Eltron LP2022 User manual
User’s Manual No. 980008-001
Rev. B
©1995 Eltron International Inc.
LP/LP+ Series
User’s Manual
Models:
LP2022, LP2042
LP2122, LP2142
FOREWORD
This manual provides installation and operation information for LP & LP+ Series printers
manufactured by Eltron International Incorporated, Simi Valley, California. The contents
includes installation & operation instructions.
TECHNICAL SUPPORT
If for any reason you require product technical support, please contact the Distributor where
you first purchased your equipment. If they cannot help you or at their direction, Eltron
Technical Support can be reached at:
Eltron International Incorporated Eltron International, Europe
41 Moreland Road Unit 2, Rose Kiln Lane
Simi Valley, CA. 93065 Reading, Berkshire, RG2 OHP England
(800) 344-4003 +44 (0) 1734 752 024
FAX (805) 579-1808 FAX: +44 (0) 1734 752 005
e-mail: eltro[email protected]
BBS: (805) 579-3445
Return Materials Authorization
Before returning any equipment to Eltron for in warranty or out of warranty repair, contact
Repair Administration for a Return Materials Authorization (RMA) number. Repack the
equipment in the original packing material and mark the RMA number clearly on the outside.
Ship the equipment, freight prepaid, to the address listed below.
Eltron Repair Adminstration
41 Moreland Road
Simi Valley, CA 93065-1692
(805) 579-1800
FAX (805) 579-1808
COPYRIGHT NOTICE
This document contains information proprietary to Eltron International Incorporated. This
document and the information contained within is copyright by Eltron International Incorpo-
rated and may not be duplicated in full or in part by any person without prior written approval
of Eltron. While every effort has been made to keep the information contained within current
and accurate as of the date of publication, no guarantee is given or implied that the document
is error-free or that it is accurate with regard to any specification. Eltron reserves the right to
make changes, for the purpose of product improvement, at any time.
TRADEMARKS
LP Series and LP+Series are service marks and Eltron is a trademark of Eltron International
Incorporated. Windows & MS-DOS are registered trademarks of Microsoft Corp. All other
marks are trademarks or registered trademarks of their respective holders.
980008-002 Rev. B
iii
WARRANTY INFORMATION
We Need To Hear From You!
To establish your warranty period and provide access to Technical Support,
Send Us Your Product Registration Card Today!
Eltron warrants the mechanism, control electronics and power supply, under normal use and
service, to be free from defects in material and workmanship for a period of twelve months
from the date of purchase by the end user. Eltron warrants the printhead, under normal use
and service, to be free from defects in material and workmanship for a period of 90 days from
the date of purchase by the end user. Proof of purchase or product registration is required.
If proof of purchase or product registration cannotbe established, shipment date to the original
buyer (dealer or distributor) will be be used to establish warranty period.
Failure to exercise caution to protect the equipment from electrostatic discharge damage,
adverse temperature and humidity conditions or physical abuse may void the warranty. Eltron
will, at it’s option, repair or replace the equipment or any parts which are determined to be
defective within this warranty period and which are returned to Eltron F.O.B. factory of origin.
The warranty set forth above is exclusive and no other warranty, whether written or oral, is
expressed or implied. Eltron specifically disclaims the implied warranties of merchantability
and fitness for a particular purpose.
FCC Notice:
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference in which case
the user will be required to correct the interference at his own expense.
CSA Notice:
This equipment does not exceed Class A limits per radio noise emissions for digital apparatus set out in the Radio Interference
Regulation of the Canadian Department of Communications. Operation in a residential area may cause unacceptable
interference to radio and TV reception requiring the owner or operator to take whatever steps are necessary to correct the
interference.
Cet equipment ne depasse pas les limites de Classe A d’emission de bruits radioelectriques pour les appareils numerriques
tells que perscrites par le Reglement sur le brouillage redioelectrique etabli par le ministere des Communications du Canada.
L’exploitation faite en milieu residentiel peut entrainer le brouillage des receptions radio et tele, ce qui obligerait le proprietaire
ou l’operateur a pendre les dispositions necessaires pour en eliminer les causes.
CE Notice
This equipment has been tested and found to comply with the European Council Directives only when used with a double
shielded parallel interface cable such as Eltron part number 300058-006. Use of a lower grade interface cable may result in
RF emissions that cause unacceptable interference toradio and TV reception requiring the owner or operator to take whatever
steps are necessary to correct the interference.
iv
980008-002 Rev. B
Table Of Contents
Getting Started
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . 2
Parts Check List . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operation
Controls & Indicators . . . . . . . . . . . . . . . . . . . . . . 9
Loading Labels or Tags . . . . . . . . . . . . . . . . . . . . . 12
Threading The Label Dispenser . . . . . . . . . . . . . . . . . 17
AutoSense Gap Sensor Adjustment . . . . . . . . . . . . . . . 19
Cleaning The Print Head . . . . . . . . . . . . . . . . . . . . 20
Replacing the Printer Memory Backup Battery (LP+ Only) . . . 21
Appendix A - Troubleshooting . . . . . . . . . . . . . . . . 25
Appendix B - Supplies and Accessories . . . . . . . . . . . 37
Appendix C - Windows Printer Driver . . . . . . . . . . . . 39
980008-002 Rev. B
v
vi
980008-002 Rev. B
1
Getting Started
This section provides information on the instal-
lation of the printer and software.
Introduction
The LP Series and LP+ Series printers are low
cost direct thermal printers specifically de-
signed for printing labels, tags or continuous
receipts (with or without bar codes) from any
DOS™or Windows™ or ASCII based compat-
ible computer.
Features
•Direct thermal printing for reliability.
•Supports over 13 types of bar code sym-
bologies.
•High resolution print head for sharpgraphics
and text.
•Download forms, fonts and graphics perma-
nently to removable memory cartridges
(LP+ Series).
980008-001 Rev. B
1
Unpacking the
Printer
The printer is shipped in a carton and protec-
tive bag. Keep all packing material in case you
need to move or re-ship the printer. Avoid
touching the electrical connectors to prevent
Electro-Static Discharge damage while setting
up the printer.
The discharge of electrostatic energy that accu-
mulates on the surface of the human body or
other surfaces can damage or destroy the print
head or electronic components used in this
device.
Getting Started
2
980008-001 Rev. B
Parts Check List
Your printer kit should contain the items listed
below.
•The LP or LP+printer.
•The printer Power Supply.
•Create-A-Label Tools software disk & man-
ual (LP+ only).
•Printer User’s Guide (this manual).
•1 roll of Sample Labels and Spool.
•1 printer Cleaning Card.
If any items are missing, contact your dealer for
replacement parts.
Getting Started
980008-001 Rev. B
3
Installation
The following sections will step you through the
installation of the printer and Create-A-Label
Tools software.
Step ➊
Attach Power
Supply
Place the printer in a suitable location that
allows easy access to printed labels. The printer
should never be operated while resting on it’s
side or upside down. Place the power supply
in a suitable location, preferably on the floor
near an electrical outlet. Check that the printer
power switch is in the OFF (0) position. Attach
the printer power cable to the jack at the rear
of the printer, near the power switch. Check the
label on the power supply for input voltage
requirements. Attach the power supply line
cord to an electrical outlet of the proper volt-
age.
The printer and power supply should never be
operated in a location where either one can get
wet. Personal injury could result.
Getting Started
4
980008-001 Rev. B
This manual suits for next models
3
Table of contents
Other Eltron Printer manuals
Eltron
Eltron P2242 Series User manual
Eltron
Eltron LP2642 User manual
Eltron
Eltron TLP2046 User manual
Eltron
Eltron LP2642 User manual
Eltron
Eltron TLP2046 User manual
Eltron
Eltron Eclipse LP2344 User manual
Eltron
Eltron PRIVILEGE P500 User manual
Eltron
Eltron Strata Series User manual
Eltron
Eltron P210 Guide User manual
