ECRM KnockOut 4550 Manual
IMAGESETTERS THAT MAKE REAL SENSE
554 Clark Rd.
Tewksbury, MA 01876
Phone (508) 851-0207 Fax - (508) 851-7016
AG11693 - Rev. 8
Document No.
Consisting of:
AG11693 Rev 8 Cover Sheets
AG11718 Rev 6 Operator Guide Text
AO11693 Rev 6
KnockOut 4550®
Operator Guide
KnockOut 4550®
Operator Guide
This guide reflects the KnockOut 4550 as of August, 1997.
© copyright ECRM Incorporated, 1997
Information on ordering additional copies of this manual may be obtained by writing or
calling:
ECRM
Order Processing
554 Clark Road
Tewksbury, MA 01876
Phone No. (
US
) - (508) 851-0207 — Fax (
US
) - (508)-851-7016
Phone No. (
UK
) - (44) 1923-218255 — Fax (
UK
) (44) 1923-218256
Phone No. (
Hong Kong
) - 852-2-564-8989 — Fax (
Hong Kong
) 852-2-564-8821
AppleLink
ECRM.SUPPORT (
US
)
ECRM.UK (
UK
)
FEP.ECRM (
Hong Kong
)
Proprietary Notice
The information contained within this guide is the property of ECRM Incorporated. No transmis-
sion, reproduction, transcription, storage in a retrieval system, translation into any language, or
other use is permitted in whole or in part in any form without first obtaining written permission of
ECRM Incorporated.
List of Trademarks or Registrations, ECRM
®
is a registered trademark of ECRM Incorporated, PelBox
®
is a registered trademark of
ECRM Incorporated, KnockOut 4550
is a registered trademark of ECRM Incorporated.
AG11693 Rev. 8
Table of Contents
AG11718 Rev 6 i
INTRODUCTION 1-1
PRODUCT COMPLIANCE 2-1
PRODUCT COMPLIANCE DEFINITIONS 2-1
CSA - Canadian Standards Association 2-1
DOC - Department of Communications 2-1
IEC - International Electrotechnical Commission 2-1
FCC - Federal Communications Commission 2-1
LASER 2-1
LASER Product 2-1
LASER Radiation (Light) 2-2
LASER System 2-2
Operation and Maintenance 2-2
Service 2-2
TÜV 2-2
VDE 2-2
LASER SAFETY 2-3
LASER Product Classification 2-3
DESCRIPTION OF LABELS 2-5
Identification and Certification Label (Ratings Plate) 2-5
LASER Warning Labels (Non-interlocked covers) 2-6
LASER Warning Labels (Interlocked Covers). 2-7
PRODUCT SAFETY 2-9
CSA 2-9
TÜV 2-9
ELECTROMAGNETIC EMISSIONS 2-10
FCC - USA 2-10
DOC - CANADA 2-11
EMC Directive - EUROPE 2-11
CONTROL PANEL 3-1
INTRODUCTION 3-1
MENU KEYS 3-2
USING SYSTEM MENUS 3-3
OPERATION AND MAINTENANCE 4-1
INTRODUCTION 4-1
ii AG11718 Rev 6
Table of Contents
Table of Contents
SETTING UP THE SYSTEM 4-2
System Setup 4-2
User Setup 4-9
4-10
LOADING MEDIA INTO A 400 FOOT INPUT CASSETTE 4-14
LOADING MEDIA INTO A 200 FOOT INPUT CASSETTE 4-18
ADJUSTING THE INPUT CASSETTE SHELF 4-22
INSTALLING MEDIA INTO THE SYSTEM 4-23
TRANSPORT MODE 4-27
CLEARING MEDIA JAMS 4-29
Buffer Media Jams 4-29
Output Slot Media Jam 4-30
STATUS MESSAGES 4-31
TRANSPORT STATUS DISPLAY 4-36
ERROR MESSAGES 4-40
ROLLER CLEANING PROCEDURE 4-41
AIR FILTER CLEANING PROCEDURE 4-44
EMPTYING THE PUNCH TRAY 4-45
CLEANING THE SYSTEM 4-45
APPENDIX A A-1
DIAGNOSTIC MENU A-1
Introduction
AG11718 Rev 6 1-1
1
Introduction
This book provides the information you will need to operate
your imagesetter. Some of the topics covered are: Laser Regu-
lations, The Control Panel, Operating Menus, Loading Film
Into the Cassette, Loading the Cassette into the System, and
Status and Error Messages.
Section 2 contains important safety information about the laser
and the covers and interlocks that the system contains to pre-
vent accidental exposure to the laser beam. Please read this
information carefully.
ATTENTION!
This symbol is used throughout the Operator Guide
to alert you to cautions, warnings and other
important notes.
WARNING
LIVE CIRCUITS BEFORE MAINS SWITCH!
AC power is connected to theVoltage Selector
Switch, Line Filter, AC Fan Fuse, AC Fan, and Mains
Switch.This circuit does NOT shut off when the
mains switch is turned off.To remove power from this
circuit, unplug the AC Line Cord from the rear of the
system.
1-2 AG11718 Rev 6
Introduction
1
.
IMPORTANT!
System fan is ALWAYS ON!
Prior to connecting the imagesetter to the AC mains sup-
ply voltage, ensure the AC Fan Line Voltage Selector
Switch (located on the bottom of the rear panel) is set for
proper mains supply voltage.
WARNING!
If the AC Fan LineVoltage Selector Switch is set incorrectly
when the imagesetter is plugged in, damage may occur to
the imagesetter.
AC Fan LineVoltage
Selector Switch
SCSI Interface
Connector PelBox Interface
Connector
On Line Processor
Connector
Introduction
AG11718 Rev 6 1-3
IMPORTANT NOTE!
If mains supply voltage is removed from the imagesetter
(turning off the fan) while the imagesetter is connected to
online film processor, remove the cover on the film pro-
cessor.This will prevent the film processor fumes from
getting into the imagesetter.
1-4 AG11718 Rev 6
Introduction
1
Table of contents
