Ei Electronics Ei127 User manual

Pattress Models Ei127 & Ei127R

For use only with Ei140, 141, 144, 145, 146, 161, 161R,

164, 164R, 166, 166R Easi-Fit Smoke/Heat Alarms

The Smoke/Heat Alarm is mounted on the Ei127 & Ei127R.

The Ei127 pattress facilitates installation of bulky wiring and con-

duits.

The Ei127R has an additional socket for connecting to the R

spade terminal on the Ei161R, Ei164R or Ei166R. This can be

used for remote test & hush or manual call points.

WARNING: This pattress must only be used with one of the

above smoke alarms as per these instructions - otherwise the unit

will not comply with the mandatory safety regulations.

Installation

WARNING: First disconnect the mains from the circuit to be used.

1. Choose a mounting position following the siting instructions in

the Smoke/Heat Alarm leaflet. Where the incoming wiring is on

the surface of the ceiling, the appropriately sized ducting/conduit

must be chosen to mate with the unit. Use a sharp knife to

remove material from the selected knockout, making sure that

there is no gap when mated with ducting / conduit. There are four

knockouts – three on the sidewall and one on the rear.

2. Screw the pattress to the ceiling after first removing the

required knockout and bringing the house wires through it (see

figure 1). Use the longer screws and plasterboard anchors from

the Smoke Alarm pack for this task. If the central knockout is

SURFACE

CONDUIT

CABLE

ENTRY

Ei161R/164R/166R

REMOTE CONTROL ONLY

CONNECT TO SMOKE / HEAT ALARM

MOUNTING PLATE TERMINALS

EARTH - (IF PRESENT)

N - NEUTRAL

IC - INTERCONNECT

L - LIVE

REAR

KNOCKOUT

FOR MOUNTING PLATE

Figure 1

being used, seal around the wires (and the openings at the rear

of the pattress) with silicone or similar to prevent air draughts

affecting the smoke entering the alarm.

3. Connect the house wires (L - Live, N - Neutral and IC -

Interconnect, if it is being used) to the terminal block on the pat-

tress. If an Ei161R, Ei164R or Ei166R (with remote TEST/HUSH)

is being installed, attach the “R” wire from the Ei152 (see the

Ei152 instructions) to the terminal marked “R” in the pattress (see

figure 1). If the Ei161R, Ei164R or Ei166R is being used with a

manual call point then connect the R terminal to the call point (see

figures 1& 2). Otherwise do not connect anything to the ”R” termi-

nal.

4. Connect the three wires (L, N and IC) from the pattress con-

nector block to the connectors on the Smoke/Heat Alarms mount-

ing plate. Connect the earth wire (if present) from the house wir-

ing directly to the terminal on the mounting plate. Replace the

cover over the terminal wires.

Note: that the house wiring can be connected directly to the

mounting plate if the pattress terminals are not being used for

looping.

5. Screw the mounting plate to the pattress pillars using the two

screws supplied with this kit.

6. Slide the alarm on to the mounting plate.

7. Connect the mains power – the green LED light on the alarm

should be on. When the test button is pressed the horn should

sound.

If an Ei128R or Ei128RBU pattress with relay is being used,

replace the Ei127R with the Ei128R or Ei128RBU and follow the

instructions supplied with it.

Aico Ltd

Mile End Business Park,

Maesbury Road, Oswestry, Shropshire SY10 8NN, U.K.

Telephone: 0870 7584000 www.aico.co.uk

Ei Electronics

Shannon Industrial Estate,

Shannon, Co. Clare, Ireland

www.eielectronics.com

Figure 2

This manual suits for next models

Table of contents

Other Ei Electronics Smoke Alarm manuals

Ei Electronics

Ei Electronics B16009-R0-160RC Series User manual

Ei Electronics

Ei Electronics Ei 105B User manual

Ei Electronics

Ei Electronics MCP401RC User manual

Ei Electronics

Ei Electronics Ei650 Series User manual

Ei Electronics

Ei Electronics Ei2110 User manual

Ei Electronics

Ei Electronics Ei 3105TY User manual

Ei Electronics

Ei Electronics Heat Alarm Ei 164R Heat User manual

Ei Electronics

Ei Electronics Ei 181 Ionisation User manual

Ei Electronics

Ei Electronics EiA600 Series User manual

Ei Electronics

Ei Electronics Ei160 Manual

Ei Electronics

Ei Electronics Heat Alarm Ei 103R User manual

Ei Electronics

Ei Electronics Ei 3105TYCH Optical User manual

Ei Electronics

Ei Electronics Ei 169 Manual

Ei Electronics

Ei Electronics Easichange Series User manual

Ei Electronics

Ei Electronics Ei166R User manual

Ei Electronics

Ei Electronics Ei2110e Series User manual

Ei Electronics

Ei Electronics Ei141EK User manual

Ei Electronics

Ei Electronics Ei 156TLR Optical User manual

Ei Electronics

Ei Electronics BROOKS EIB160e Series User manual

Ei Electronics

Ei Electronics Ei 105R Optical User manual

Ei Electronics

Ei Electronics Ei3100RF? Ei3500RF Manual

Ei Electronics

Ei Electronics Ei603 Series User manual

Ei Electronics

Ei Electronics Ei140e Series User manual

Ei Electronics

Ei Electronics Ei154TL User manual

Popular Smoke Alarm manuals by other brands

x-sense

x-sense SD19-W user manual

BRK electronic

BRK electronic First Alert P1010 quick start guide

FireAngel

FireAngel Thermoptek ST-622 user manual

teko

teko Astra-42A user guide

Safetec

Safetec SDS-2/6 Additional Fault Finding Instructions

Siemens

Siemens PE-11C installation instructions

System Sensor

System Sensor DH500ACDC Installation and maintenance instructions

Resolution Products

Resolution Products RE612 CryptiX quick start guide

First Alert

First Alert PC900V user manual

Eminent

Eminent EM6590 E-Domotica user manual

Carrier

Carrier Kidde Quell Q301 user manual

VESDA

VESDA VLF-500 Product guide

ELRO

ELRO FS8110 instruction manual

Heiman

Heiman SMOKI NS-626PHS user manual

Regin

Regin SDD-S65 instruction manual

Family Gard

Family Gard FG225 user manual

Greystone

Greystone DSD120 Installation and maintenance instructions

Aparton

Aparton ASD-10 Instructions for use