Elsner WS1000 Color Owner's manual

Conversion WS1000 without Touch WS1000

Color

Assembly

information

WS1000 Color

Please also observe the assembly instructions and the WS1000 Color manual!

Information on assembly Page 1 of 2 Status: 06/05/2015

Preparing the WS1000 Color

To remove the WS1000 Color front-

plate, open the screws under

the flap.

Slide the upper part of the WS1000 Color housing (frame with

display) slightly upwards and lift it off.

Beware: The display is connected to the circuit board in the

concealed box by a flat cable. Loosen the plug in order to be

able to remove the upper part.

The covering flap is only loosely mounted, take care not to lose

it.

The lower part of the housing, including the wall mounting

plate, is fixed to the concealed box by 3 screws: Loosen the

screws and remove the lower part.

Connection

Remove the circuit board from the WS1000 Color. Place it in the

concealed box of the old WS1000.

Since the mounting plugs for the old concealed box do

not align

with the mounting holes in the new circuit board, this must be

screwed directly to the rear wall.

Beware: The circuit boardmust never be exposed to dust

or humidity!

5) Connect the drives etc. In doing so keep the individual connecting wires as short as possible in

order to avoid unnecessary reserve loops. Contact between motor cables on the processor circuit

board can cause the display to malfunction.

Conversion WS1000 without Touch WS1000

Color

Assembly

information

WS1000 Color

Please also observe the assembly instructions and the WS1000 Color manual!

Information on assembly Page 2 of 2 Status: 06/05/2015

Assembling the new controller with adapter plate

Connect the adapter plate earth with the WS1000 Color circuit

board. The protective conductor can be connected to the PE

terminal for the mains connection or to a vacant drive group of

the WS1000. Alternatively, a protective conductor terminal on

the building can be used for earthing.

Pull the display cable through the recess in the adapter plate

and screw the plate on to the old controller's concealed box.

Use the screws from the old WS1000.

Also pull the display cable through the recess in the WS100

Color wall mounting plate and screw the lower part onto the

adapter plate (3 M4 countersunk Allen screws are provided with

the adapter plate).

Connect the display and screw on the upper part of the WS1000 Color housing (frame and display).

Other manuals for WS1000 Color

Table of contents

Other Elsner Controllers manuals

Elsner

Elsner KNX eTR 208 Light/Sunblind Guide

Elsner

Elsner KNX Touch One Style Guide

Elsner

Elsner Solexa II Parts list manual

Elsner

Elsner KNX eTR Sunblind Series Guide

Elsner

Elsner WS1000 Color User instructions

Elsner

Elsner 71200 User manual

Elsner

Elsner KNX S4-B10 230 V Guide

Elsner

Elsner Cala KNX M-T CH Series Guide

Elsner

Elsner KNX eTR Sunblind User manual

Elsner

Elsner KNX S1E-UP 230V Guide

Elsner

Elsner KNX S1R-UP Guide

Elsner

Elsner Cala KNX T 201 Sunblind Guide

Elsner

Elsner Solexa 230V Guide

Elsner

Elsner Cala KNX M-T Series Guide

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual