Emulex LP982 Installation and operating manual
LP982 Installation and Reference Manual
Table of Contents
Installation
Compatibility
Prerequisites
Install HBA
Attach Media
Apply Power
View LEDs
Reference
Specifications
FCC and Regulatory Notices
Declaration of
Conformity
Laser Safety
Emulex Drivers, Software and Manuals
1
Chapter 1 − Installation
Table of Contents
Compatibility
Prerequisites
Install HBA
Attach Media
Apply Power
View LEDs
Emulex Drivers, Software and Manuals
2
Installation
Caution Emulex LightPulse ® Host Bus Adapters (HBAs) contain
electronic components that can be damaged by static
electricity through an electrostatic discharge (ESD) event.
To prevent ESD damage, maintain constant contact with
any grounded metal surface. A grounding wrist strap is
useful for this purpose. Handle the card carefully at all
times and preferably by the edges. Avoid touching
electronic components and keep the card in the original
packaging until you are ready for installation.
Compatibility
Software
Environments Windows Server 2003, Windows 2000, Windows NT,
Linux, NetWare
Hardware
Environments PCI hardware platforms: x86
Prerequisites
Host computer must provide 3.3 VDC bus power
One open 32−bit or 64−bit (64−bit recommended) PCI or PCI−X bus
slot with 3.3 VDC +/− 5%
•
•
PCI bus clock rate of 33 MHz or 66 MHz• PCI−X bus clock rate of 66 MHz, 100 MHz, or 133 MHz• Media and connectors•
Emulex Drivers, Software and Manuals
3
Install the Host Bus Adapter Board
Record IEEE and serial numbers.
Each host bus adapter is shipped with a unique 64-bit identifier
called the IEEE address. The Fibre Channel industry uses a World
Wide Name (WWN) derived from the IEEE address, and this number
is needed for Fibre Channel connectivity. The serial number is used
when communicating with Emulex. Both numbers are clearly marked
on the board. We recommend that you record these numbers before
installation.
1.
Turn off and unplug the computer.2. Remove the computer case.3. Remove the blank panel from an empty 32− or 64−bit PCI or PCI−X
bus slot. Compare the removed panel to the bracket on the host bus
adapter. Follow steps 5−8 to change the bracket if they are different
sizes.
4.
Note The host bus adapter comes with a standard PCI
bracket installed. The low−profile mounting bracket
is shorter than the standard bracket; approximately
3.11 in. (7.9cm) compared to 4.75 in. (12.06 cm)
long.
Remove the mounting bracket screws from the top of the host bus
adapter.
5.
Remove the bracket and store it for future use.6. Align the new mounting bracket tabs with the holes in the HBA.7.
Note Be careful not to push the bracket past
the transceiver housing's grounding tabs.
Replace the screws that attach the HBA to the bracket.8. Insert the host bus adapter into the empty 32− or 64−bit PCI or PCI−X
bus slot. Press firmly until it is seated.
9.
Emulex Drivers, Software and Manuals
4
Secure the host bus adapter's mounting bracket to the case with the
panel screw or clip.
10.
Replace the computer case and tighten case screws.11.
The host bus adapter is now installed in the PC and is ready for media
attachment.
Emulex Drivers, Software and Manuals
5
Attach Media
Note The host adapter will not allow normal
data transmission on an optical link unless
it is connected to another similar or
compatible laser product (that is,
multimode to multimode.)
Use multimode fiber optic cable used by short−wave lasers and that adheres to
the following specifications:
Fiber Optic Cable Maximum Length Minimum
Length Connector
62.5/125 µm
(multimode) 300 meters at 1.0625
Gb/s
150 meters at 2.125
Gb/s
2 meters LC
50/125 µm
(multimode) 500 meters at 1.0625
Gb/s
300 meters at 2.125
Gb/s
2 meters LC
Connect the fiber optic cable to the LC connector on the host adapter
board as shown.
Connect the other end of the cable to peripheral device or loopback.2.
1.
After the media is connected to the host adapter, you are ready to apply power
to the computer.
Emulex Drivers, Software and Manuals
6
Apply Power
Verify that the host bus adapter is securely installed in the computer.1. Verify that the correct media is attached.2. Plug in and turn on the computer.3. Observe LEDs for Power On Self Test (POST) results.4.
View LEDs
Green and yellow display lights (LEDs) can be seen through openings in the
host bus adapter's mounting bracket. Green indicates power and yellow
signifies port activity.
POST conditions and results are summarized in this table.
Green
LED Yellow
LED State
OFF OFF Wake−up failure (dead board)
OFF ON POST failure (dead board)
OFF Slow blink (1 Hz) Wake−up failure (dead board)
OFF Fast blink (4 Hz) Failure in POST (dead board)
OFF Flashing (irregular) POST processing in progress
ON OFF Failure while functioning
ON ON Failure while functioning
ON Slow blink (1 Hz) Normal − 1 Gb link rate
ON Fast blink (4 Hz) Normal − 2 Gb link rate
Blink (1 Hz) OFF Normal − link down or not yet started
Emulex Drivers, Software and Manuals
7
Chapter 2 − Reference
Table of Contents
Specifications
FCC and Regulatory Notices
Declaration of Conformity
Laser Safety
Emulex Drivers, Software and Manuals
8
Reference
Specifications
Parameter Range
Media
Interface The Pegasus ASIC interfaces to the physical media through
an FC−0 Media Interface (FC−PI compliant transceiver),
and then connects through an optical fiber LC connector.
Physical
Dimensions The PCI adapter accommodates two form factors:
The short PCI form factor, 6.875 inches by 4.2
inches, with a full−height bracket
•
The low−profile MD2 form factor, 6.600 inches by
2.536 inches, with a low−profile bracket.
•
Power
Requirements + 3.3 VDC, + or – 5 % , 2.3A typical (3.3A maximum)
Airflow 100 lf/min (minimum)
Temperature 32° to 113° F (0° to 45° C), Operating
−40° to 158° F (−40° to 70° C), Storage
Humidity 5% to 95% non−condensing
Agency
Approvals for
LP982
Class 1 Laser Product per DHHS 21CFR (J) & EN60825
UL recognized to UL1950
CUR recognized to CSA22.2, No.950
Baurt−certified by TUV to EN60950
FCC Rules, Part 15, Class A
Industry Canada, ICES−003, Class A
EMC Directive 89/336/EEC (CE Mark)
EN55022, Class A
EN55024
Australian EMC Framework (C−Tick Mark)
AS/NZS 3548: Class A
Japan VCCI, Class A
Emulex Drivers, Software and Manuals
9
FCC and Regulatory Notices
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A` LASER DE CLASSE 1
Model LP9802−F2/LP982−F2
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense. Shielded cables
must be used between this equipment and attached peripheral devices. The
reader is cautioned that changes or modifications made to the equipment not
expressly approved by Emulex could void the user's authority to operate this
equipment. The above statement applies to products marketed in the USA
This class A digital apparatus meets all requirements of the Industry Canada
(IC) Interference − Causing Equipment Standard (ICES−003).
Cet appareil numerique de la Classe A respecte toutes les exigences du
reglement sur le materiel brouilleur du Canada.
This statement applies to products marketed in Canada.
Responsible Party: Paul Folino, President & CEO, Emulex Corporation, 3535
Harbor Blvd., Costa Mesa, CA 92626, USA, (714) 662−5600
VCCI Notices and Translations (Japan Only)
NoteVCCI regulations provide that changes or modifications not
expressly approved by Emulex Corporation could void your
authority to operate this equipment.
Emulex Drivers, Software and Manuals
10
Table of contents
Other Emulex Adapter manuals
Emulex
Emulex LP1005DC-CM2 User manual
Emulex
Emulex LP10000ExDC Installation and operating manual
Emulex
Emulex LP9802DC Installation and operating manual
Emulex
Emulex LP10000 User manual
Emulex
Emulex LP10000DC Installation and operating manual
Emulex
Emulex LP952L Installation and operating manual
Emulex
Emulex LP1050Ex Installation and operating manual
Emulex
Emulex NC551i User manual
Emulex
Emulex LPe1150 HBA User manual
Emulex
Emulex LP10000 Use and care manual
Emulex
Emulex LPe11004 HBA Assembly instructions
Emulex
Emulex LP1050 Installation and operating manual
Emulex
Emulex LP10000 Installation and operating manual
Emulex
Emulex LPE11000 HBA User manual
Emulex
Emulex OneConnect OCe14000-Series User manual
Emulex
Emulex AW520A User manual
Emulex
Emulex LP1050DC Installation and operating manual
Emulex
Emulex LPe11002 HBA User manual
Emulex
Emulex LP21000 User manual
Emulex
Emulex LP9402DC Installation and operating manual
