Eneo MPD-64A0003P0A User manual
User Manual
EN
1/2.9” HD Dome, Fixed,
2560x1440, Day&Night, AF
Zoom, WDR, 3.2-9mm, Infrared,
Indoor
MPD-64A0003P0A
2
Table of content
Parts supplied ....................................................................................................... 5
Part names ............................................................................................................ 6
Operating instructions ........................................................................................ 10
Installation instructions ....................................................................................... 7
1. ZOOM / FOCUS ................................................................................................................................... 13
2. EXPOSURE .............................................................................................................................................. 16
3. SCENE ENHANCE ................................................................................................................................. 17
4. 3D-NR ..................................................................................................................................................... 19
5. DAY / NIGHT ........................................................................................................................................ 19
6. PICT. ADJUST ....................................................................................................................................... 21
7. SPECIAL ................................................................................................................................................. 22
8. SYSTEM ................................................................................................................................................. 24
9. EXIT ......................................................................................................................................................... 25
Open the dome cover ............................................................................................................................... 8
Detach the dome camera from the easy adaptor .......................................................................... 8
Power Supply connections ...................................................................................................................... 9
Pan & Tilt adjustment ............................................................................................................................... 9
Using OSD Control controller ............................................................................................................... 10
OSD menu table ......................................................................................................................................... 11
OSD Menu Setup .................................................................................................. 13
Further information ............................................................................................. 25
3
EN
Safety instructions
General safety instructions
•
• Keep the operating instructions in a safe place for later use.
• Installation, commissioning and maintenance of the system may only be carried out by authorised
individuals and in accordance with the installation instructions - ensuring that all applicable standards and
guidelines are followed.
• Protect the devices from water penetration and humidity, since these can cause lasting damage.
• Should moisture nevertheless enter the system, under no circumstance switch on the devices under these
conditions, instead send them for examination to an authorised specialist workshop.
•
• The device must be protected from excesses of heat, dust, humidity and vibration.
• When separating the system from the voltage supply, only ever use the plug to pull out the cable. Never
pull directly on the cable itself.
• Lay the connecting cables carefully and check that they are not mechanically stressed, kinked or damaged
and that no humidity can penetrate into them.
• In the event of a malfunction, please inform your supplier.
• Maintenance and repairs may only be carried out by authorised specialist personnel.
• The system must be isolated from the power supply before opening the housing.
•
• Connection cables should always be exchanged through Videor E. Hartig GmbH.
• Use only original spare parts and accessories from Videor E. Hartig GmbH.
• The housing should only be cleaned using a mild domestic cleaning agent. Never use solvents or petrol as
these can permanently damage the surface.
• During installation, it is essential to ensure that the seals provided are correctly installed and that they are
not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.
• The installer is responsible for the maintenance of the enclosure as per the technical data, e.g. by sealing
the cable outlets with silicone.
•
• The devices may only be operated in the temperature range indicated in the data sheet and within the
dened air humidity range.
• The camera may never be pointed directly at the Sun with the aperture open (this will destroy the sensor).
• It is unavoidable that during manufacture and to a certain extent during later use, humidity will be present
may condense inside the housing.
• To avoid this condensation inside the very tightly sealed housing, the manufacturer has inserted silica gel
sachets in the housing of the various camera types.
• It is however a physical given, that these silica gel bags will reach saturation after a certain amount of time.
They should therefore be replaced with new silica gel sachets.
• During installation, it is essential to ensure that the seals provided are correctly installed and that they are
not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.
• A multipolar, easily accessible isolation device should be installed in the proximity of the IR Spotlight, in
order to disconnect the device from the power supply for service work.
• The earth connection must be made according to the low impedance requirement of DIN VDE 0100.
• Subsequent painting of the equipment surface can impair the function.
• Any warranty claim is invalidated by subsequent painting.
• A safety margin of > 1m from the spotlight must be maintained when viewing directly into the IR Spotlight
in a darkened environment.
• Do not look directly at invisible LED radiation using optical instruments (e.g. a reading glass, magnifying
glass or microscope), since this can endanger the eyes, LED Class 1M.
• Operation of the IR spotlight with a defective cover or during repair is prohibited.
Before switching on and operating the system, rst read this safety advice and the operating instructions.
The system must never be used outside of the technical specications, since this can destroy it.
The device may only be opened by qualied service personnel. Unauthorised access invalidates any
warranty claim.
Wire end ferrules should be used when shortening the exible connection cables.
Product - Specic Safety Instructions
4
Class A device note
This is a Class A device. This device can cause malfunctions in the living area; in such an event, the operator may
need to take appropriate measures to compensate for these.
WEEE (Waste Electronical & Electronic Equipment)
Correct Disposal of This Product (Applicable in the European Union and other European countries with separate
collection systems).
This marking shown on the product or its literature, indicates that it should not be disposed with
other household wastes at the end of its working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable reuse of material resources. Household users
should contact either the retailer where they purchased this product, or their local government
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
Graphical symbols
Please pay attention to the safety instructions, and carefully read through this instruction guide before initial
operation.
Important points of warning are marked with a caution symbol.
iImportant points of advice are marked with a notice symbol.
5
EN
Parts supplied
• Indoor Dome camera
• Operating instruction
• Mounting Template
• Easy Adaptor (Flat type)
• Easy Adaptor (Tilted type)
• Plastic Anchor: 6 x 30mm (3x)
• Mounting Screw: 3.5 x 25mm (3x)
• Open Driver (1pc)
• Video Sub-out Cable (1pc)
6
Part names
Dome Cover
Lens
Bubble Shield
Bubble Dome
Dome Base
Easy Adaptor
(Flat type)
SMD LEDs
Light Sensor
Power Cable
3-Axis Gimbal
Tilted Easy Adaptor
OSD Menu Control board
7
EN
Installation instructions
CAUTION: The camera’s base should be attached to a structural
object, such as concrete, hard wood, wall stud or ceiling rafter
that supports the weight of the camera. If necessary use appro-
priate mounting material (e.g. anchors) instead of the material
enclosed with the camera.
1. Drill three holes for mounting on the ceiling or wall.
2. Place the Easy Adaptors at the pre-drilled installation position and x it by
using mounting screws.
3. Route the power/video cable to the connecting place.
4. Attach the dome base assembly to the Easy Adaptor.
5. Adjust the camera’s viewing angle (Pan, Tilt, Rotation)
6. Tighten the set screw to x a pan plate after the setting. Then remove the
caution sticker from the lens.
7. Assemble the dome cover to the dome base unit.
Mounting Screw (3.5x25mm)
Plastic Anchor (6x30mm)
OPEN
LOCK
8
CAUTION:
Tighten enough the dome cover xing screws so that there should
be NO gap between Lens hood and clear bubble to avoid the light
inow from IR LEDs.
Care should be taken the cable is NOT to be damaged, kinked or
exposed in the hazardous area.
Extreme care should be taken NOT to scratch the window in front
of lens.
Detach the dome camera from the easy adaptor
Push the hook on the dome base and swing the dome base to counter-clock
wise. Then detach the dome camera from the installed easy adaptor.
1
2
3
12
Open the dome cover
2. Hold the Dome housing with one hand and turn the open tool until Dome
Cover is suciently open.
1. Insert wide side of Open Tool into the lock of Dome Cover.
3. Once Dome Base and Dome Cover are detached, press the edge of Dome
Cover and pull it down with hands.
Extreme care should be taken NOT to apply force to IR LEDs.
9
EN
i
Pan & Tilt adjustments
Power supply connections
Please use the cable as provided with camera. If camera cable is cut and
re-wired, the transmission distance of video can be reduced.
Especially SDI cable should not be cut because it requires detailed wiring
job and aects the transmission distance.
1. Pan limit: Pan is limited to +/- 165°. Do NOT force to rotate the gimbal over the
limit to prevent from the internal damage.
2. Tilt limit: Tilt is limited to 25° min ~ 90° max. with reference to the ceiling when
the inclination of camera module is 0°, that is, the image is aligned horizontally.
3. Inclination limit (Horizontal image alignment): Inclination limited to +/-60° max.
25º
90º
10º
Tilted Easy Adaptor
Extended Viewing angle
15º
※SDI OUTPUT
(Yellow)
ANALOG OUTPUT
(Black)
POWER ( )
Camera can be operated with the regulated or unregulated DC12V but
the regulated power supply of DC12V is recommended.
Camera is protected from the damage by the reverse connection of polarity.
Operating Instruction
10
Using OSD controller
Setup menu can be accessed and controlled by OSD control joystick on the rear
of the camera unit. Five commands are available with the joystick.
OSD Control
Joy Stick
Video Format
DIP Switch
EX-SDI↔HD-SDI
i
i
HD-SDI or EX-SDI is selectable by Video format switch only.
TVI mode or AHD mode is selectable in the menu only.
(SYSTEM> ANALOG MODE)
1. SET (●) : Access to the menu or enter the setting. To enter the main menu,
press the Set Key down.
2. UP/DOWN (▲/▼) : Choose the desired sub-menu and to move the cursor up
or down.
3. LEFT/RIGHT (◄/►) : Set up the value of the selected menu. Used to adjust the
desired menu selection and to move the cursor left or right.
Description of the OSD control operation
4. ‘ ’ denotes the long press down straightly for about 2 seconds
Description of the Motorized ZOOM&FOCUS adjustment
1. ▲: Zoom In
2. ▼: Zoom Out
3. ◄: Focus Near
4. ►: Focus Far
Works only when OSD Menu is inactive.
Video Sub-out Connector
Table of contents
Other Eneo Security Camera manuals
Eneo
Eneo IPD-68M3611P5A User manual
Eneo
Eneo MEP-62M2812M0A User manual
Eneo
Eneo VKCD-1333SM/49 User manual
Eneo
Eneo IPC-53M2812M0A User manual
Eneo
Eneo HDC-2080Z03 User manual
Eneo
Eneo INP-7 Series User manual
Eneo
Eneo GLC-1601 User manual
Eneo
Eneo IN Series User manual
Eneo
Eneo IPP-83A0036MIA User manual
Eneo
Eneo IPD-42F0028PAA User manual
Eneo
Eneo PXD-2080MIR C User manual
Eneo
Eneo VKC-1360 User manual
Eneo
Eneo INP-54M2812M0A User manual
Eneo
Eneo MPP-62A0020M0A User manual
Eneo
Eneo VKC-1324A/W3 User manual
Eneo
Eneo VKC-1425 User manual
Eneo
Eneo NXD-1602M User manual
Eneo
Eneo MSM-42F0037MPA User manual
Eneo
Eneo 219546 User manual
Eneo
Eneo NXP-880F Series User manual
