Elba EH-E9122ST(BK) User manual
1
For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully
before operating your set.
Retain it for future reference.
Record model number and serial
number of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
DESIGNER HOOD
MODEL: EH-E9122ST(BK)
2
Please read this instruction carefully. It is advisable to keep this instruction
manual in a safe place for future reference.
SAFETY PRECAUTIONS
1. Keep electrical appliances out of reach from children. Do not let them to
operate the appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the product,
cord or plug into water or any other liquid.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities unless they have been
given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
5. If the power cord or plug is damaged, it must be replaced by the service
centre or a qualified service technician to avoid hazard.
6. Before installation, check if the mains supply voltage is matched with the
voltage stated on the rating plate of the hood.
7. There must be adequate air ventilation of the room when the cooker hood
is used with the cooking appliances with burning gas or other fuels.
8. Ensure that the installation of exhaust complies with the standard of local
building, gas and electrical authorities.
9. Do not ignite flames in the pans.
10.There is a risk of fire if cleaning is not carried out in accordance with this
instruction.
3
ASSEMBLY INSTRUCTIONS
Please check the following before installation:
Installation of hood must be carried out by an authorized or qualified technician.
Remove all packaging materials from the cooker hood. Check and make sure
that the cooker hood is not damaged.
Please ensure the power supply has switched OFF when installing the hood.
For optimum air extraction, avoid having too many windows surrounding the
cooker hood which will cause air convection.
The optimum height for the installation is between 350 to 450mm which
measure from the bottom of the hood to the top of the hob.
Make sure the hood is in level after installation to avoid oil spill over from the oil
cup collectors.
Before installing, determine the height between the bottom of the cooker hood to
the top of the hob. Mark on the wall to suit the bracket locations.
Drill 4 holes with diameter of Ø8mm and 60mm deep. Insert the screw anchors
into the holes. Fix the mounting bracket and tighten the screws.
Remove the horizontal oil cup. Hang the hood on the mounting bracket and
make sure the hood is in level.
Fix the exhaust ducting on the hood. Install the oil cups on the cooker hood.
Install the telescopic exhaust cover to the height required.
Before connecting to the mains supply, ensure that the mains voltage
corresponds to the voltage on the rating plate inside the cooker hood.
4
PRODUCT DESCRIPTIONS
1 Switch/Delay Function –To switch the cooker hood to standby mode and turn
off the cooker hood. Press this button during operation to schedule three
minute delay timer to turn off the cooker hood.
2 Low Fan Speed –Press this button to operate low fan speed.
3 High Fan Speed –Press this button to operate high fan speed.
4 Turbo Fan Speed –Press this button to operate turbo fan speed for one
minute (after one minute will revert to high fan speed).
5 Lamp Illumination –To switch on/off the LED lamp.
OPERATING INSTRUCTIONS
1 Press the button and press the button to operate the cooker hood in
low speed. Press the button to operate the cooker hood in high speed.
Press the button to operate the cooker hood in turbo speed. This
function will revert to high speed after one minute.
2 When the motor is running, press button to schedule the cooker hood to
turn off after three minutes. Press button again when the cooker hood in
delay off mode to turn off the cooker hood immediately.
3 Press the button to turn on the LED lamp. Press again to turn off. (This
function does not relate to the cooker hood motor).
5
CLEANING AND MAINTENANCE
The hood must always be disconnected from the electricity supply before
carrying out the maintenance.
Clean the hood with damp cloth, hot water and mild detergent. Do not use
chemical, steel, wooden or abrasive cleaners to clean the hood.
Remove the oil cups in horizontal direction, wash in hot soapy water, dry and fit
back into the hood. Do not use the hood without the oil cup installed.
Avoid spilling water into motor and electronic component.
CLEANING THE INNER PART
Disconnect the power supply and then pull the glass panel from the bottom with
both hands from the left and right. Remove the glass panel from the locking nut
and push the panel upward with both hands to take down the panel slowly.
Loose the screws on the air inlet ring and then take out the filter.
6
Turn the locknut in clockwise direction to take out the impeller.
REPLACING THE LIGHT BULB
Disconnect the power supply, push the panel upward
with both hand to take down the panel slowly
Slightly insert the screwdriver in the edge of the lamp
and pry downward to take out the LED lamp (2W).
Disconnect the connecting cable of LED lamp (2W) and
replace a new LED lamp unit (2W). Connect the power
supply to ensure LED lamp (2W) is function.
※The LED lamp bulb is shall not be greater than 2W.
TROUBLESHOOTING
Malfunctions
Possible Root Cause
Checking
Weak Suction
The distance is too far between
the hood and stove
Lower down the Hood installation
height but within the safety guideline
Strong convection due to too
much ventilation
Shut off some of the windows or
doors
Hood and light not
function
The power supply not connected
Check the plug is well connected and
power is switched on
Power cord is damaged
Contact technicians for repair
Motor function but light
not works
Light bulb is damaged
Replace a new light bulb ( 2W)
Light works but motor
not function
The bearing may be damaged
Contact technicians to repair
The internal wires or motor
capacitor may be burnout
Vibration on the hood
The screw is loosen
Tighten the screws
The hood is noisy
Exhaust pipe surface is distorted
Contact technicians to reinstall the
exhaust pipe
7
MAIN SPECIFICATION
Rated Voltage : 220-240V/50Hz
LED Light : 2W x 2
Suction Power : 1,400m³/hr
Motor Power : 250W
Product Dimension : 898 mm (W) x 996-1343mm (H) x 428mm (D)
PRODUCT SIZE
NOTICE
This product must not be disposed together with domestic waste. It has to be disposed at an
authorized place for recycling of electrical and electronic appliances. By collecting and recycling
waste, you help to save natural resources and make sure the product is disposed in an
environmental friendly and healthy way.
8
Table of contents
Other Elba Ventilation Hood manuals
Elba
Elba HS60CSEX3 Mounting instructions
Elba
Elba EH-H9329TFT(BK) User manual
Elba
Elba Covo 668 User manual
Elba
Elba PLANET Series User manual
Elba
Elba CASA 679 User manual
Elba
Elba EH-M9138ST User manual
Elba
Elba EH-G9325ST User manual
Elba
Elba Aria EH-A9023ST(SS) User manual
Elba
Elba MARS-V2-90 IS-X User manual
Elba
Elba COVO 669/90GP User manual
Elba
Elba 2937/90MC User manual
Elba
Elba EH-E9121ST(BK) User manual
Elba
Elba 506A Series User manual
Elba
Elba ARIA EH-A9024ST User manual
Elba
Elba EH-N9128ST User manual
Elba
Elba ELIO 9365 User manual
Elba
Elba EH-J9031ST(SS) User manual
Elba
Elba STELLA 90-IS BGX User manual
Elba
Elba CCH5191SS User manual
Elba
Elba RH-601 X User manual
