Edimax EN-9130TX User manual

Fast Ethernet Adapter

10/100Mbps PCI

Fast Ethernet Adapter

EN-9130

User’s Manual

Fast Ethernet Adapter

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply

with the limits of a Class B computing devices,

pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications.

If you suspect this product is causing interference, turn

your computer on and off while your radio or TV is

showing interference. If the interference disappears

then when you turn the computer off and reappears then

you turn the computer on, something in the computer is

causing interference.

You can try to correct the interference by one or more

of the following measures :

1. Reorient/Relocate the receiving antenna.

2. Increase the separation between the equipment and

receiver.

3. Connect the equipment into an outlet on a circuit

difference from that to which the receiver is

connected.

4. Ensure that all expansion slots (on the back or side

of the computer) are covered. Also ensure that all

metal retaining brackets are tightly attached to the

computer.

1Introduction

Thanks you for purchasing our 10/100Mbps Fast

Ethernet Adapter. This guide is to provide the

installation and usage of this adapter for network

installers and users. The 10/100 network adapter

complies to PCI 2.1 and PCI 2.2 specification and

supports half/full duplex feature which can double

network speed.

This adapter supports both 10Mbps and 100Mbps

network speed, 100BaseTX operates on two pairs of

category 5 UTP cable and 10BaseT operates on

Category 3,4,5 UTP cable.

With the Auto-Negotiation technology, network speed

is auto detected. When you connect the adapter to

10BaseT hub via UTP cable, the network speed

becomes 10Mbps. Similarly, if you connect the adapter

to 100BaseTX hub, the network speed is 100Mbps. If

the hub is a switching hub which supports full duplex

function, then the speed will be doubled to

20Mbps/200Mbps.

Real hassle free installation is achieved by conforming

to PCI bus. Just plug in the card and all setup is done

automatically. No more software to run !

Furthermore, this adapter support the Wake On LAN

(WOL) feature allows users to configure network

adapters that are capable of “listening to” network

packets even when the computer is turned off.

This adapter supplies many drivers including ODI

driver for NetWare 3.x/4.x/5.x, NDIS driver for

MicrosoftLANManager,Windows95/98/NT/2000/Me/

XP, Linux, and a Packet Driver for TCP/IP software.

Whatever your requirements are ease of installation,

superior performance or responsive support backed up

by unlimited technical support, this adapter is the

superior choice.

2Features & Specifications

(1) Features & Benefits

Supports 32-bit PCI Bus Master for high performance

and low processor utilization.

Complies to PCI 2.1 and PCI 2.2 specification

Complies with the IEEE 802.3 CSMA/CD,

100BaseTX and 10BaseT standard.

Full duplex design to double the performance to

20Mbps/200Mbps.

One UTP connector for 100Mbps or 10Mbps network

speed.

Support Auto-negotiation function.

Built-in FIFO buffers to eliminate external memory.

Auto-setups IRQ and I/O address.

Supports early interrupt on transmit to increase

performance.

Supports ODI driver for NetWare 3.x/4.x/5.x; NDIS

driverforLANManager,Windows95/98/NT/2000/Me/XP,

Linux, and Packet Driver for TCP/IP software.

Provides diagnostic software and one LEDs to

indicate LNK/ACT

selection.

Supports smart remote Boot ROM

(2) Technical Specification

Topology : Star

Connector : RJ-45

Standard : IEEE 802.3 10BaseT

IEEE 802.3u 100BaseTX

Transmission Rate :10Mbps or 20Mbps

100Mbpsor 200Mbps

Hardware Required : IBM compatible PC with

available PCI slot

( PCI 2.1 or PCI 2.2 )

IRQ Line : Assigned by system

I/O Address : Assigned by system

Drivers : ODI driver for NetWare 3/4/5

NDIS driver for LAN Manager,

Windows 95/98/NT/2000/Me/XP

Linux,Packet Driver for TCP/IP

software.

Temperature : 00Cto 550C (Operating)

Humidity : 10%to 90% (Non-condensing)

Certification : FCC Class B, CE Mark

Microsoft Certified

Power consumption : 1.8W (Max.)

3Installation

(1) Hardware Installation

To insert the network adapter into your PC, follow the

steps bellow :

1. Turn off the computer and remove its cover.

2. Insert the adapter into a PCI slot.

3. Secure this adapter to the rear of the computer

chassis and put back the computer cover.

4. Connect the adapter to the network using twisted-

pair cable.

(2) Hardware Requirement for Wake On LAN

If your motherboard support the PCI 2.1 only, then

the motherboard must provide a 3-pin WOL

connector.

(Some computers may require you to change a setting

in your computer’s BIOS or setup program to enable

the WOL feature.)

If the motherboard support PCI 2.2, we don’t need

the 3-pin WOL connector. ( the function will be

provided from the PCI bus directly )

ATX 2.01 power supply.

Note : Install only one active WOL adapter per

computer. You can install additional,

non-WOL adapters.

(3) Hardware Installation for Wake On LAN

If your motherboard support the PCI 2.2 standard, no

other procedure is needed. But, you still can follow the

steps (for PCI 2.1) below on the PCI 2.2 motherboard,

and all the function include the WOL will work

normally.

If the motherboard support PCI 2.1 only, please follow

the next procedure,

1. Unpack the 3-pin auxiliary power cable.

2. Insert the 3-pin auxiliary power cable into the

connector on the adapter.

3. Attach the 3-pin auxiliary power cable to the

connector on the PC motherboard.

(4) Driver Installation

Use the drivers supplied by the diskette included in this

product. For detail description, please refer to

readme.doc or readme.exe in the diskette provides by

this product.

4Trouble-shooting

If you experience any problems with the adapter, first

make sure the appropriate driver is loaded, the proper

cable is connected to the adapter port and the hub

complies with the adapter specification, such as

10Mbps 10BaseT or 100Mbps 100BaseTX, then check

the LED.

The adapter provides one LEDs to indicate network

status.

Lnk/Act

A green LED indicates if the NIC has been LINK ok or

not. When the light is OFF, it indicates that the UTP

port has not been connected or LINK not ok. When the

light is ON, it indicates that the UTP port LINK ok.

When the light is BLINKING, it indicates that there is

traffic flow on the network which the adapter is

connected to.

( Wake On LAN )

The PC can not boot up after installing the

adapter.

1. Remove the 3-pin cable from the PC connector.

2. Boot up the PC, run setup program to configure the

adapter as “Active Low”(Default setting is “Active

High”)

3. Turn off the PC and reconnect the 3-pin cable to the

PC.

4. Boot up the PC again.

The PC does not boot up when a Magic

Packet or Wake Up Frame is sent.

1. Check the specification of this PC meets the

hardware requirement in chapter 2.

2. Verify the BIOS setting of Wake On LAN is

configured properly. (Please check your computer

owner’s manual or contact your dealer for more

information.)

3. Remove the PC cover and check the 3-pin cable

connection.

4. Run configure program to check the setting of this

adapter.

5. If the adapter still does not wake up, install a known

good working Wake On LAN adapter and 3-pin

auxiliary power cable in the PC and recheck the PC.

[!] Contact your dealer if problem persist.

TRADEMARKS

part of this manual may be reproduced, transcribed,

stored in a retrieval system, translated into any

language or computer language without the prior

written consent of Edimax.

All brand and product names are trademarks and/or

registered trademarks of their respective companies.

Other manuals for EN-9130TX

This manual suits for next models

Table of contents

Other Edimax Adapter manuals

Edimax

Edimax EW-7318USg User manual

Edimax

Edimax EW-7722UTn V2 Instruction manual

Edimax

Edimax HP-5101 User manual

Edimax

Edimax EW-7106PC User manual

Edimax

Edimax EU-4208 User manual

Edimax

Edimax HP-5102ACK User manual

Edimax

Edimax BT-8500 User manual

Edimax

Edimax EU-4306 User manual

Edimax

Edimax EW-7711UAn User manual

Edimax

Edimax HP-5102K User manual

Edimax

Edimax EW-7618Ug User manual

Edimax

Edimax EP-4203DL User manual

Edimax

Edimax EW-7317UG User manual

Edimax

Edimax Wireless USB Adapter 11g & 11n User manual

Edimax

Edimax EW-7608Pg User manual

Edimax

Edimax EW-7317UHg User manual

Edimax

Edimax EW-7811UTC User manual

Edimax

Edimax EU-4206 User manual

Edimax

Edimax EW-7822UAC Instruction manual

Edimax

Edimax HP-5202Wn User manual

Edimax

Edimax EW-7822PIC User manual

Edimax

Edimax HP-5001 User manual

Edimax

Edimax EP-4103DL User manual

Edimax

Edimax EW-7618Ug User manual

Popular Adapter manuals by other brands

PCB Piezotronics

PCB Piezotronics 090B274 Installation and operating manual

Auvidea

Auvidea J20 Technical reference manual

Gossen MetraWatt

Gossen MetraWatt AT3-III E operating instructions

Akribis

Akribis ITF-21-BISS-MIT user manual

Tenda

Tenda W54U user guide

ROHO

ROHO AGILITY Operation manual

PROLiNK

PROLiNK WN2001 Quick installation guide

Hawking

Hawking HUF2 Specifications

Airlink101

Airlink101 AWLC4030 user manual

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter user manual

Philips

Philips SWA4554S/10 user manual

JVC

JVC TS-C9D2B Assembly and installation instructions

NETGEAR

NETGEAR A6100 quick start

D-Link

D-Link DWA-121 Quick install guide

Philips

Philips SWA2037 Specifications

Basalte

Basalte 0610-20 installation manual

Yealink

Yealink EHS40 user guide

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A installation guide