter Board (S5U1C8F360Z1):
2.1 Precautions for Operation
(1) Turn the power of all equipment off before connecting or disconnecting cables.
(2) Do not turn the power on while the input ports (K00–K03) are all set to low level. It may cause a
simultaneous key input reset.
2.2 Differences from the ICE88UR (S5U1C88000H5)
+ PRC88816 (S5U1C88816P)
The emulation system using the Adapter Board with an actual IC differs in terms of functionality and
characteristics from the S5U1C88816P emulation system, a fact which requires your attention. If these
differences are ignored, there is a possibility that your circuit will not operate properly on an actual IC
even though it might have performed well on the S5U1C88000H5 with the S5U1C88816P.
(1) Power supply differences
To operate the actual IC on the Adapter Board, an external power source voltage must be applied.
Refer to "Electrical Characteristics" chapter in the "S1C8F360 Technical Manual" for the supply
voltage.
(2) I/O differences
The output drive capability and pull up resistance are different.
The input setup time is different therefore, when a circuit requiring consideration of the input re-
sponse time, such as a key matrix, is used, the system and the software should be designed according
to the specifications for the actual IC.
(3) LCD differences
The output drive capability is different.
Since there will be differences with the actual IC even for the drive voltage, the system and the
software should be designed in order to adjust the characteristics.
(4) Analog comparator differences
The response time and characteristics of the analog comparator are different. Consequently, the
system and the software should be designed according to the specifications for the actual IC.
(5) Functional differences
<Oscillation circuit>
•The Adapter Board does not contain oscillator parts. Mount the parts according to the selected mask
option for the actual IC.
•The OSC3 oscillation stability time of the S5U1C88816P is shorter than that of the actual IC. There-
fore, the application program must take enough of interval (more than the oscillation stability time
in the actual IC) between starting the OSC3 oscillation and switching the system clock to OSC3.
•The logic level is different and it makes different oscillation timings such as the start and stop times.
•When switching the operating clock from OSC3 to OSC1, be sure to switch OSC3 oscillation off with
separate instructions. Using a single instruction to process simultaneously may cause a malfunction
of the CPU.
CHAPTER 2: PRECAUTIONS
S5U1C8F360Z1 MANUAL EPSON 3
(ADAPTER BOARD FOR S1C8F360/8F361)
•Do not turn the OSC3 oscillation circuit on in the low power mode.
Do not switch over the operating mode (normal mode ↔high speed mode) when the OSC3 oscilla-
tion circuit is on, as this will cause a malfunction.
<Internal power supply circuit>
The actual IC on the Adapter Board can change over the internal power voltage (set by VDC2, VDC1
and VDC0), but the S5U1C88816P cannot change the actual power voltage, because only the VDC2,
VDC1 and VDC0 values are changed.
For this reason, since the S5U1C88816P will operate, even if the stable time required for changeover is
not taken, be sure that the stable time is provided by the software.
Also, since the usable frequency of OSC1 and OSC3 depends on the internal power voltage, refer to
the technical manual for the S1C8F360 or S1C8F361 and take care so as not to operate it with an
inappropriate combination.
When turning the OSC3 oscillation circuit on after switching the operating voltage, the software must
take a voltage stabilization wait time of 5 msec.
<LCD drive power>
To drive an LCD using the Adapter Board, mount the parts required for VC1 to VC5 and CA to CE (CA
to CG in the S1C8F361) on the board or supply an external LCD power.
Note: The S1C8F360 Adapter Board supports the S1C8F361 as well.When using the board for the
S1C8F361, the AVDD and AVSS pins on the board must be changed to the CF and CG pins,
respectively, using the jumper and mount a capacitor to the holes indicated as C1.
<Reset circuit> ___________
Mount parts such as a switch and a capacitor at the RESET pin on the Adapter Board.
CHAPTER 3: CONFIGURATION FOR THE S1C8F361
4EPSON S5U1C8F360Z1 MANUAL
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 3CONFIGURATION FOR THE S1C8F361
The S1C8F360 Adapter Board (S5U1C8F360Z1) supports the S1C8F361 as well as the S1C8F360. In this
case, the pins listed in the table below change their functions.
Table 3.1 Pin function for S1C8F361
Print
AV
DD
AV
SS
S1C8F360
AV
DD
AV
SS
S1C8F361
CF
CG
When using the S1C8F361, open the AVDD and AVSS jumpers and mount the booster capacitor for the CF
and CG at C1.
CF
AVDD
AVSS
CG
C1
Fig. 3.1 CF and CG for the S1C8F361
This manual suits for next models
1
Table of contents
Other Epson Adapter manuals
Epson
Epson B32B867041 User manual
Epson
Epson OT-WL01 User manual
Epson
Epson 400 Series User manual
Epson
Epson Stylus Color 440 User manual
Epson
Epson BT-0260 User manual
Epson
Epson OT-WL01 User manual
Epson
Epson UB-P02II User manual
Epson
Epson WN7512BEP User manual
Epson
Epson OT-WL06 User manual
Epson
Epson OT-WL02 User manual
Epson
Epson PictureMate - Compact Photo Printer User manual
Epson
Epson ELPAP07 Instruction Manual
Epson
Epson EHDMC10 User manual
Epson
Epson ELPAP10 User manual
Epson
Epson EU-40 User manual
Epson
Epson SYS 1319-1005 User manual
Epson
Epson S5U13U00P00C100 User manual
Epson
Epson WN7512BEP User manual
Epson
Epson EX User manual
Epson
Epson WN6501CEP User manual
